2014 MERCEDES-BENZ CLS brake light

RACESTART
Important safety notes
iObserve the safety notes for the SPORT
handling mode(Ypage 70).
RACESTART is intended solely for activation
on dedicated race circuits.
RACE START enables optimal acceleration
fromastandingstart.The precondition for
this isasuitable high-grip road surface.
iRACE START is only available in AMG
vehicles.
Conditions for activation
You can activateRACE START if:
Rthe doors are closed.
Rthe engine is runningand it has reached an
operating temperature of approximately
176‡(80 †). This is the case when the
engine oil temperature in the multifunction
display stops flashing.
RSPORT handling mode is activated.
(Ypage 70)
Rthe steeringwheel is in the straight-ahead
position
Rthe vehicle is stationary and the brake
pedal is depressed (left foot).
Rthe transmission is in positionD.
Activating RACE START
XDepress the brake pedal with your left foot
and keep it depressed.
XTurn the drive program selector clockwise
(Ypage 159) until theRSlamp lights up.
TheRACE START Confirm: Paddle UP
Cancel: Paddle DOWNmessage appears
in the multifunction display.
iIf the activation conditions are no longer
fulfilled, RACE START is canceled. The
START Canceledmessage appears in the
multifunction display.
XTo cancel: pull the left steeringwheel
paddle shifter (Ypage 160).
or
XTo confirm: pull the right steeringwheel
paddle shifter (Ypage 160).
TheRACE START Available Depress
gas pedalmessage appears in the
multifunction display.
iIf you do not depress the accelerator
pedal fully within two seconds, RACE
START is canceled. TheRACE START Not
Possible See Operator's Manual
message appears in the multifunction
display.
XFully depress the accelerator pedal.
The engine speed rises to approximately
3,500 rpm.
TheRACE START Release brake to
startmessage appears in the
multifunction display.
iIf you do not release the brake pedal
within five seconds, RACE START is
canceled. TheRACE START Canceled
message appears in the multifunction
display.
XTake your foot off the brake, but keep the
accelerator pedal depressed.
The vehicle pulls away at maximum
acceleration.
TheRACESTARTActivemessage appears
in the multifunction display.
RACE START is deactivated when the vehicle
reachesaspeed of approximately 30 mph
(Canada: 50 km/h).Drive programS+is
activated. SPORT handling mode remains
activated.
RACE START is deactivated immediately if
you release the accelerator pedal during
RACE START or if any of the activation
conditions are no longer fulfilled. TheRACE
START Not Possible See Operator's
Manualmessage appears in the multifunction
display.
iIf RACE START is used repeatedly within
ashort period of time, it is only available
188Driving systems
Driving and parking

indicator lamp goes out and BlindSpot Assist
is operational.
Ifavehicle is detected within the monitoring
rangeofBlindSpot Assist at speeds above
20 mph (30 km/h), warninglampon the
correspondingside lightsupred. This warning
is always emitted whenavehicle enters the
blind spot monitoring rangefrom behind or
from the side.When you overtakeavehicle,
the warning only occurs if the difference in
speed is less than7mph (12km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event,Blind Spot
Assist is no longer active.
The brightness of the indicator/warning
lamps is adjusted automatically according to
the ambient light.
Collision warning
Ifavehicle is detected in the monitoring range
of Blind Spot Assist and you switchonthe
correspondingturn signal,adouble warning
tonesounds. Red warning lampflashes. If
the turn signal remains on, vehicles detected
are indicated by the flashing of red warning
lamp.There are no further warning tones.
Switching on Blind Spot Assist
XMake sure that Blind Spot Assist
(Ypage 228) is activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Lane Keeping Assist
Important safety notes
GWARNING
Lane Keeping Assist may not always clearly
recognizelane markings.
In this case, Lane Keeping Assist may:
Rgive an unnecessary warning
Rnot giveawarning
There isarisk of an accident.
Always pay particular attention to the traffic
situation and stay in lane, in particular if
warned by Lane Keeping Assist.
GWARNING
The Lane Keeping Assist warning does not
return the vehicle to the original lane. There
isarisk of an accident.
You should always steer, brake or accelerate
yourself, in particular if warned by Lane
Keeping Assist.
If you fail to adapt your driving style, Lane
Keeping Assist can neither reduce the risk of
an accident nor override the laws of physics.
Lane Keeping Assist cannot take into account
the road, traffic and weather conditions. Lane
Keeping Assist is merely an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
The Lane Keeping Assist does not keep the
vehicle in the lane.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to
insufficient illumination of the road, or due
to snow, rain, fog or spray
Rthere is glare, e.g. from oncomingtraffic,
the sun or reflections (e.g. when the road
surface is wet)
Rthe windshield is dirty, fogged up, damaged
or covered, for instancebyasticker, in the
vicinity of the camera
Rthere are no, several or unclear lane
markings foralane, e.g. in areas with road
construction work
Rthe lane markings are worn away,dark or
covered up, e.g. by dirt or snow
Driving systems209
Driving and parking
Z

The brightness of the indicator/warning
lamps is adjusted automatically accordingto
the ambient light.
Visual and acoustic collision warning
If you switch on the turn signals to change
lanes andavehicle is detected in the side
monitoring range, you receiveavisual and
acoustic collision warning. You then hear a
double warning toneand red warning
lampflashes. If the turn signal remains on,
detected vehicles are indicated by the
flashing of red warning lamp.There are no
further warning tones.
Course-correcting brake application
GWARNING
Acourse-correctingbrake application cannot
alwayspreventacollision. There isarisk of
an accident.
Always steer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
you or makesacourse-correcting brake
application. Always maintainasafe distance
at the sides.
If Active Blind Spot Assist detectsarisk of a
lateral collision in the monitoring range, a
course-correcting brake application is carried
out. This is meant to assist you in avoiding a
collision.
Ifacourse-correcting brake application
occurs, red warning lampflashes in the
exterior mirror andadual warning tone
sounds. In addition, the display shown in the
lower image appears in the multifunction
display.
In very rare cases, the system may make an
inappropriate brake application. An
inappropriate course-correcting brake
application may be interrupted at any time if
you steer slightly in the opposite direction or
accelerate, for example.
The course-correcting brake application is
available in the speed range between
20 mph (30 km/h) and 120 mph (200 km/h).
Either no braking application, oracourse-
correcting brake application adapted to the
driving situation occurs if:
Rthere are vehicles or obstacles, e.g. crash
barriers, located on both sides of your
vehicle.
Ravehicle approaches you too closely at the
side.
Ryou have adoptedasporty driving style with
high cornering speeds.
Ryou clearly brake or accelerate.
Radriving safety system intervenes, e.g.
ESP®or PRE-SAFE®Brake.
RESP®is switched off.
Raloss of tire pressure oradefectivetire is
detected.
Switching on Active Blind Spot Assist
XMake sure that the radar sensor system
(Ypage 232) and Active Blind Spot Assist
(Ypage 228) are activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Driving systems213
Driving and parking
Z

Rthe roadisnarrow and winding
Rthere arestrong shadows castonthe lane
If no vehicle is detected in the adjacent lane
and there are broken lane markings detected,
no lane-correcting brake application is made.
Warning vibration in the steering wheel
Awarning may be given ifafront wheel
passes overalane marking. It will warn you
by means of intermittent vibration in the
steering wheel for up to 1.5 seconds.
Lane-correcting brake application
GWARNING
Alane-correcting brake application cannot
always bring the vehicle back into the original
lane. There isarisk of an accident.
Always steer, brake or accelerate yourself,
especially if Active Lane Keeping Assist warns
you or makesalane-correcting brake
application.
GWARNING
Active Lane Keeping Assist does not detect
traffic conditionsorroad users. In very rare
cases, the system may make an inappropriate
brake application, e.g. after intentionally
driving overasolid lane marking. There is a
risk of an accident.
An inappropriate brake application may be
interrupted at any time if you steer slightly in
the opposite direction. Always make sure that
there is sufficient distance on the side for
other traffic or obstacles.
If you leave your lane, under certain
circumstances the vehicle will brake briefly
on one side. This is meant to assist you in
bringing the vehicle back to the original lane.
Ifalane-correcting brake application occurs,
displayappears in the multifunction
display.
This function is available in the range between
40 mph and 120 mph (60 km/h and
200 km/h).
Alane-correcting brake application can only
be made after driving overasolid,
recognizable lane marking. Before this, a
warning must be given by means of
intermittent vibration in the steering wheel.
In addition,alane with lane markings on both
sides must be recognized. The brake
application also slightly reduces vehicle
speed.
iAfurther lane-correcting brake
application can only occur after your
vehicle has returned to the original lane.
No lane-correcting brake application occurs
if:
Ryou clearly and actively steer, brake or
accelerate.
Ryou cut the corner onasharp bend.
Ryou have switched on the turn signals.
Radriving safety system intervenes, e.g.
ESP®,PRE-SAFE®Brake or Active Blind
Spot Assist.
Ryou have adoptedasporty driving style with
high cornering speeds or high rates of
acceleration.
RESP®is switched off.
Rthe transmission is not in positionD.
Raloss of tire pressure oradefective tire has
been detected and displayed.
Active Lane Keeping Assist may is unable to
detect other road or traffic conditions. An
inappropriate brake application may be
interrupted at any time if you:
Driving systems215
Driving and parking
Z

