2014 MITSUBISHI OUTLANDER SPORT heater

Horn switch6-54 Instruments and controls
6
E00508000640
Press the steering wheel on or around the“ ”mark.
zSince the demister requires a significantamount of power, stop the demister as soonas the window is demi
sted. Using it for a
long time may reduce the auxiliary batteryvoltage, making it impossible to start thePlug-in Hybrid EV System.zOn vehicles equipped with heated mirrors,when the rear window demister switch ispressed, the outside rear-view mirrors aredefogged or defrosted. Refer to “Heated mir-ror” on page 7-9.zOn vehicles equipped with the wiper deicer,when the rear window demister switch ispushed, the window glass becomes warmand the wipers become operable. Refer to“Wiper deicer switch” on page 6-53.NOTE
zIt is possible to cha
nge the setting to make
the rear window demister operate automati-cally when ambient
temperature becomes
low while the ready indicator lamp is illumi-nated, even if you do not push the rear win-dow demister switch.It operates automatica
lly only once after put-
ting the operation mode in ON.If you choose this setting, the heated mirrors(if so equipped) and
wiper deicer (if so
equipped) will also operate automatically atthe same time.For further informati
on, we recommend you
to consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.zThe demister switch is
not to melt snow but
to clear mist. Remove snow before use of thedemister switch.zWhen cleaning the inside of the rear window,use a soft cloth and
wipe lightly along the
heater wires, being careful not to damage thewires.zDo not allow objects to
touch the inside of
the rear window glass,
damaged or broken
wires may result.NOTE
Horn switch
BK0203201EN.book 54 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Outside rear-view mirrors
Starting and driving 7-9
7
The mirrors automatically retract or extendwhen the doors are locked or unlocked usingthe remote control switches or the keylessoperation function of the keyless operationsystem.Refer to “Keyless operation system: To oper-ate using the key-less operation function,Keyless entry system” on pages 4-9.
E00601201582
To d e m i s t o r d e f r o s t t h e o u t s i d e r e a r - v i e wmirrors, press the rear window demisterswitch.The indicator lamp (A) will illuminate whilethe demister is on.The heater will be turned off automatically inabout 15 to 20 minutes depending on the out-side temperature.
CAUTIONzIt is possible to retract and extend the mirrorsby hand. After retracting a mirror using themirror retractor switch, however, you shouldextend it by using the switch again, not byhand. If you extended the mirror by handafter retracting it using the switch, it wouldnot properly lock in position. As a result, itcould move because of the wind or vibrationwhile you are driving, taking away your rear-ward visibility.NOTE
zBe careful not to get your hands trappedwhile a mirror is moving.zIf you move a mirror by hand or it movesafter hitting a person or object, you may notbe able to return it to its original positionusing the mirror retractor switch. If this hap-pens, push the mirror retractor switch toplace the mirror in its retracted position andthen push the switch again to return the mir-ror to its original position.zWhen freezing has occu
rred and mirrors fail
to operate as intended, please refrain fromrepeated pushing of the retractor switch asthis action can result in burn-out of the mir-ror motor circuits.
Retracting and extending the mir-rors without using the mirror retractor switch
NOTE
zFunctions can be modifi
ed as stated below.
Please consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.•Automatically extend when the operationmode is put in ON, and automaticallyretract when the driver’s door is openedafter the operation mode in put in OFF.•Automatically extend when the vehiclespeed reaches 30 km/h.•Deactivate the automatic extension func-tion.
Heated mirror
*
BK0203201EN.book 9 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Power switch7-10 Starting and driving
7
E00631801079
In order to prevent theft, the Plug-in HybridEV System will not start unless a preregis-tered keyless operation key is used. (Immobi-lizer function)If you are carrying the keyless operation key,you can start the Plug-in Hybrid EV System.
