2014 MERCEDES-BENZ CLA set clock

Automatic locking feature
XTo deactivate:press and hold button
for about five seconds until a tone sounds.
XTo activate:press and hold buttonfor
about five seconds until a tone sounds.
iIf you press one of thetwo buttons and
do not hear a tone, the relevant setting has
already been selected.
The vehicle is locked automatically when the
ignitionis switched on and the wheels are
turning.
You could therefore lock yourselfout if:
Rthe vehicle is being pushed.
Rthe vehicle is being towed.
Rthe vehicle is on a roller dynamometer.
You can also switch the automatic locking
function on and off using the on-board
computer (Ypage 208).
Unlocking the driver's door
(mechanical key)
If the vehicle can no longer be unlocked with
the SmartKey, use the mechanical key.
If you use the mechanical key to unlock and
open the driver's door, the anti-theftalarm
system will be triggered (Ypage 70).
XTake the mechanical key out of the
SmartKey (Ypage 73).
XInsert the mechanical key into the lock of
the driver's door as far as it will go.
XTurn the mechanical key counter-clockwise
to position.
The door is unlocked.
XTurn the mechanical key back and remove
it.
XInsert the mechanical key into the
SmartKey.
Locking the vehicle (mechanical key)
If the vehicle can no longer be locked with the
SmartKey, use the mechanical key.
XOpen the driver's door.
XClose the front-passenger door, the rear
doors and the trunk lid.
XPress the locking button (Ypage 78).
XCheck whether the locking knobs on the
front-passenger door and the rear doors
are still visible. Press down the locking
knobs manually, if necessary (Ypage 77).
XClose the driver's door.
XTake the mechanical key out of the
SmartKey (Ypage 73).
XInsert the mechanical key into the lock of
the driver's door as far as it will go.
Doors79
Opening and closing
Z

XBrake lamp/rear fog lamp/backup
lamp:remove the corresponding bulb from
the bulb holder.
XInsert the new bulb into the bulb holder.
XTurn signal lamp:lightly press the bulb
into the bulb holder, turn it counter-
clockwise and remove it from bulb holder.
XInsert the new bulb into the bulb holderand
turn it clockwise.
XReinsert the bulb holderand engage on
retaining clips.
XRe-establish contact with the connector.
XClose the side trim panel (Ypage 114).
Windshieldwipers
Switching the windshield wipers on/
off
!Do not operate the windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
that has collected on the windshield can
scratch the glass if wiping takes place when
the windshield is dry.
If it is necessary to switch on the windshield
wipers in dry weather conditions, always
use washer fluid when operating the
windshield wipers.
!If the windshield wipers leave smears on
the windshield after the vehicle has been
washed in an automatic car wash, wax or
other residues may be the reason for this.
Clean the windshield using washer fluid
after washing the vehicle in an automatic
car wash.
Combination switch
Windshield wiper off

Intermittentwipe, low (rain sensor
set to low sensitivity)
Intermittentwipe, high (rain sensor
set to high sensitivity)
Continuous wipe, slow
Continuous wipe, fast
Single wipe/To wipe the
windshield using washer fluid
XSwitch on the ignition.
XTurn the combination switch to the
corresponding position.
!Vehicles with a rain sensor: if the
windshield becomes dirty in dry weather
conditions, the windshield wipers may be
activated inadvertently. This could then
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
Vehicles witharain sensor:in the
or
position, the appropriate wiping
frequency is automatically set according to
the intensity of the rain. In theposition,
the rainsensor is more sensitive than in
the
position, causing the windshield
wipers to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic
conditions.Replace the wiper blades twice a
year, ideally in spring and fall.
Windshield wipers115
Lights and windshield wipers
Z

