2014 Lexus IS250 navigation

277
1. SPEECH COMMAND SYSTEM OPERATION
SPEECH COMMAND SYSTEM
IS300h/250_Navi_EE
5
1Press the talk switch.
2Say “Go home” or select “Go home”.
zA confirmation screen will be displayed
showing the recognition results.
3Say “Yes” or select “Yes”.
zThe system starts searching for a route to
your home.
zWhen the speech command is recognized,
the map of the area around the home
address will be displayed and route guid-
ance to the home address will begin.
INFORMATION
●
If the system does not respond or the
confirmation screen does not disappear,
press the talk switch and try again.
●If a speech command cannot be recog-
nized, voice guidance will say “Pardon?”
and speech command reception will
restart.
●If a speech command cannot be recog-
nized 2 consecutive times, the speech
command guidance system will say “To
restart voice recognition, push the talk
switch.”. Then voice recognition will be
suspended.
●The voice recognition prompt can be set
to on or off when “Voice prompts” is
selected. This setting can also be
changed on the “Voice settings” screen.
(→P. 8 4 )
●Voice guidance can be canceled by set-
ting voice prompts to off. Use this setting
when it is desirable to say a command
immediately after pressing the talk switch
and hearing a beep.
SPEECH COMMAND
EXAMPLE: SEARCHING FOR
A ROUTE TO YOUR HOME*
zIf a home address is not registered, voice
guidance will say “Your home is not set.”.
Please try again after setting a home
location. (→P.151)
*: With navigation function
IS_Navi_EE_53C71E.book 277 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

278
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
1Press the talk switch.
2Say “Enter an address” or select “Enter
an address”.
zThe searchable countries are restricted
according to the voice recognition lan-
guage.
zSome areas cannot be recognized by the
voice recognition system.
XFor UK English and French
3Say “”, “”
and “” continuously.
XExcept for UK English and French
3Say “”, “”
and “” continuously.
zSay the desired house number in the place
of the “<>”. It is possible to only say the num-
bers. For example, 1,2,3,4 etc. (It is not pos-
sible to say cardinals.) Inputting the house
number can be skipped.
zSay the desired full street name that
belongs to the set country in the place of
the “<>”. If only the city name was said at
step 3, say the street name. If the street
name is not unique, select the appropriate
number from the displayed address list.
zSay the desired city name or city name and
street name that belongs to the set country
in the place of the “<>”. Not just the city
name, but the city name and street name
can be said at the same time. If both are
said at the same time and the street name is
not unique, select the appropriate number
from the displayed address list.
SPEECH COMMAND
EXAMPLE: PERFORMING A
DESTINATION SEARCH BY
ADDRESS*
Use the official language of the country
the desired destination is in. A destina-
tion search by address, using speech
command, can only be performed for
countries that have one of the following
15 languages as their official language.
· Dutch
· French
· German
· Italian
· Spanish
· UK English
· Russian
· Portuguese
· Swedish
· Danish
· Finnish
· Greek
· Polish
· Turkish
· Czech
For changing voice recognition lan-
guages: →P.75
*: With navigation function
IS_Navi_EE_53C71E.book 278 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

282
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
2. COMMAND LIST
zFrequently used commands are listed in the following tables.
zFor devices that are not installed in the vehicle, the related commands will not be dis-
played in the “Shortcuts” screen. Also, according to conditions, other commands may
not be displayed in the “Shortcuts” screen.
zThe functions available may vary according to the system installed.
zCommands that have “O” in the shortcuts menu column can be recognized from the
“Shortcuts” screen.
XBasic
XNavi*
1
*1: With navigation function
*2: For example; “Restaurant”, “Hospital” etc.
Recognizable speech commands and their actions are shown below.
zVoice recognition language can be changed. (→P. 7 5 )
CommandAction
“Help”Prompts voice guidance to offer examples of commands
and operation methods
“Go back”Returns to the previous screen
CommandActionShortcuts
menu
“Find nearby ”Displays a list of near the cur-
rent positionO
“Enter an address”Enables setting a destination by saying the ad-
dressO
“Go home”Displays the route to homeO
IS_Navi_EE_53C71E.book 282 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

329
1. TELEPHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
IS300h/250_Navi_EE
TELEPHONE
7
3. CALLING ON THE Bluetooth® PHONE
1Press the “MENU” button on the
Remote Touch.
2Select “Telephone”.
3Select the desired button to call from.
zThe telephone top screen can be displayed
by pressing the switch on the steering
wheel.
*: With navigation function
After a Bluetooth® phone has been reg-
istered, a call can be made using the
hands-free system. There are several
methods by which a call can be made, as
described below.
How to make a call listPage
By favourites list330
By call history330
By contacts list332
By dial pad33 4
By e-mail/SMS/MMS345
By POI call*107
SOS335
By off hook switch335
By speech command system280
IS_Navi_EE_53C71E.book 329 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