The indicator lamp on the power switch turnsoff.The operation mode cannot be put in OFFunless the electrical parking switch ispressed.Electrical devices such as the audio andaccessory socket can be operated. Can beused when the Ready indicator is off.The indicator lamp on the power switch illu-minates orange.All vehicle’s electrical devices can be oper-ated.The indicator lamp on the power switch illu-minates blue. The indicator lamp turns offwhen the Plug-in Hybrid EV System is oper-ating.
NOTE
zThe heater mirrors can be turned on automat-ically.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point. On vehiclesequipped with Mitsubishi Multi-Communi-cation System (MMCS), screen operationscan be used to make the adjustment. Refer tothe separate owner’s manual for details.
Power switch
CAUTIONzThe indicator lamp (A) will flash orangewhen there is a problem or malfunction inthe keyless operation system. Never drive ifthe indicator lamp on the power switch isflashing orange. Immedi
ately contact a MIT-
SUBISHI MOTORS Authorised ServicePoint.zIf the power switch operation is not smoothand feels like it is stic
king, do not operate the
switch. Immediately contact a MITSUBISHIMOTORS Authorised Service Point.NOTE
zWhen operating the power
switch, press the
switch all the way in. If the switch is notfully pressed, the Plug-
in Hybrid EV System
may not start or the operation mode may notchange. If the power
switch is pressed cor-
rectly, there is no n
eed to hold the power
switch down.zWhen the battery in the keyless operationsystem key has worn
out, and taking the key-
less operation key out of the vehicle, a warn-ing lamp will blink fo
r 5 seconds or warning
display will appear.
Operation mode of the power switch and its function OFFACCON
BK0203201EN.book 10 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Automatic climate control air conditioner8-6 For pleasant driving
8
The settings described above are the factorysettings.The air selection and air conditioningswitches can be customised (function settingchanged), and the automatic switching of out-side air and the air conditioner according tooperating conditions can be changed asdesired.For further information, we recommend youto consult a MITSUBISHI MOTORS Author-ised Service Point.Refer to “Customising the air conditioningswitch” on page 8-8.Refer to “Customising the air selection” onpage 8-7.The driver’s side and the passenger’s sidetemperature can be controlled independently.At this time, the “DUAL” indicator will beshown in the display (A).
zSynchronized modeIf the driver’s side temperature controlswitch is pressed, the passenger’s sidetemperature will also be controlled to thesame setting temperature as the driver’sside.zDual modeIf the passenger’s side temperature con-trol switch is pressed under synchronizedmode, the system will switch to dualmode. In dual mode, the driver’s side andthe passenger’s side temperature can beset separately by using each temperaturecontrol switch.Press the AUTO switch to return to syn-chronized mode.
E00703401808
To change the air selection, simply press theair selection switch.
NOTE
zThe temperature value of air conditioner isswitched in conjunction
with outside temper-
ature display unit of the multi informationdisplay.Refer to “Changing the temperature unit” onpage 6-17.zWhile the engine coolant temperature is low,the temperature of th
e air from the heater
will not change instantly, even if you haveselected warm air with the switch.To p r e v e n t t h e w i n d s c r e e n a n d w i n d o w sfrom fogging up, the ventilator mode will bechanged to “ ” and the blower speed willbe reduced while the system is operating inthe AUTO mode.zWhen you feel that it is hot or cold to the set-ting temperature, it is possible to adjust sothat you can feel more comfortable.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.zWhen the temperature is set to the highest orthe lowest, the air selection and the air condi-tioner will be automatically changed as fol-lows.Also, if the air selec
tion is operated manually
after an automatic changeover, manual oper-ation will be selected.•Quick Heating (When the temperature is setto the highest setting)Outside air will be introduced and the airconditioner will stop.
•Quick Cooling (When the temperature is setto the lowest setting)Inside air will be r
ecirculated and the air
conditioner will operate.
zWhen the air conditioner is set to quick heat-ing, the engine starts
running (except vehi-
cles with electric heater).

