Page 337 of 354
Aspect ratio
Relationship between tire height and tire
width in percent.
Tire pressure
This is pressure inside the tire applying an
outward force to each square inch of the tire's
surface. The tire pressure is specified in
pounds per square inch (psi), in kilopascal
(kPa) or in bar. The tire pressure should only
be corrected when the tires are cold.
Tire pressure of cold tires
The tires are cold:
Rif the vehicle has been parked without
direct sunlightonthe tires for at least three
hours and
Rif the vehicle has not been driven further
than 1 mile (1.6 km)
Tread
The part of the tire that comes into contact
with the road.
Bead
The tire bead ensures that the tire sits
securely on the wheel. There are several steel
wires in the bead to prevent the tire from
coming loose from the wheel rim.
Sidewall
The part of the tire between the tread and the
bead.
Weight of optional extras
The combined weight of those optional extras
that weigh more than the replaced standard
part and more than 2.3 kg (5 lbs). These
optional extras, such as high-performance
brakes, level control, a roof rack or a high-
performance battery, are not included in the
curb weight and the weight of the
accessories.
TIN (Tire Identification Number)
This is a unique identifier which can be used
by a tire manufacturer to identify tires, for
example for a product recall, and thus identify
the purchasers. The TIN is made up of the
manufacturer's identity code, tire size, tire
type code and the manufacturing date.
Load bearing index
The load bearing index (also load index) is a
code that contains the maximum load bearing
capacity of a tire.
Traction
Traction is the result of friction between the
tires and the road surface.
Treadwear indicators
Narrow bars (tread wear bars) that are
distributed over the tire tread. If the tire tread
is level with the bars, the wear limit of in
(1.6 mm) has been reached.
Occupant distribution
The distribution of occupants in a vehicle at
their designated seating positions.
Total load limit
Nominal load and luggage load plus
68 kilograms (150 lb) multiplied by the
number of seats in the vehicle.
Definition of terms for tires and loading335
Wheels and tires
Z
Page 340 of 354
Observe the following when raising the
vehicle:
Rto raise the vehicle, only use the vehicle-
specific jack that has been tested and
approved by Mercedes-Benz.Ifused
incorrectly, the jack could tip over with the
vehicle raised.
Rthe jack is designed only to raise and hold
the vehicle for a short time while a wheel
is being changed. It is not suited for
performing maintenance work under the
vehicle.
Ravoid changing the wheel on uphill and
downhill slopes.
Rbefore raising the vehicle, secure it from
rolling away by applying the parking brake
and inserting wheel chocks. Never
disengage the parking brake while the
vehicle is raised.
Rthe jack must be placed on a firm, flat and
non-slip surface. On a loose surface, a
large, load-bearing underlay must be used.
On a slippery surface, a non-slip underlay
must be used, e.g. rubber mats.
Rdo not use wooden blocks or similar
objects as a jack underlay.Otherwise, the
jack will not be able to achieve its load-
bearing capacity due to the restricted
height.
Rmake sure thatthe distance between the
underside of the tires and the ground does
not exceed 1.2 in (3 cm).
Rnever place your hands and feet under the
raised vehicle.
Rnever lie under the raised vehicle.
Rnever start the engine when the vehicle is
raised.
Rnever open or close a door or the tailgate
when the vehicle is raised.
Rmake sure that no persons are present in
the vehicle when the vehicle is raised.
!The jack is designed exclusively for
jacking up the vehicle at the jacking points.
Otherwise, your vehicle could be damaged.
Steel wheel with wheel trim
XVehicles with steel wheels:carefully
reach into two of the wheel trim openings
and remove the wheel trim.
XUsing lug wrench , loosen the bolts on
the wheel you wish to change by about one
full turn. Do not unscrew the bolts
completely.
The jacking points are located just behind the
wheel housings of the front wheels and just
in front of the wheel housings of the rear
wheels (arrows).
338Changingawheel
Wheels and tires
Page 353 of 354
Refrigerant instruction label
Example: refrigerant instruction label
Warning symbol
Refrigerant filling capacity
"Applicable SAE standards
!PAG oil part number
Type of refrigerant
Warning symbols indicate:
Rpossible dangers
Rhaving service work carried out at a
qualified specialist workshop
Filling capacities
Missing values were not available at time of
going to print.
All modelsCapacity
Refrigerant
PAGoil
Vehicle data
General notes
Please note that for the specified vehicle
data:
Rthe heights specified may vary as a result
of:
-tires
-load
-condition of the suspension
-optional equipment
Dimensions and weights
Model Opening
height
CLA 25068.9 in
(1749 mm)
CLA 45 AMG 4MATIC68.0 in
(1727 mm)
Missing values were not available at time of
going to print.
CLA 250
Vehicle length182.3 in (4630 mm)
Vehicle width
including exterior
mirrors
80.0 in (2032 mm)
Vehicle height56.5 in (1436 mm)
Wheelbase106.3 in (2699 mm)
Turning radius36.1 ft (11 m)
Maximum roof
load
Missing values were not available at time of
going to print.
CLA 45 AMG 4MATIC
Vehicle length184.7 in (4691 mm)
Vehicle width
including exterior
mirrors
80.0 in (2031 mm)
Vehicle data351
Technical data
Z