2014 NISSAN TEANA headrest

SE-70
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seat cushion trim, firmly push down while slid- ing your hand along the seams as shown ( ) to ensure the hook
fasteners below the seat cushion trim are fastened properly.
REAR SEATBACK ASSEMBLY (RH) - WITH REMOVABLE HEADREST
Disassembly
1. Remove the rear seatback assembly (RH). Refer to SE-36, "Removal and Installation - Seat Assembly".
2. Remove the armrest assembly. Refer to SE-38, "Removal and Installation - Armrest Assembly"
.
3. Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper
4. Remove the seatback trim and s eatback pad (2) from the seat-
back frame (1).
a. Release the J-clip retainers (A) from the seatback frame (1).
b. Remove two hog rings that retain seatback pad in place. : Hog ring
PIIB3356J
ALJIA0656ZZ
ALJIA0941ZZ
ALJIA0942ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-71
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
c. Release the headrest holder locks as shown and remove the headrest holders (1) from the seatback frame (2).
CAUTION:
Before removing headrest holder, check its orientation
(front/rear and right/left).
d. Remove the seatback trim and seatback pad from the seatback frame.
5. Separate the seatback trim from the seatback pad.
a. Pull seatback trim (1) upward to release hook fasteners (A).
b. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened ar ound both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seatback trim, firmly push down while sliding your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
ALJIA0943ZZ
ALJIA0944ZZ
PIIB3356J
ALJIA0656ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SE-72
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
REAR SEATBACK ASSEMBLY (RH) - WITHOUT REMOVABLE HEADREST
Disassembly
1. Remove the rear seatback assembly (RH). Refer to SE-36, "Removal and Installation - Seat Assembly".
2. Remove the armrest assembly. Refer to SE-38, "Removal and Installation - Armrest Assembly"
.
3. Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper
4. Remove the seatback trim and s eatback pad (2) from the seat-
back frame (1).
a. Release the J-clip retainers (A).
b. Remove two hog rings that retain seatback pad in place. : Hog ring
c. Remove the seatback trim and seatback pad from the seatback frame.
5. Separate the seatback trim from the seatback pad.
a. Pull seatback trim (1) upward to release hook fasteners (A).
b. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened ar ound both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
ALJIA0941ZZ
ALJIA0942ZZ
ALJIA0950ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-73
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seatback trim, firmly push down while sliding
your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
REAR SEATBACK ASSEMBLY (LH) - WITH REMOVABLE HEADREST
Disassembly
1. Remove the rear seatback assembly (LH). Refer to SE-36, "Removal and Installation - Seat Assembly".
2. Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper
3. Remove the seatback trim and seatback pad (2) from the seat- back frame (1).
a. Release the J-clip retainer (A).
PIIB3356J
ALJIA0656ZZ
ALJIA0945ZZ
ALJIA0946ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SE-74
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
b. Release the headrest holder locks as shown and remove theheadrest holders (1) from the seatback frame (2).
CAUTION:
Before removing headrest holder, check its orientation
(front/rear and right/left).
c. Remove the seatback trim and seatback pad from the seatback frame.
4. Separate the seatback trim (1) from the seatback pad.
a. Pull seatback trim upward to release hook fasteners (A).
b. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened ar ound both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seatback trim, firmly push down while sliding
your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
REAR SEATBACK ASSEMBLY (LH) - WITHOUT REMOVABLE HEADREST
ALJIA0943ZZ
ALJIA0947ZZ
PIIB3356J
ALJIA0656ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM