Securing the vehicle on slight downhil
lgradients
X On light downhill gradients: place
chocks or othe rsuitabl eitem sinf ront of
the wheel softhe front and rea raxle.
Raisin gthe vehicle G
WARNING
If yo udon ot positio nthe jack correctly at the
appropriate jackingp oint of the vehicle, the
jack could tip over with the vehicle raised.
There is arisk of injury.
Only position the jack at the appropriate
jackingp oint of the vehicle. The base of the
jack must be positioned vertically, directly
under the jackingp oint of the vehicle.
! The jack is designed exclusively for
jackingupt he vehicle at the jackingp oints.
Otherwise, your vehicle could be damaged.
The following must be observed when raising
the vehicle:
R to raise the vehicle, only use the vehicle-
specific jack that has been tested and
approved by Mercedes-Benz. If used
incorrectly, the jack could tip over with the
vehicle raised.
R the jack is designed only to raise and hold
the vehicle for ashort time while awheel
is being changed. It is not suited for
performing maintenancew ork under the
vehicle.
R avoid changing the wheel on uphill and
downhill slopes. R
before raising the vehicle, secure it from
rolling away by applying the parking brake
and insertingw heel chocks. Never
disengage the parking brake while the
vehicle is raised.
R the jack must be placed on afirm, flat and
non-slip surface. On aloose surface, a
large, load-bearing underlay must be used.
On aslippery surface, anon-slip underlay
must be used, e.g. rubber mats.
R do not use wooden blocks or similar
objectsasaj ack underlay.O therwise, the
jac kw ill not be able to achiev eits load-
bearin gcapacity due to the restricted
height.
R mak esure that the distanc ebetween the
underside of the tires and the groun ddoes
not exceed 1. 2in(3cm).
R never place your hands and feet under the
raised vehicle.
R never lie under the raised vehicle.
R never start the engine when the vehicle is
raised.
R never open or clos eadoor or the trunk lid
when the vehicle is raised.
R mak esure that no persons are present in
the vehicle when the vehicle is raised. X
Usin glug wrench 001A,loosen the bolt son
the wheel you wish to change by about one
full turn. Do not unscrew the bolts
completely. Changin
gawheel
359Wheels and tires Z
X
Position jack 0024at jacking point 0010. Example
X
Make sure the foot of the jack is directly
beneath the jacking point.
X Turn crank 0021clockwise until jack 0024sits
completely on jacking point 0010and the
base of the jack lies evenly on the ground.
X Turn crank 0021until the tire is raised a
maximum of 1.2 in (3 cm) off the ground. Removing
awheel !
AMG vehicles: during removaland
repositioning of the wheel, the wheel rim
can strike the ceramic-brake disc and
damage it. Therefore, take precautions and
get asecond perso ntoassist you.
Alternatively, you can use asecond
alignment bolt.
! Do not place wheel bolts in sand or on a
dirty surface. The bolt and wheel hub
threads could otherwise be damaged when
you screw them in. X
Unscrew the uppermost wheel bolt
completely.
X Screw alignment bolt 001Ainto the thread
instead of the wheel bolt.
X Unscrew the remaining wheel bolts fully.
X Remove the wheel.
Mounting anew wheel G
WARNING
Oiled or greased wheel bolt sordamaged
wheel bolts/hub threads can cause th ewheel
bolt stoc omeloose .Asa result, you could
lose awheel while driving. There is arisk of
accident.
Never oil or grease wheel bolts. In the event
of damage to the threads, contact aqualified
specialist workshop immediately.H ave the
damage dwheel bolt sorhub threads
replaced/renewed. Do no tcontinue driving. 360
Changing
awheelWheels and tires
