2014 MERCEDES-BENZ CLA key

Rear fog lamp
The rearfog lamp improves visibility of your
vehicle for the traffic behind in the event of
thick fog. Please take note of the country-
specific regulations for the use of rear fog
lamps.
XTo switch on the rear fog lamps:turn the
SmartKey in the ignition lock to position2
or start the engine.
XTurn the light switch toor.
XPress thebutton.
The yellowindicator lamp in the
instrument cluster lights up.
XTo switch off the rear fog lamp:press the
button.
The yellowindicator lamp in the
instrument cluster goes out.
iWhen the rear fog lamp is switched on,
the center brake lamp in the tail lamp
switches off due to a legal requirement.
Parking lamps
!If the battery has been excessively
discharged, the parking lamps or standing
lamps are automatically switched off to
enable the next engine start.Always park
your vehicle safely and sufficiently lit
according to legal standards. Avoid the
continuous use of theparking lamps
for several hours. If possible, switch on the
right or theleft standing lamp.
XTo switch on:turn the light switch to
.
The greenindicator lamp in the
instrumentcluster lights up.
Standing lamps
Switching on the standinglamps ensures the
corresponding side of the vehicle is
illuminated.
XTo switch on the standing lamps:the
SmartKey is not in the ignition lock or it is
in position0.
XTurn the light switch to(left-hand side
of the vehicle) or(right-hand side of
the vehicle).
Combination switch
Turn signal
High-beam headlamps
Turn signal, right
"High-beam flasher
!Turn signal, left
XTo indicate briefly:press the combination
switch briefly to the pressure pointinthe
direction of arrowor!.
The corresponding turn signal flashes three
times.
XTo indicate:press the combination switch
beyond the pressure point in the direction
of arrowor!.
High-beam headlamps
XTo switch on the high-beam headlamps:
turn the SmartKey in the ignition lock to
position2or start the engine.
XTurn the light switch toor.
106Exterior lighting
Lights and windshield wipers

XPress the combination switch beyond the
pressure point in the direction of
arrow.
In theposition, the high-beam
headlamps are only switched on when it is
dark and the engine is running.
The blueindicator lamp in the
instrument cluster lights up when the high-
beam headlamps are switched on.
XTo switch off the high-beam
headlamps:move the combination switch
back to its normal position.
The blueindicator lamp in the
instrument cluster goes out.
iVehicles with Adaptive Highbeam Assist:
when Adaptive Highbeam Assist is active,
it controls activation of the high-beam
headlamps (Ypage 108).
High-beam flasher
XTo switch on:turn the SmartKey in the
ignition lock to position1or2or start the
engine.
XPull the combination switch in the direction
of arrow".
Hazard warning lamps
The hazard warning lamps automatically
switch on if:
Ran air bag is deployed
Rthe vehicle decelerates rapidly from a
speed of more than 45mph(70 km/h) and
comes to a standstill
XTo switch on the hazard warning lamps:
press button.
All turn signals flash. If you now switch on
a turn signal using the combination switch,
only the turn signal lamp on the
corresponding side of the vehicle will flash.
XTo switch off the hazard warning
lamps:press button.
The hazard warning lamps switch off
automatically if the vehicle reaches a speed
of over 6mph (10km/h) again after a full
brake application.
iThe hazard warning lamps still operate if
the ignition is switched off.
Headlamp cleaning system
The headlamps are cleaned automatically if
the "Wipe with washer fluid" function is
operated five times while the lights are on and
the engine is running (Ypage 115). When you
switch off the ignition, the automatic
headlamp cleaning system is reset and
counting is resumed from 0.
Cornering light function
The cornering light function improves the
illumination of the road over a wide angle in
the direction you are turning, enabling better
visibility in tight bends, for example. The
cornering light function can only be activated
whenthe low-beam headlamps are switched
on.
Exterior lighting107
Lights and windshield wipers
Z