!Activates/deactivates air-recirculation mode (Ypage 131)
Sets the airflow (Ypage 128)
Switches cooling with airdehumidification on/off (Ypage 125)
Switches the rear window defroster on/off (Ypage 130)
Notes on using climate control
Automatic climate control
The following contains notes and
recommendations on optimum use of the
automatic climate control.
RSwitch on the air-conditioning system by
turning control knobclockwise to the
desired position (except position0).
RSet the temperature to 72 ‡ (22 †).
RRecommendation for preventing
fogged up windows with low outside
temperatures or rain:switchon for
the air distribution and switchand
off if possible (Ypage 128).
In air-recirculation mode, switchoff
(Ypage 131).
Set airflow controlto a setting between
3and6(Ypage 128).
RRecommendation for rapid cooling or
heating of the vehicle interior:briefly set
airflow controlto a setting between3
and6(Ypage 128).
RRecommendation for a constant
vehicle interior temperature:set airflow
controlto a setting between1and3
(Ypage 128).
RRecommendation for air distribution in
the winter:setand
(Ypage 128).
Recommendation for air distribution in
the summer:setorand
(Ypage 128).
ROnly use the "Windshield defrosting"
function briefly until the windshield is clear
again.
ROnly use air-recirculation mode briefly, e.g.
if there are unpleasant outside odors or
when in a tunnel. The windows could
otherwise fog up, since no fresh air is drawn
into the vehicle in air-recirculation mode.
RVehicles with COMAND:if you change the
settings of the climate control system, the
climate status display appears for three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the currentsettings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off, the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 140).
122Overview of climate control systems
Climate control

ROnly available on vehicles for Canada:
use the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
residual heat function can only be activated
or deactivated with the ignition switched
off.
RVehicles with COMAND:if you change the
settings of the climate control system, the
climate status display appears for three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the currentsettings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off, the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 140).
Operating the climate control
systems
Switching climate control on/off
Points to observe before use
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could fog up.
Therefore, switch off climate control only
briefly
Activating/deactivating
Automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo switch on:turn controlclockwise to
the desired position (except position0)
(Ypage 121).
XTo switch off:turn controlcounter-
clockwise to position0(Ypage 121).
Dual-zone automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up. Airflow and air distribution are set to
automatic mode.
or
XPress thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored.
XTo deactivate:press thebutton.
The indicator lamp in thebutton lights
up.
iDual-zone automatic climate control:
switch on climate control primarily using
thebutton.
Activating/deactivating cooling with
air dehumidification
Points to observe before use
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
only deactivate the "Cooling with air-
dehumidification" function briefly.
The cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and
Operating the climate control systems125
Climate control

Problems with the "Cooling with air dehumidification" function
ProblemPossible causes/consequences and
Solutions
The indicator lamp in
thebutton
flashes three times or
remains off. The
"Cooling with air
dehumidification"
function cannot be
switched on.
Cooling with air dehumidification has been deactivated due to a
malfunction.
XVisit a qualified specialist workshop.
Setting climate control to automatic
Points to observe before use
The automatic function is only available in
conjunction with dual-zone automatic climate
control.
In automatic mode, the set temperature is
maintained automatically at a constant level.
The system automatically regulates the
temperature of the dispensed air, the airflow
and the air distribution.
The automatic mode functions optimally
when the "Cooling with air dehumidification"
function is activated. If necessary, cooling
with air dehumidification can be deactivated.
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
only deactivate the "Cooling with air-
dehumidification" function briefly.
Setting climate control to automatic
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XSet the desired temperature.
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up. Automatic air distribution and airflow
are activated.
XTo switch to manual mode:press the
orbutton.
or
XPress theorbutton.
The indicator lamp in thebutton goes
out. Automatic air distribution and airflow
are deactivated.
Setting the temperature
Automatic climate control
You can set the temperature for the entire
vehicle.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo increase/reduce:turn control
clockwise or counter-clockwise
(Ypage 121). Only change the temperature
setting in small increments. Start at 72 ‡
(22 †).
Dual-zone automatic climate control
Different temperatures can be set for the
driver's and front-passenger sides.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo increase/reduce:turn controlor
clockwise or counter-clockwise
(Ypage 123). Only change the temperature
Operating the climate control systems127
Climate control

setting in small increments. Start at 72 ‡
(22 †).
Setting the air distribution
Automatic climate control
Air distribution settings
Directs air through the defroster vents
Directs air through the center and side
air vents
Directs air through the footwell air
vents
iYou can also activate several air
distribution settings simultaneously. To do
this, press multiple air distribution buttons.
The air is then directed through various
vents.
Setting the air distribution
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XPress one or more of the,,
buttons.
The corresponding indicator lamp lights up
briefly.
Dual-zone automatic climate control
Air distribution settings
Directs air through the defroster vents
Directs air through the center and side
air vents
Directs air through the footwell air
vents
Directs air through the defroster,
center and side air vents
Directs air through the defroster and
footwell vents
iRegardless of the air distribution setting,
airflow is always directed through the side
air vents. The side air vents can only be
closed if the adjusters are turned clockwise
until they engage.
Setting the air distribution
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XPress theorbutton repeatedly
until the desired symbol appears in the
display.
Setting the airflow
Automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo increase/reduce:turn control
clockwise or counter-clockwise
(Ypage 121).
Dual-zone automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo increase/reduce:press theor
button.
Switching the ZONE function on/off
This function is only available with dual-zone
automatic climate control.
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up.
The temperature setting for the driver's
side is not adopted for the front-passenger
side.
XTo deactivate:press thebutton.
The indicator lamp in thebutton goes
out.
The temperature setting for the driver's
side is adopted for the front-passenger
side.
128Operating the climate control systems
Climate control