345
1. TELEPHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
TELEPHONE
IS300h/250_Navi_EE
7
■EDITING QUICK REPLY MESSAG-
ES
1Select “Quick message”.
2Select corresponding to the de-
sired message to edit.
3Select “OK” when editing is completed.
*: With navigation function
■CALLING FROM E-MAIL/SMS/
MMS MESSAGE DISPLAY
1Display the “Messages” screen.
(→P.341)
2Select the desired message.
3Select .
zIf there are 2 or more telephone numbers,
select the desired number.
4Check that the “Call” screen is dis-
played.
INFORMATION
●To reset the edited quick reply messages,
select “Defaults”.
●“Quick message 1” (“I am driving and
will arrive in approximately [ETA]
minutes.”)*:
This message cannot be edited and will
automatically fill in [ETA] with the
navigation calculated estimated time of
arrival on the confirm message screen.
If there are waypoints set, [ETA] to the
next waypoint will be shown.
If there is no route currently set in the
navigation system, “Quick message 1”
cannot be selected.
CALLING THE MESSAGE
SENDER
Calls can be made to an e-mail/SMS/
MMS message sender’s telephone
number.
IS_Navi_EE_53C71E.book 345 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

8
371
IS300h/250_Navi_EE
8
2
1
3
4
5
6
7
1. CONNECTED SERVICES
OVERVIEW ........................................... 372
BEFORE USING CONNECTED
SERVICES............................................................... 374
2. SETTINGS REQUIRED FOR
USING THE SERVICE ....................... 375
OBTAINING LEXUS PORTAL SITE
ACCOUNT ........................................................... 375
CONNECTING TO INTERNET .................... 376
3. ONLINE SEARCH .................................. 377
ONLINE SEARCH................................................. 377
VIEWING POI*2 DETAILS................................. 381
4.IMPORTING MEMORY POINTS AND
STORED ROUTES ....................................... 382
REGISTERING AN EXTERNAL
POINT AS A MEMORY POINT AND
ROUTES FROM THE INTERNET ............. 382
PROCEDURE FOR DOWNLOADING
MEMORY POINTS AND ROUTES
FROM A USB MEMORY .............................. 383
5. Street View................................................. 385
6. Panoramio .................................................. 3871. CONNECTED SERVICE
SETTINGS............................................... 389
CONNECTED SERVICE SETTINGS
SCREEN ................................................................. 390
1CONNECTED SERVICES2SETUP
CONNECTED SERVICES*1
Not all connected services may be available in all countries.
*1: With navigation function
*2: Point of Interest
IS_Navi_EE_53C71E.book 371 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

374
1. CONNECTED SERVICES
IS300h/250_Navi_EE
BEFORE USING CONNECTED
SERVICES
Observe the following precaution:
• Before using this service, it is neces-
sary to access Lexus portal site via a
personal computer and create an
account. When creating an account,
“Navigation identification” will be
required. Navigation identification:
→P. 3 7 5
When using a cellular phone to connect
to the internet, observe the following
precautions:
•In order to use this service, a
Bluetooth
® DUN/PAN compatible
cellular phone with sufficient network
coverage and a SIM card with a con-
tract that allows access to the internet
are required.
• When using the connected services,
depending on your telephone sub-
scription, some related fees might
apply.
• When a cellular phone is used in a
roaming situation (when outside the
geographical coverage area of
mobile network provider) connection
fees may apply.
IS_Navi_EE_53C71E.book 374 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

375
1. CONNECTED SERVICES
IS300h/250_Navi_EE
CONNECTED SERVICES
8
2. SETTINGS REQUIRED FOR USING THE SERVICE
1Press the “MENU” button on the
Remote Touch.
2Select “Setup”.
3Select “Navigation”.
4Select “Connected service”.
5Check that navigation identification is
displayed.
OBTAINING LEXUS PORTAL
SITE ACCOUNT
Before using connected services, it is
necessary to first access Lexus portal
site (www.my.lexus.eu
) via a personal
computer etc. and create an account.
CHECKING NAVIGATION
IDENTIFICATION
IS_Navi_EE_53C71E.book 375 ページ ２０１４年５月２９日　木曜日　午前１１時２２分