Publication details
Internet
Further information about Mercedes-Benz
vehicles and about Daimler AG can be found
on the following websites:
http://www.mbusa.com (USA only)
http://www.mercedes-benz.ca (Canada
only)
Editorial office
You are welcome to forward any queries or
suggestions you may have regarding this
Operator's Manual to the technical
documentation team at the following
address:
Daimler AG, HPC: CAC, Customer Service,
70546 Stuttgart, Germany
©Daimler AG: Not to be reprinted, translated
or otherwise reproduced, in whole or in part,
without written permission from Daimler AG.
Symbols
Registered trademarks:
RBluetooth®is a registered trademark of
Bluetooth SIG Inc.
RDTS is a registered trademark of DTS, Inc.
RDolby and MLP are registered trademarks
of DOLBY Laboratories.
RBabySmart™, ESP®and PRE-SAFE®are
registered trademarks of Daimler AG.
RHomeLink®is a registered trademark of
Johnson Controls.
RiPod®and iTunes®are registered
trademarks of Apple Inc.
RLogic7®is a registered trademark of
Harman International Industries.
RMicrosoft®and Windows media®are
registered trademarks of Microsoft
Corporation.
RSIRIUS is a registered trademark of Sirius
XM Radio Inc.
RHD Radio is a registered trademark of
iBiquity Digital Corporation.
RGracenote®is a registered trademark of
Gracenote, Inc.
RZAGATSurvey®and related brands are
registered trademarks of ZagatSurvey,
LLC.
In this Operator's Manual you will find the
following symbols:
GWARNING
Warning notes draw your attention to hazards
that endanger your health or life, or the health
or life of others.
HEnvironmental note
Environmental notes provide you with
information on environmentally aware actions
or disposal.
!Notes on material damage alert you to
dangers that could lead to damage to your
vehicle.
iPractical tips or further information that
could be helpful to you.
XThis symbol indicates an
instruction that must be followed.
XSeveral of these symbols in
succession indicate an instruction
with several steps.
(Ypage)This symbol tells you where you
can find more information about a
topic.
YYThis symbol indicates a warning or
an instruction that is continued on
the next page.
DisplayDisplayThis font indicates a display in the
multifunction display/COMAND
display.
Parts of the software in the vehicle are
protected by copyright©2005
The FreeType Project
http://www.freetype.org. All rights
reserved.
As at 13.12.2012
XPress and hold one of buttons to !on
the integrated garage door opener.
After a short time, indicator lamp lights
up yellow.
iIndicator lamp lights up yellow as soon
as button , "or !is programmed for
the first time. If the selected button has
already been programmed, indicator
lamp will only light up yellow after ten
seconds have elapsed.
XRelease button , "or !. Indicator
lamp flashes yellow.
XPoint garage door remote control
towards buttons to !on the rear-view
mirror at a distance of 2 to 8 inches (5 to
20 cm).
iThe required distance between remote
control and the integrated garage door
opener depends on the garage door drive
system. Several attempts might be
necessary. You should test every position
for at least 25 seconds before trying
another position.
XPress and hold button on remotecontrol
until indicator lamp lights up green.
If indicator lamp lights up green or
flashes, then programming has been
successful.
XRelease button on remote control for
the garage door drive system.
XIf indicator lamp lights up red: repeat
the programming procedure for the
corresponding button on the rear-view
mirror. When doing so, vary the distance
between remote control and the rear-
view mirror.
iIf the indicator lamp flashes green after
successful programming, the garage door
system is using a rolling code. After
programming, you must synchronize the
garage door opener integrated in the rear-
view mirror with the receiver of the garage
door system.
Synchronizing the rolling code
Observe the "Important safety notes"
(Ypage 273).
Your vehicle must be within reach of the
garage door or exterior gate drive. Make sure
that neither your vehicle nor any persons/
objects are present within the sweep of the
door or gate.
XTurn the SmartKey to position2in the
ignition lock.
XPress the program button of the door or
gate drive (see the door or gate drive
operating instructions, e.g. under
"programming of additional remote
controls").
iUsually, you now have 30seconds to
initiate the next step.
XPress previously programmed button ,
"or !of the integrated garage door
opener until the door closes.
The rolling code synchronization is then
complete.
Notes on programming the remote
control
Canadianradio frequency laws require a
"break" (or interruption) of the transmission
signals after broadcasting for a few seconds.
Therefore, these signals may notlast long
enough for the integrated garage door
opener. The signal is notrecognized during
programming. Comparable with Canadian
law, some U.S.garage door openers also
feature a "break".
Proceed as follows:
Rif you live in Canada
Rif you have difficulties programming the
garage door opener (regardless of where
you live) when using the programming
steps
274Features
Stowage and features