Rsteer slightly in the opposite direction
Ruseaturn signal
Rclearly brake or accelerate
Alane-correcting brakeapplicationis
interrupted automatically if:
Radrivingsafetysystem intervenes,e.g.
ESP®,PRE-SAFE®Brake or ActiveBlind
Spot Assist.
Rlane markings can no longer be recognized.
Switching on Active Lane Keeping Assist
XSwitch on ActiveLane KeepingAssist using
the on-board computer;todoso, select
StandardorAdaptive(Ypage 229).
If you drive at speeds above 40 mph
(60 km/h) and lane markings are detected,
the lines in the assistancegraphicsdisplay
(Ypage 227)are shown in green.Lane
KeepingAssist is ready for use.
IfStandardis selected, no warning
vibration occurs if:
Ryou have switched on the turnsignals.In
thisevent, the warnings aresuppressed
foracertainperiodoftime.
Radriving safety systemintervenes, such
as ABS, BAS or ESP®.
IfAdaptiveis selected, no warning
vibrationoccurs if:
Ryouhaveswitched on the turnsignals.In
thisevent, the warnings aresuppressed
foracertainperiodoftime.
Radriving safety systemintervenes, e.g.
ABS, BAS or ESP®.
Ryouaccelerate hard, e.g.kickdown.
Ryou brakehard.
Ryou steer actively, e.g. swervetoavoid
an obstacle or change lanes quickly.
Ryou cut the corner onasharp bend.
In order that you are warnedonly when
necessary and in good timeifyou cross the
lane marking, the system recognizes certain
conditions and warns you accordingly.
The warning vibration occurs earlier if:
Ryou approach the outer lane marking on a
bend.
Rthe road has very wide lanes, e.g. a
highway.
Rthe system recognizes solid lane markings.
The warning vibration occurs later if:
Rthe road has narrow lanes.
Ryou cut the corner onabend.
216Driving systems
Driving and parking

GWARNING
If you deactivate ESP®,ESP®no longer
stabilizes the vehicle. There is an increased
risk of skidding and an accident.
Only deactivate ESP®in the situations
described in the following.
It may be best to deactivate ESP®in the
following situations:
Rwhen using snow chains
Rin deep snow
Ron sand or gravel
Activating/deactivating ESP®on AMG
vehicles (Ypage70).
For further information about ESP®,see
(Ypage68).
XStart the engine.
XPress the\norbutton on the
steering wheeltoselect theDriveAssist
menu.
XPress theorbutton to select
ESP.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
ESP®is deactivated if the warning lamp
in the instrument cluster lights up
continuously when the engine is running.
If thewarning lamp and the
warning lamp are lit continuously,ESP®is not
available due toamalfunction.
Observe the information on warning lamps
(Ypage269).
Observe the information on display messages
(Ypage238).
Activating/deactivating PRE-SAFE®
Brake
PRE-SAFE®Brake is only available in vehicles
with DISTRONIC PLUS.
XPress\noron the steering wheel
to select theDriveAssistmenu.
XPress theorbutton to select
PRE-SAFEBrake.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
When PRE-SAFE®Brake is deactivated, the
assistance graphic showsthe
symbol in
the multifunction display.
For more information on PRE-SAFE®Brake,
see (Ypage72).
Activating/deactivating ATTENTION
ASSIST
XPress\noron the steering wheel
to select theDriveAssistmenu.
XPressorto selectAttention
Assist.
XPress thebutton.
The current selection is displayed.
XTo activate/deactivate:press the
button again.
When ATTENTION ASSIST is deactivated, the