Automatic climate control air conditioner
For pleasant driving 8-9
8
On vehicles equipped with MitsubishiMulti-Communication System (MMCS),screen operations can also be used tochange the setting. Refer to the separateowner’s manual for details.
E00702700038
Push the switch to turn off the air condition-ing system.
E00703300031
Each time the MODE switch is pressed, themode changes to the next one in the follow-ing sequence: “ ”
m “ ”
m “ ”
m
“”
m “ ”. The selected mode is shown
in the display (A). (Refer to “Mode selection”on page 8-2.)
E00703901063
When this switch is pressed, the modechanges to the “ ” mode. The indicatorlamp (A) will come on. The selected mode isshown in the display (B). (Refer to “Modeselection” on page 8-2.)
NOTE
zThe factory setting is “Enable automatic airconditioning control”.zWhen the demister switch is pressed, inorder to prevent misting of the windows theair conditioner operates automatically even if“Disable automatic air conditioning control”is set.
OFF switch
MODE switch Demister switch
NOTE
zWhen the demister switch is pressed, the airconditioning system automatically operatesand outside air (as oppos
ed to recirculated
air) is selected. This automatic switchingcontrol is carried out to prevent misting ofthe windows even if “D
isable automatic air
conditioning control” or
“Disable
automatic
air control” is set. (Refer to “Customising theair conditioning switch” on page 8-8, “Cus-tomising the air selec
tion” on page 8-7.)
zWhen the demister switch is pressed, theengine may start running (except vehicleswith electric heater).
BK0203201EN.book 9 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Air purifier8-12 For pleasant driving
8
Use of any other refrigerant or lubricant willcause severe damage which will result in theneed to replace your vehicle’s entire air con-ditioning system. New regulations in supportof the Australian Government’s Ozone Pro-tection and Synthetic Greenhouse Gas Man-agement Act 1989 became effective inJanuary 2005. To ensure your vehicle servic-ing and repairs conform with requirements,the air conditioning system should beinspected and maintained by a MITSUBISHIMOTORS Authorised Service Point.The air conditioner should be operated for atleast five minutes each week, even in coldweather. This is to prevent poor lubrication ofthe compressor internal parts and to maintainthe air conditioner in the best operating con-dition.
E00708400718
An air filter has been incorporated into thisair conditioner so that dirt and dust arecleaned from the air.Replace the air filter periodically as its abilityto clean the air will be reduced as it collectspollen and dirt. For the maintenance interval,refer to the “SERVICE BOOKLET”.
E00735401045
Yo u c a n r u n t h e a i r c o n d i t i o n e r i n a d v a n c e o fusing the vehicle.For details, refer to “Remote Climate Con-trol” on page 3-17.
E00733901059
When heating, the engine starts runningbecause the heating system uses the heat ofengine coolant.On vehicles with electric heater, it candecrease the number of times engine startingbecause electrical power stored in the drivebattery is also used when heating.
E00708503390
The audio system can only be used when theoperation mode of the power switch is in ONor ACC.
During a long period of disuse Air purifier
NOTE
zOperation in certain c
onditions such as driv-
ing on a dusty road and frequent use of theair conditioner can lead to reduction of ser-vice life of the filter. When you feel that theairflow is lower than normal or when thewindscreen or windows start to fog up easily,replace the air filter.We r e c o m m e n d y o u t o h a v e i t c h e c k e d .
Remote Climate Control Heating
AM/FM radio/CD player
*
NOTE
zTo l i s t e n t o t h e a u d i o s y s t e m w h i l e t h e P l u g -in Hybrid EV system is
not operating, put the
operation mode of the power switch in ACC.If the operation mode of the power switch isleft in ACC, the accessory power will auto-matically turn off after a certain period oftime and you will no longer be able to usethe audio system. The accessory powercomes on again if the operation mode of thepower switch is operated with is in the ACC.Refer to “ACC power auto-cutout function”on page 7-11.zIf a cellular phone is used inside the vehicle,it may create noise from the audio equip-ment. This does not mean that anything iswrong with your audio equipment. In such acase, use the cellular phone at a place as faraway as possible from the audio equipment.zIf foreign objects or wate
r get into the audio
equipment, or if smoke or a strange odourcomes from it, immediately turn off theaudio system. We recommend you to have itchecked. Never try to repair it by yourself.Av o i d c o n t i n u o u s u s a g e w i t h o u t i n s p e c t i o nby a qualified person.