Interior lighting
Overview of interior lighting
Front overhead control panel
To switch the left-hand frontreading
lamp on/off
To switch the front interior lighting
on
"To switch the on/off
!To switch the frontinterior lighting/
automatic interiorlighting control off
To switch the right-handfront
reading lamp on/off
To switch the automatic interior lighting
control on
Rear-compartment overhead control panel
To switch the left-hand reading lamp
on/off
To switch the right-hand reading
lamp on/off
Interior lighting control
Important notes
In order to prevent the vehicle's battery from
discharging, the interior lighting functions are
automatically deactivated after some time
unless the SmartKey is in position2in the
ignitionlock.
The brightness of the ambient lighting may be
set using the on-board computer
(Ypage 207).
Automatic interior lighting control
XTo switch on:set the switch to center
position .
XTo switch off:set the switch to the
position.
The interior lighting automatically switches
on if you:
Runlock the vehicle
Ropen a door
Rremove the SmartKey from the ignition
lock.
The interior light is activated for a short while
when the SmartKey is removed from the
ignition lock. You can activate this delayed
switch-off using the on-board computer
(Ypage 208).
Manual interior lighting control
XTo switch the front interior lighting on:
set the switch to theposition.
XTo switch the interior lighting off:set the
switch to theposition or (if the door
is closed) to the center position.
XTo switch the interior lighting on/off:
press the
button.
XTo switch the reading lamps on/off:
press thebutton.
110Interior lighting
Lights and windshiel dw ipers

Crash-responsive emergency lighting
The interiorlighting is activated automatically
if the vehicle is involved in an accident.
XTo switch off the crash-responsive
emergency lighting:press the hazard
warning lamp button.
or
XLockand then unlock the vehicle using the
key.
Replacing bulbs
Important safety notes
Xenon bulbs
GDANGER
Xenonbulbs carry a high voltage. You can get
an electric shock if you remove the cover of
the Xenon bulb and touch the electrical
contacts. There is a risk of fatal injury.
Never touch the parts or the electrical
contacts of the Xenon bulb. Always have work
on the Xenon bulbs carried out at a qualified
specialist workshop.
If your vehicle is equipped with Xenon bulbs,
you can recognize this by the following: the
cone of light from the Xenon bulbs moves
from the top to the bottom and back again
when you start the engine. For this to be
observed, the lights must be switched on
before starting the engine.
Bulbs and lamps are an important aspectof
vehicle safety.You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Other bulbs
GWARNING
Bulbs, lamps and connectors can get very hot
when operating. If you change a bulb, you
could burn yourself on these components.
There is a risk of injury.
Allow these components to cool down before
changing a bulb.
Do not use a bulb that has been dropped or if
its glass tube has been scratched.
The bulb may explode if:
Ryou touch it
Rit is hot
Ryou drop it
Ryou scratch it
Only operate bulbs in enclosed lamps
designed for that purpose. Only install spare
bulbs of the same type and the specified
voltage.
Marks on the glass tube reduce the service
life of the bulbs. Do not touch the glass tube
with your bare hands. If necessary, clean the
glass tube when cold with alcohol or spirit and
rub it off with a lint-free cloth.
Protectbulbs from moisture during
operation.Do not allow bulbs to come into
contact with liquids.
There are bulbs other than the Xenon bulbs
that you cannot replace. Replace only the
bulbs listed (Ypage 111). Have the bulbs that
you cannot replace yourself changed at a
qualified specialist workshop.
If you require assistance changing bulbs,
consult a qualified specialist workshop.
If the new bulb still does not light up, consult
a qualified specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Overview: changing bulbs/bulb types
You can change the following bulbs. The bulb
type can be found in the legend.
Replacing bulbs111
Lights and windshiel dw ipers
Z

Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could
be trapped by the wiper arm.There is a risk
of injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
!Never open the hood if a windshield wiper
arm has been folded away from the
windshield.
Never fold a windshield wiper arm without
a wiper blade back onto the windshield.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm without a wiper
blade and it falls onto the windshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Benzrecommends that you have
the wiper blades changed ataqualified
specialist workshop.
Changing the windshield wiper blades
Removing the wiper blades
XRemove the SmartKey from the ignition
lock.
XFold the wiper arm away from the
windshield.
XPress both release clips.
XFold wiper bladein the direction of
arrow"away from wiper arm!.
XRemove wiper bladein the direction of
arrow.
Installing the wiper blades
XPosition new wiper bladewith
recess on lug.
XFold wiper bladein the direction of
arrow"onto the wiper arm, until retaining
clipsengage in bracket!.
XMake sure that wiper bladeis seated
correctly.
XFold the wiper arm back onto the
windshield.
116Windshieldwipers
Lights and windshield wipers

Problems with the windshield wipers
ProblemPossible causes/consequences and
Solutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked at a qualified specialist
workshop.
The windshield washer
fluid from the spray
nozzles no longer hits
the center of the
windshield.
The spray nozzles are misaligned.
XHave the spray nozzles adjusted at a qualified specialist
workshop.
Windshield wipers117
Lights and windshield wipers
Z

Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
iRead the information on qualified
specialist workshops: (Ypage 25).
Overview of climate control systems
Important safety notes
Observe the settings recommended on the
following pages. The windows could
otherwise fog up.
To preventthe windows from fogging up:
Rswitch off climate control only briefly
Rswitch on air-recirculation mode only
briefly
Rswitch on the cooling with air
dehumidification function
Rswitch on the defrost windshield function
briefly, if required
The automatic climate control regulates the
temperature and the humidity of the vehicle
interior and filters out undesirable
substances from the air.
Automatic climate control/dual-zone
automatic climate control is only operational
when the engine is running. Optimum
operation is only achieved with the side
windows and panorama roof with power tilt/
sliding panel closed.
The residual heat function can only be
activated or deactivated with the ignition
switched off (Ypage 131).
iVentilate the vehicle for a brief period
during warm weather, e.g. using the
convenience opening feature (Ypage 84).
This will speed up the cooling process and
the desired vehicle interior temperature
will be reached more quickly.
iThe integrated filter filters out most
particles of dust and soot and completely
filters out pollen. With dual-zone automatic
climate control, gaseous pollutants and
odors will also be reduced.Aclogged filter
reduces the amountofair supplied to the
vehicle interior.For this reason, you should
always observe the interval for replacing
the filter, which is specified in the
Maintenance Booklet.As it depends on
environmental conditions, e.g. heavy air
pollution, the interval may be shorter than
stated in the Maintenance Booklet.
iIt is possible that the dehumidification
function of the climate control system may
be activated automatically an hour after the
SmartKey has been removed. The vehicle
is then ventilated for 30 minutes.
120Overview of climate control systems
Climate control

ROnly available on vehicles for Canada:
use the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
residual heat function can only be activated
or deactivated with the ignition switched
off.
RVehicles with COMAND:if you change the
settings of the climate control system, the
climate status display appears for three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the currentsettings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off, the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 140).
Operating the climate control
systems
Switching climate control on/off
Points to observe before use
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could fog up.
Therefore, switch off climate control only
briefly
Activating/deactivating
Automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo switch on:turn controlclockwise to
the desired position (except position0)
(Ypage 121).
XTo switch off:turn controlcounter-
clockwise to position0(Ypage 121).
Dual-zone automatic climate control
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up. Airflow and air distribution are set to
automatic mode.
or
XPress thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored.
XTo deactivate:press thebutton.
The indicator lamp in thebutton lights
up.
iDual-zone automatic climate control:
switch on climate control primarily using
thebutton.
Activating/deactivating cooling with
air dehumidification
Points to observe before use
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
only deactivate the "Cooling with air-
dehumidification" function briefly.
The cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and
Operating the climate control systems125
Climate control