2014 NISSAN JUKE ignition

5To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
FIRST DRIVE FEATURES
NISSAN INTELLIGENT KEY® SYSTEM (if so equipped)
The NISSAN Intelligent Key® System allows you to lock or
unlock the vehicle, open your liftgate and start the engine.
It is important to make sure the Intelligent Key is with you
(that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch

01, push the liftgate request switch 02
or press the
button
03 on the key fob.

To unlock the vehicle, perform one of the
following procedures:
• Push any door handle request switch
once;
the corresponding door will unlock. Push
the request switch again within 1 minute;
all other doors will unlock, or
• Press the

button
04 on the key fob to
unlock the driver’s side door. Press the

button 04 again; all other doors will unlock.

The Intelligent Key can also be used to activate the panic
alarm by pressing and holding the
button
05 for more
than 1 second. Once activated, the panic alarm and
headlights will stay on for a period of time.
INTELLIGENT KEY BATTERY DISCHARGE

If the battery of the Intelligent Key is discharged, or
environmental conditions interfere with the Intelligent
Key operation, start the engine according to the
following procedure:
1. Move the shift lever to the P (PARK) position
(Continuously Variable Transmission) or to the
N (NEUTRAL) position (manual transmission).
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key
and a chime will sound.
4. Within 10 seconds after the chime sounds, push
the ignition switch while depressing the brake pedal
and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
01
03
04
05
02

7To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
STARTING/STOPPING THE EN GINE (NISSAN Intelligent Key®
models only - if so equipped)
CONTINUOUSLY VARIABLE TRANSMISSION
(if so equipped)

It is important to make sure the NISSAN Intelligent
Key® is with you (that is, in your pocket or purse).

Depress the brake pedal.

Move the shift lever to the P (PARK) position.

Push the ignition switch to start the engine.
H EATE D S EATS (if so equipped)
The seats are warmed by built-in heaters. The
switches
01, located on the center console, can
be operated independently of each other.

Push the HI (high) side of the switch for high heat.
Push the LO (low) side of the switch for low heat.

The indicator light on the switch will illuminate when
the heater is on. The indicator light will remain on as
long as the switch is on.

To turn off the heater, return the switch to the level position. Be certain the
indicator light turns off.

The heater is controlled by a thermostat, automatically turning the heating
element on and off.

When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn
the switch off.
For more information, refer to the “Instruments and Controls (section 2)” of your Owner’s Manual.
02
01
OUTSIDE MIRROR CONTROL SWITCH
The outside mirror control switch is located on the
left side of the instrument panel.

To select the left or right mirror, move the switch 01.

Adjust each mirror to the desired position, using the
control switch

02.

To prevent accidentally moving the mirror, move
switch

01 to the center (neutral) position.For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
01

8To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
FIRST DRIVE FEATURES
HEADLIGHT CONTROL SWITCH
HEADLIGHT CONTROL

Turn the headlight control switch to the
position
01 to turn on the front parking, side marker, tail, license
plate and instrument panel lights. Turn the switch to the
position
02 to turn on the headlights.
AUTOLIGHT SYSTEM (if so equipped)

The autolight system will automatically turn the headlights on when it is\
dark and off when it is
light. The system will keep the headlights on for a period of time after you tur\
n the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
position
01, or
position
02.
HIGH BEAM SELECT

Push the headlight control switch forward
04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull the
headlight switch back to the original position to
select the low beam. The blue indicator light goes off.

Pull and release the headlight control switch
05 to
fl ash the headlight high beams on and off.
FOG LIGHT SWITCH (if so equipped)

The headlights must be on and the low beams

position 02 selected for the fog lights to operate.

Turn the switch (inside collar) to the position
06
to turn the fog lights on.

Turn the switch (inside collar)
to the OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
01
02
04
05
MANUAL TRANSMISSION (if so equipped)

Depress the brake pedal.

Move the shift lever to the N (NEUTRAL) position.

Depress the clutch pedal to the fl oor while pushing the ignition switch to start the engine.
TURNING THE ENGINE OFF

For a Continuously Variable Transmission, move the shift lever to the P (PARK) position, apply
the parking brake and push the ignition switch.

For a manual transmission, apply the foot brake and place the vehicle in \
1st gear, then apply the
parking brake and push the ignition switch.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
06

9To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
WINDSHIELD WIPER AND WASHER SWITCH
Move the lever to the following positions to operate
the windshield wipers:
01 Mist (MIST) - One sweep operation of the
front wipers.
02 Intermittent (INT) - Wipers operate intermittently.
The intermittent speed can be adjusted by
rotating the control ring
03 to increase or
decrease wiper speed.

04 Low (LO) - Front wipers operate at a continuous
low speed.

05 High (HI) - Front wipers operate at a continuous
high speed.

06 Pull the lever toward you to activate the
front washer. The front wipers will operate
several times.
REAR WINDSHIELD WIPER AND WASHER

07 Intermittent (INT) - Rear wiper operates
intermittently.

08 Low (ON) - Rear wiper operates at a continuous
low speed.

09 Push the lever forward to activate the rear washer.
The rear wiper will operate several times.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order to replace\
the wiper blades.
To move the wiper blades to the service position, follow this procedure:

Turn the ignition switch to the OFF position.

When the ignition switch is in the ON position or within 60 seconds of placing the ignition
switch to the OFF position, push the windshield wiper and washer lever up to the MIST
position
01 two times in less than 0.5 seconds. The windshield wipers will move to the
service position automatically, and the wiper blades can now be replaced.
To move the wiper blades back to the original position:

Pull the windshield wiper and washer lever up for more than 1 second or \
push the lever
down to operate at any wiper speed.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
02
04
05
MIST
OFF
INT
LO
HI
06
09
03
INT
ON07
08

14To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
TRIP COMPUTER
With the ignition switch in the ON position, trip computer

01 modes can be selected by pressing the trip computer
mode switch 02 on the instrument panel. The following
modes can be selected in the display:

Trip A – measures the distance of one specifi c trip.

Trip B – measures the distance of a second specifi c trip.

Current Fuel Consumption – displays the current fuel consumption.

Distance to Empty (dte) – displays the estimated distance to empty (dte) the vehicle can
be driven before refueling.

Average Fuel Consumption – displays the average fuel consumption since\
the last reset.

Elapsed Time – displays the time since the last reset.

Torque Vectoring AWD (AWD model) – displays the current amount of torque distributed
to each wheel.
Push the reset switch
02 for approximately 1 second to reset the currently displayed trip
odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
BLUETOOTH® HANDS-FREE PHONE SYSTEM
A cellular telephone should not be used while driving
so full attention may be given to vehicle operation.*
SYSTEM OPERATING TIPS
Press the button to interrupt the voice prompts
at any time and speak a command after the tone.

The “Help” command can be used to hear a list of
available commands at any time.

Reduce background noise as much as possible
by closing windows and pointing HVAC vents away
from the ceiling.

Speak in a clear and natural voice without pausing
between words.

When speaking Phonebook names, please be aware
some phones require the last name to be spoken
before the fi rst name. For example, “Michael Smith”
may be spoken as “Smith Michael”.

To cancel a voice recognition session simply wait 5 seconds, say “Cancel” or “Quit”, or
press and hold the
button for 5 seconds.

To increase or decrease the volume of the voice prompts, push the volume \
control switches
+ or - on the steering wheel or turn the control dial on the audio syste\
m while the audio system
is responding.
02
01
SYSTEM GUIDE