2014 MERCEDES-BENZ CLA light

XRemove the cover in the front wheel
housing (Ypage 112).
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsertthe new bulb into bulb holder.
XInsert bulb holderinto the lamp and turn
it clockwise.
XAlign housing coverand turn it
clockwise until it engages.
XReplace the cover in the front wheel
housing (Ypage 112).
High-beam headlamps/daytime
running lamps/parking lamps/
standing lamps (vehicles with halogen
headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulbcounter-clockwise and pull it
out.
XInsert the new bulb and engage it to the
stop.
XAlign housing coverand turn it
clockwise until it engages.
Turn signals (halogen headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsert the new bulb into bulb holder.
XInsert bulb holderand turn it clockwise
until it engages.
Cornering light function (Intelligent
Light System)
XSwitch off the lights.
XOpen the hood.
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsert the new bulb into bulb holder.
Replacing bulbs113
Lights and windshield wipers
Z

XInsert bulb holderinto the lamp and turn
it clockwise.
XAlign housing coverand turn it
clockwise until it engages.
Changing the rear bulbs
Opening and closing the side trim
panels
You must open the side trim panel in the trunk
before you can change the bulbs in the tail
lamps.
Left-hand side trim panel
XTo open:turn release knob90° in the
direction of the arrow and remove side trim
panel.
XTo close:insert side trim paneland turn
release knob90° in the opposite
direction to the arrow.
Right-hand side trim panel
XTo open:loosenside trim panelat the
top and fold it down in the direction of the
arrow.
XTo close:insert side panel.
Tail lamp
XSwitch off the lights.
XOpen the trunk.
XOpen the side trim panel (Ypage 114).
XRelease and remove connector.
XPress retaining clipsat the same time in
the direction of the arrows.
XPull the bulb holder out with the bulbs.
Bulb holder
Brake lamp
Brake lamp
"Rear fog lamp
!Backup lamp
Turn signal
114Replacing bulbs
Lights and windshield wipers

XBrake lamp/rear fog lamp/backup
lamp:remove the corresponding bulb from
the bulb holder.
XInsert the new bulb into the bulb holder.
XTurn signal lamp:lightly press the bulb
into the bulb holder, turn it counter-
clockwise and remove it from bulb holder.
XInsert the new bulb into the bulb holderand
turn it clockwise.
XReinsert the bulb holderand engage on
retaining clips.
XRe-establish contact with the connector.
XClose the side trim panel (Ypage 114).
Windshieldwipers
Switching the windshield wipers on/
off
!Do not operate the windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
that has collected on the windshield can
scratch the glass if wiping takes place when
the windshield is dry.
If it is necessary to switch on the windshield
wipers in dry weather conditions, always
use washer fluid when operating the
windshield wipers.
!If the windshield wipers leave smears on
the windshield after the vehicle has been
washed in an automatic car wash, wax or
other residues may be the reason for this.
Clean the windshield using washer fluid
after washing the vehicle in an automatic
car wash.
Combination switch
Windshield wiper off

Intermittentwipe, low (rain sensor
set to low sensitivity)
Intermittentwipe, high (rain sensor
set to high sensitivity)
Continuous wipe, slow
Continuous wipe, fast
Single wipe/To wipe the
windshield using washer fluid
XSwitch on the ignition.
XTurn the combination switch to the
corresponding position.
!Vehicles with a rain sensor: if the
windshield becomes dirty in dry weather
conditions, the windshield wipers may be
activated inadvertently. This could then
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
Vehicles witharain sensor:in the
or
position, the appropriate wiping
frequency is automatically set according to
the intensity of the rain. In theposition,
the rainsensor is more sensitive than in
the
position, causing the windshield
wipers to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic
conditions.Replace the wiper blades twice a
year, ideally in spring and fall.
Windshield wipers115
Lights and windshield wipers
Z

Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could
be trapped by the wiper arm.There is a risk
of injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
!Never open the hood if a windshield wiper
arm has been folded away from the
windshield.
Never fold a windshield wiper arm without
a wiper blade back onto the windshield.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm without a wiper
blade and it falls onto the windshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Benzrecommends that you have
the wiper blades changed ataqualified
specialist workshop.
Changing the windshield wiper blades
Removing the wiper blades
XRemove the SmartKey from the ignition
lock.
XFold the wiper arm away from the
windshield.
XPress both release clips.
XFold wiper bladein the direction of
arrow"away from wiper arm!.
XRemove wiper bladein the direction of
arrow.
Installing the wiper blades
XPosition new wiper bladewith
recess on lug.
XFold wiper bladein the direction of
arrow"onto the wiper arm, until retaining
clipsengage in bracket!.
XMake sure that wiper bladeis seated
correctly.
XFold the wiper arm back onto the
windshield.
116Windshieldwipers
Lights and windshield wipers

Problems with the windshield wipers
ProblemPossible causes/consequences and
Solutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked at a qualified specialist
workshop.
The windshield washer
fluid from the spray
nozzles no longer hits
the center of the
windshield.
The spray nozzles are misaligned.
XHave the spray nozzles adjusted at a qualified specialist
workshop.
Windshield wipers117
Lights and windshield wipers
Z

Canada only
Sets the temperature, left (Ypage 127)
Sets climate control to automatic (Ypage 127)
"Defrosts the windshield (Ypage 129)
!Increases the airflow (Ypage 128)
Sets the air distribution (Ypage 128)
Display
Activates/deactivates air-recirculationmode (Ypage 131)
Switches climate control on/off (Ypage 125)
Sets the temperature, right (Ypage 127)
Switches the residual heat function on/off(Ypage 131)
Switches cooling with air dehumidification on/off (Ypage 125)
Reduces the airflow (Ypage 128)
Switches the rear window defroster on/off (Ypage 130)
Switches the ZONE function on/off (Ypage 128)
Notes on using dual-zone automatic
climate control
Automatic climate control
The following contains instructions and
recommendations to enable you to get the
most out of your automatic climate control.
RActivate climate controlusing theand
buttons. The indicator lamps in the
andbuttons light up.
RSet the temperature to 72 ‡ (22 †).
ROnly use the "Windshield defrosting"
function briefly until the windshield is clear
again.
ROnly use air-recirculation mode briefly, e.g.
if there are unpleasant outside odors or
when in a tunnel. The windows could
otherwise fog up, since no fresh air is drawn
into the vehicle in air-recirculation mode.
RUse the ZONE function to adopt the
temperature settings on the driver's side
for the front-passenger side as well.The
indicator lamp in thebutton goes out.
124Overview of climate control systems
Climate control

ROnly available on vehicles for Canada:
use the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
residual heat function can only be activated
or deactivated with the ignition switched
off.
RVehicles with COMAND:if you change the
settings of the climate control system, the
climate status display appears for three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the currentsettings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off, the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 140).
Operating the climate control
systems
Switching climate control on/off
Points to observe before use
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could fog up.
Therefore, switch off climate control only
briefly
Activating/deactivating
Automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo switch on:turn controlclockwise to
the desired position (except position0)
(Ypage 121).
XTo switch off:turn controlcounter-
clockwise to position0(Ypage 121).
Dual-zone automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up. Airflow and air distribution are set to
automatic mode.
or
XPress thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored.
XTo deactivate:press thebutton.
The indicator lamp in thebutton lights
up.
iDual-zone automatic climate control:
switch on climate control primarily using
thebutton.
Activating/deactivating cooling with
air dehumidification
Points to observe before use
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
only deactivate the "Cooling with air-
dehumidification" function briefly.
The cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and
Operating the climate control systems125
Climate control

dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when it is in cooling mode. This is
normal and not a sign that there is a
malfunction.
Activating/deactivating
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up.
XTo deactivate:press thebutton.
The indicator lamp in thebutton goes
out. The "Cooling with air dehumidification"
function has a delayed switch-offfeature.
126Operating the climate control systems
Climate control