2014 LEXUS LX570 reset

14
LX570_OM_OM60L21U_(U)Pictorial index Instrument panelHeadlight switch
Turn signal lever
Fog light switch P. 206
P. 187
P. 218
Windshield wipers and washer switch
Rear window wiper and washer switch P. 220
P. 226
Hood opener P. 746Gauges and meters
Multi-information display P. 190
P. 198
Glove box P. 687
SRS knee airbags P. 124
Fuel filler door opener P. 114
Bottle holder P. 692Tire pressure warning reset switch P. 764

8311-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
LX570_OM_OM60L21U_(U) Driving position memory system Your preferred driving position (the po sition of the driver’s seat, steering
wheel and outside rear view mirrors) can be entered into the computer’s
memory and recalled with the touch of a button. It is also possible to set this
function to activate automatica lly when the doors are unlocked.
Three different driving positions can be entered into memory.
■ Entering a position to memory
Turn the “ENGINE START STOP ” switch to IGNITION ON
mode.
Adjust the driver’s seat, steeri ng wheel, and outside rear view
mirrors to the desired positions.
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press and hold button “1”, “2” or
“3” until the signal beeps. If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
■ Recalling the memorized position
Check that the shift lever is set in “P”.
Turn the “ENGINE START STOP ” switch to IGNITION ON
mode.
Press button “1”, “2” or “3” to
recall the desired position.STEP 1
STEP 2
STEP 3
STEP 1
STEP 2

861-3. Adjustable components (s eats, mirrors, steering wheel)
LX570_OM_OM60L21U_(U) ■
Retained accessory power ●
Each memorized position (except for the steering wheel position) can be acti-
vated within 3 minutes after the driver’s door is opened, even if the “ENGINE
START STOP” switch is turned off. ●
Each memorized position (except for the steering wheel position) can be acti-
vated within 60 seconds after the driver’s door is closed, even if the “ENGINE
START STOP” switch is turned off.■
To cancel seat position recall
Perform any one of the following operations. ●
Press the “SET” button ●
Press button “1”, “2” or “3”. ●
Adjust the seat using the switches (only cancels seat position recall) ●
Adjust the steering wheel using the tilt and telescopic steering control switch
(only cancels steering wheel position recall) ■
If the battery is disconnected
The memorized positions must be reset because the computer’s memory is erased
when the battery is disconnected.
CAUTION■
Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear passenger or
squeeze your body against the steering wheel.

1912-2. Instrument cluster
2
When driving
LX570_OM_OM60L21U_(U) Switching the display
Pressing this button switches between odometer and trip meter.
Odometer
Trip meter A
*Trip meter B
*
* : Pushing and holding the button will
reset the trip meter.Odometer and trip meter Odometer: Displays the total distance the vehicle has been driven
Trip meter: Displays the distance the vehicle has been driven since the
meter was last reset. Trip meters A and B can be used to record and dis-
play different distances independently
Odometer/trip meter disp lay change buttonSwitches between odometer and trip meter displays
Instrument panel light control dial The brightness of the instrume nt panel light can be adjusted

2002-2. Instrument cluster
LX570_OM_OM60L21U_(U) Switching the display
Display items can be switched by
pressing the “DISP” switch.
Display items
■ Outside temperature display
■ Average fuel consumption and Eco Driving Indicator Zone Display
(  P. 166) Displays the outside temperature • The temperature range that can be displayed
is from -40  F (-40  C) to 122  F (50  C).
• When Crawl control and Multi-terrain Select
is operating, the temperature is displayed on
the top of the multi-information display. Oth-
erwise, it is displayed in the middle of the
multi-information display.
Displays the average fuel consumption since
the function was reset • The function can be reset by pressing the
“DISP” switch for longer than 1 second when
the average fuel consumption is displayed.
• Use the displayed average fuel consumption
as a reference.

2022-2. Instrument cluster
LX570_OM_OM60L21U_(U) ■ Average vehicle speed
■ Front tire angle
■ Turn-by-turn navigation setting screen Displays the average vehicle speed since the
engine was started or the function was reset The function can be reset by pressing the “DISP”
switch for longer than 1 second when the aver-
age vehicle speed is displayed.
Displays the direction of the front tires The tire direction is displayed in 3 stages for
both left and right, in accordance with the angle
of the tire.
The turn-by-turn navigati on can be set to on or
off. The function can be activated or deactivated by
pressing the “DISP” switch for longer than 1 sec-
ond when turn-by-turn navigation setting
screen is displayed.

2052-2. Instrument cluster
2
When driving
LX570_OM_OM60L21U_(U) ■
Outside temperature display
In the following situations, the correct outside temperature may not be displayed, or
the display may take longer than normal to change: ●
When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●
When the outside temperature has changed suddenly (at the entrance/exit of a
garage, tunnel, etc.)■
When “--” or “E” is displayed
The system may be malfunctioning. Take your vehicle Lexus dealer.■
When disconnecting and reconnecting battery terminals
The following information data will be reset: ●
Average fuel consumption after refueling ●
Average fuel consumption ●
Average vehicle speed
CAUTION■
The information display at low temperatures
Allow the interior of the vehicle to warm up before using the information display. At
extremely low temperatures, the information display monitor may respond slowly,
and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear number
appearing on the display. This lag could cause the driver to downshift again, causing
rapid and excessive engine braking and po ssibly an accident resulting in death or
serious injury.

2322-4. Using other driving systems
LX570_OM_OM60L21U_(U) ■
Cruise control can be set when ●
The shift lever is in “D” or range “4” or higher of “S” has been selected. ●
Range “4” or higher has been selected by using the paddle shift. (vehicles with
paddle shift switches) ●
Vehicle speed is above appr oximately 25 mph (40 km/h).■
Accelerating after setting the vehicle speed ●
The vehicle can be accelerated normally. After acceleration, the set speed
resumes. ●
Even without canceling the cruise cont rol, the set speed can be increased by
first accelerating the vehicle to the desired speed and then pushing the lever
down to set the new speed. ■
Automatic cruise control cancelation
Cruise control will stop maintaining the ve hicle speed in any of the following situa-
tions. ●
Actual vehicle speed falls more than approximately 10 mph (16 km/h) below the
preset vehicle speed.
At this time, the memorized set speed is not retained. ●
VSC is activated. ●
Actual vehicle speed is below approximately 25 mph (40 km/h). ●
The switching operation continues for 5 seconds or more after the center dif-
ferential lock switch has been operated.■
If the warning message for the cruise control is shown on the multi-information
display
Press the “ON-OFF” button once to deactivate the system, and then press the but-
ton again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels immediately
after being activated, there may be a malfun ction in the cruise control system. Have
the vehicle inspected by your Lexus dealer.