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Handling of Discs8-16 For pleasant driving
8
zFingerprints or other marks on the readsurface of the disc may result in its con-tent being more difficult to read. Whenholding the disc, grip both edges, or oneedge and the centre hole, in order that theread surface is not touched.zDo not affix paper or stickers, or other-wise damage the disc.zDo not forcefully insert a disc if another isalready within the device. This can resultin damage to discs, or malfunction.zPeriodically clean the read surface of thedisc. When cleaning, do not wipe in a cir-cular motion. Instead, wipe gently out-wards from the centre of the disc to theouter edge.zNew discs may have burring around theouter edge or in the hole in the centre.Ensure you check for these. If there areburrs, these may lead to faulty operation,therefore ensure these are removed.zWhen not using discs, ensure these arekept in cases, and stored out of direct sun-light.
zIf discs are not going to be used for a longperiod of time, remove these from theproduct.
In cold environments such as in mid-winterwhen the interior of the vehicle is cold, turn-ing the heater on and immediately trying touse the product may cause condensation(water droplets) to form on the disc and inter-nal optical components, and this may preventthe product from operating correctly.In these conditions, remove the disc, and waita short time before use.Actions such as unauthorised reproduction,broadcast, public performance, or rental ofdiscs that comprise other than personal useare prohibited by law.
E00736001035
The following marks are printed on the disclabel, package, or jacket.
zPlayback of discs other than thosedescribed in “Types of Disc That Can BePlayed Back” is not guaranteed.z8 cm discs may not be used.zDo not insert irregularly-shaped discs (forexample, heart-shaped), as these mayresult in malfunction. Additionally, discsthat have transparent portions may not beplayed back.
Important Points on HandlingCleaningImportant Points on Storage
Disc Playback EnvironmentCopyrightTy p e s o f D i s c T h a t C a n B e Played Back
Ty p e
Size
Maxi-mum playback time
Com-ments
CD-DA 12 cm 74 minutes —CD-TEXT 12 cm 74 minutes —CD-R/RW 12 cm — •Disc
contain-ing MP3 files
Discs That May Not Be Played Back
BK0203201EN.book 16 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Emergency starting
For emergencies 9-3
9
2. Turn off all lamps, heater and other elec-trical loads.3. Set the parking brake firmly on each vehi-cle. Set the gear of another vehicle in “P”(PARK) position (with A/T) or in “N”(Neutral) position (with M/T) and stop theengine.4. Open the bonnet, remove the fuse coverof the main fuse block.Refer to “Bonnet” on page 11-3 and“Fuses: Engine compartment” on page11-16.
5. Open the cover of the jumper cable termi-nal in the main fuse block.
6. Connect one end of one jumper cable to the jumper cable terminal (A) of yourvehicle, and the other end to the posi-tive (+) terminal of the booster battery(B).Connect one end of the other jumper cable to the negative (-) terminal of thebooster battery, and the other end tothe designated ground location of yourvehicle.
WA R N I N GzWhen connecting the jumper cable, stopthe engine in another vehicle. Otherwise,the cables or your cl
othes may be caught
by the fan or drive belt and personalinjury could result.zThe cooling fan turns on and off depend-ing on the coolant temperature. Do notbring your hands close to the fan while theengine is running or Plug-in Hybrid EVSystem is operating.
NOTE
zYo u c a n n o t r e s c u e o t h e
r vehicle’s discharged
battery by connecting jumper cables usingthis jumper cable terminal.
BK0203201EN.book 3 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分