Defrosting the windshield
You can use this function to defrost the
windshield or to defrost theinside of the
windshield and the side windows.
iYou should only select the "Windshield
defrosting" functionuntil the windshield is
clear again.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo activate:press the button.
The indicator lamp in the button lights
up.
The climate control system switches to the
following functions:
Rhigh airflow
Rhigh temperature
Rairdistribution to the windshield and
front side windows
Rair-recirculation mode off
iThe "Windshield defrosting" function
automatically sets the blower output to the
optimum defrosting effect. As a result, the
airflow may increase or decrease
automatically after the button is pressed.
iYou can adjust the blower output
manually while the "Windshield defrosting"
function is in operation:
RAutomatic climate control: turn airflow
controlclockwise or counter-
clockwise (Ypage 121).
RDual-zone automatic climate control:
press theorbutton.
XTo deactivate:press the button.
The indicator lamp in the button goes
out. The previously selected settings are
restored. Air-recirculation mode remains
deactivated.
or
XDual-zone automatic climate control: press
thebutton.
The indicator lamp in the button goes
out. Airflow and air distribution are set to
automatic mode.
or
XAutomatic climate control: turn
temperature controlclockwise or
counter-clockwise (Ypage 121).
Dual-zone automatic climate control: turn
temperature controlorclockwise or
counter-clockwise (Ypage 123).
MAX COOL maximum cooling
The MAX COOL function is only available in
vehicles for the USA.
MAX COOL is only operational when the
engine is running.
XTo activate:press the
button.
The indicator lamp in the button lights up.
XTo deactivate:press the
button
again.
The indicator lamp goes out. The previously
selected settings are restored.
When you activate MAX COOL, climate
control switches to the following functions:
Rmaximum cooling
Rmaximum airflow
Rair-recirculation mode on
Defrosting the windows
Windows fogged up on theinside
Automatic climate control
XActivate the"Cooling with air
dehumidification" function.
XIf the windows continue to fog up, activate
the "Windshield defrosting" function.
iYou should only select this setting until
the windshield is clear again.
Operating the climate control systems129
Climate control

XTurn the SmartKey to position0in the
ignition lock or remove it (Ypage 137).
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up.
XTo deactivate:press thebutton.
The indicator lamp in thebutton goes
out.
iResidual heat is deactivated
automatically:
Rafter approximately 30 minutes
Rwhen the ignition is switched on
Rif the battery voltage drops
Setting the air vents
Important safety notes
GWARNING
Very hot or very cold air can flow from the air
vents. This could result in burns or frostbite in
the immediate vicinity of the air vents. There
is a risk of injury.
Make sure that all vehicle occupants always
maintain a sufficient distance to the air
outlets. If necessary, redirect the airflow to
another area of the vehicle interior.
In order to ensure the direct flow of fresh air
through the air vents into the vehicle interior,
please observe the following notes:
Rkeep the air inlet between the windshield
and the hood free of blockages, such as ice,
snow or leaves.
Rnever cover the air vents or air intake grilles
in the vehicle interior.
iYou can move the adjusters for the air
vents vertically or horizontally to set the
direction of the airflow.
iFor optimal climate control in the vehicle,
open the air vents completely and set the
adjusters to the central position.
Setting the center air vents
XTo open the center air vent:turn the
adjuster in one of center air vents
counter-clockwise.
XTo close the center air vent:turn the
adjuster in one of center air vents
clockwise until it engages.
Setting the side air vents
Side window defroster vent
Side air vent
XTo openaside air vent:turn the adjuster
in side air ventcounter-clockwise.
XTo closeaside air vent:turn the adjuster
in side air ventclockwise until it
engages.
132Setting the air vents
Climate control