2014 MITSUBISHI OUTLANDER light

10Names and functions of parts
Names and functions of parts
Replacing the battery
Use your fi
ngernail to press tab A on
the battery case at the backside of the
remote control. While pressing tab A in
the direction shown in (1), pull the battery
case out as shown in (2)NOTE
· When disposing of the lithium battery, apply
insulating tape and dispose of the battery in
accordance with applicable local regulations. Place a new battery in the battery case
with its positive side facing up
New battery(positive side)
mc4380
Before using the remote controlThe remote control comes with a battery
installed.
There is an insulation sheet to prevent
the battery from discharging. Remove this
insulation sheet before using the remote
control.
mb073
Insulation sheet
Operating instructions
When using the remote control to operate
the system, aim the remote control at the
remote control sensor.
mc4394
Remote control sensorNOTE
· Do not disassemble or drop the remote control, and
do not subject the remote control to any physical
shock.
· Do not place any heavy objects on top of or sit on the remote control.
· If the remote control sensor is exposed to direct sunlight or other strong light, it may stop functioning
properly or stop operating at all. In this situation,
block out the light.

Supported disc types21
Supported disc typestion, or rental of discs without expressed
written permission is prohibited by law.
· This product incorporates copyrighted technologies. Macrovision Corporation
and other copyright holders are protect-
ed by US patents and other intellectual
property rights protections.
· Permission to use this copyrighted technology must be obtained from Mac-
rovision Corporation. Without special
permission from Macrovision Corpora-
tion, use of this technology is restricted
to home or private use.
any burrs using a ballpoint pen or other
implement.
Precautions for storage
· When not using discs, always put them in their cases and keep them out of
direct sunlight.
· Always remove discs from the system when not using them for an extended
period.
Disc playing environment
· Extreme changes in temperature may cause moisture to form on the discs or
inside of the system, preventing normal
operation. Such cases include turning
on the heater in the vehicle during the
extreme cold of midwinter.
In such cases, eject the disc and wait a while before using the system.
· Do not use cracked or warped discs.
· Do not use heart shaped or other spe- cial shaped discs, or partially transpar-
ent discs.
· Do not use 8 cm CD adapters. Doing so could cause a malfunction.
Copyright information
· The copying, broadcast, public exhibi-
Handling of discs
Proper handling of discsPrecautions for handling
· Dirt or fi ngerprints on the disc surface
could make the disc unreadable. Do not
touch the disc surface when handling
the disc. Always hold the disc at the
outer edges, or at the center hole and
the outer edge.
· Do not apply labels or stickers to the disc and do not scratch the disc.
· Do not force another disc into the disc loading slot when there is already a disc
inserted. Doing so could damage the
discs and cause malfunctions.
Care and maintenance
· Periodically clean the disc surface. Clean the disc with a soft cloth. Gently
wipe from the center hole to the outer
edge. Do not wipe in a circle.
· A new disc may still have burrs on its periphery and center hole, so be sure to
check for such burrs.
Using a disc that has burrs can cause a malfunction, so be sure to remove

27
Basic operations
Basic operations
To adjust display attributes
Press the DISP
button
Display attribute adjustment items (BRIGHT, CONTRAST, COLOR, TINT) are
displayed on the screen.
PICTURE CONTROL
BRIGHT
CONTRAST
TINT
G
R
COLOR
Move the JOYSTICK
up and down to select the item to be
adjusted, then move the JOYSTICK
left and right to make
the adjustment
BRIGHT
Moving right increases brightness.
Moving left decreases brightness.
CONTRAST
Moving right increases the contrast.
Moving left decreases the contrast.
COLOR
Moving right darkens the color.
Moving left lightens the color.
TINT
Moving right increases the green hue.
Moving left increases the red hue.
After making adjustments, wait a while and the display adjustment items will disappear.
NOTE
· Brightness can be adjusted for daytime (LIGHT OFF) and nighttime (LIGHT ON) respectively
To adjust display attributes and screen size
mc4384

Troubleshooting
52
Troubleshooting
Problem Cause Action to take
The wireless
headphones do not
work. The wireless
headphone power is
switched OFF, or the
volume is turned all
the way down.Check the wireless
headphone power and
volume.
The wireless
headphone battery is
run down. Replace the battery.
The disc does not
play. The disc is inserted
with the disc surface
facing up.Insert the disc with the
disc surface facing
down.
The disc is dirty or
scratched. Check the disc.
The inserted disc is
not supported by the
system.
The recording format
is not supported by
the system. Check the operation
of the recording
equipment.
Problem
Cause Action to take
The power does not
come on. The ignition key is in
the OFF position.Turn the ignition key
to the ACC or ON
positions.
The display remains
closed. Open the display or
press the POWER
button.
The remote control
does not work. The remote control
battery is run down.Replace the battery.
The system remote
control sensor is in
strong light, such as
direct sunlight. Avoid using the
system in direct
sunlight.
The remote control
is not aimed at the
system remote control
sensor. Aim the remote control
at the system remote
control sensor.
The screen is dark. The brightness is not properly adjusted.Make the necessary
adjustments.
The color is bad. The color or tint is not properly adjusted.

Handling of discs55
Handling of discs
• Clean the disc with a soft
cloth, wiping from the center
hole to the outer edge. Do not
use benzine, record cleaning
spray, anti-static agents, or
chemically treated tissues.
Doing so could damage the
disc surface.• Discs are made of plastic. To prevent discs from warping,
always put them in their cases
and keep them out of direct
sunlight.• Discs turn at high speeds, so do not use cracked or warped
discs. Doing so could cause a
malfunction or breakdown.• The system may not function properly when driving on rough roads, due to the severe vibrations.• If foreign matter should get into the system ( through the disc loading slot, for example) contact your authorized
dealer.
Using the system in this state could cause a malfunction or breakdown.
• Using heart shaped, octagonal, or other special shaped discs,
or partially transparent discs
could cause a malfunction.• A new disc may still have burrs on its periphery and
center hole, so be sure to
check for such burrs. Using
a disc that has burrs can
cause a malfunction, so be
sure to remove any burrs
using a ballpoint pen or other
implement.• Do not touch the disc surface (the shiny, rainbow colored
side) when handling the disc.
Always hold the disc at the
outer edges, or at the center
hole and the outer edge. A
dirty or scratched disc could
cause a malfunction.• Do not apply labels or stickers to the disc and do not scratch
the disc.