symbol and OFF appear in the
multifunction display in the assistance
display when the engine is running.
For further information about ATTENTION
ASSIST, see (Ypage203).
Activating/deactivating Blind Spot
Assist
XPress\noron the steering wheel
to select theDriveAssistmenu.
XPress theorbutton to select
Blind Spot Asst.
228Menus and submenus
On-board computer and displays

switch-off exterior lighting are on, the
following light up:
RParking lamps
RLow-beam headlamps
RDaytime running lamps
RSide marker lamps
RSurround lighting in the exterior mirrors
Activating/deactivating the interior
lighting delayed switch-off
If you activate theInterior Lighting
Delayfunction,the interior lighting remains
on for 20seconds after you remove the
SmartKey from the ignition lock.
XPress the\norbutton on the
steering wheel to select theSett.menu.
XPress theorbutton to select the
Lightssubmenu.
XPressto confirm.
XPressorto select theLight.
Delayfunction.
When theInterior Lighting Delay
function is activated, the vehicle interior is
displayed in red in the multifunction
display.
XPress thebutton to save the setting.
Vehicle
Activating/deactivating the automatic
door locking mechanism
XPress the\norbutton on the
steering wheel to select theSett.menu.
XPressorto select theVehicle
submenu.
XPressto confirm.
XPressorto select theAuto.
Door Locksfunction.
When theAutomaticDoorLockfunction
is activated, the vehicle doors are displayed
in red in the multifunction display.
XPress thebutton to save the setting.
If you activate theAutomatic Door Lock
function,the vehicle is centrally locked above
aspeed of around9mph (15 km/h).
For further information on the automatic
locking feature, see (Ypage 83).
Activating/deactivating the acoustic
locking verification signal
If you switch on theAcousticLockfunction,
an acoustic signal sounds when you lock the
vehicle.
XPress the\norbutton on the
steering wheel to select theSett.menu.
XPressorto select theVehicle
submenu.
XPressto confirm.
XPress theorbutton to select the
Acoustic Lockfunction.
If theAcousticLockfunction is activated,
thesymbol in the multifunction
displaylights up red.
XPress thebutton to save the setting.
Activating/deactivating the radar sensor
system
XPress the\norbutton on the
steering wheel to select theSett.menu.
XPressorto select theVehicle
submenu.
XPressto confirm.
XPress theorbutton to select
Radar Sensor (See Oper. Manual):.
You will see the selected setting:Enabled
orDisabled.
XPress thebutton to save the setting.
The following systems are switched off when
the radar sensor system is deactivated:
RDISTRONIC PLUS (Ypage 177)
RBAS PLUS (Ypage 67)
RPRE-SAFE®Brake (Ypage 72)
RBlind Spot Assist (Ypage 207)
RActive Blind Spot Assist (Ypage 211)
232Menus and submenus
On-board computer and displays

Safety systems
Display messagesPossible causes/consequences andSolutions

Currently
Unavailable See
Operator's Manual
ABS (Anti-lock Braking System), ESP®(Electronic Stability
Program), BAS (Brake Assist), PRE-SAFE®,the HOLD function and
hill start assist are temporarily unavailable.
BAS PLUS and PRE-SAFE®Brake may also have failed.
In addition, the, andwarning lamps light up in
the instrumentcluster.
ATTENTIONASSIST is deactivated.
Possible causes are:
Rself-diagnosis is not yet complete.
Rthe on-board voltage may be insufficient.
GWARNING
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XCarefully driveasuitable distance, making slight steering
movements, ataspeed above 12 mph (20 km/h).
If the displaymessage disappears, the functions mentioned
above are available again.
If the displaymessage continues to be displayed:
XDrive on carefully.
XVisitaqualified specialist workshop.

Inoperative See
Operator's Manual
ABS,ESP®,BAS,PRE-SAFE®,the HOLD function and hill start
assist are unavailable due toamalfunction.
The(USA only)/
(Canada only),, and
warning lamps in the instrumentcluster also light up.
ATTENTION ASSISTisdeactivated.
GWARNING
The brakesystem continues to function normally, but without the
functionslisted above. The wheels could therefore lock if you
brakehard, for example.
238Display messages
On-board computer and displays