2014 Lexus CT200h ECU

4336-3. Using the storage features
CT200h_OM_OM76135E_(EE)
6
Interior features
Luggage compartment features
Raise the hook to use.
The cargo hooks are provided for
securing loose items.
Secure the first-aid kit. To loosen
To t i g h t e n
Cargo hooks
First-aid kit storage belt
1
2
Auxiliary boxes
XCenter XRight side
Lift the center deck board. Lift the right side deck board.
CT200h_OM_OM76135E_(EE).book Page 433 Friday, May 30, 2014 1 1:14 AM

4346-3. Using the storage features
CT200h_OM_OM76135E_(EE)
■Using the luggage cover
Pull out the luggage cover and
secure it to the hook brackets.
■Removing the luggage cover
Retract the cover and release both
ends, then lift it out.
XLeft side (if equipped)
Lift the left side deck board.
Luggage cover (if equipped)
CT200h_OM_OM76135E_(EE).book Page 434 Friday, May 30, 2014 1 1:14 AM

4537-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
WA R N I N G
■Pre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may op en while the vehicle is in motion and cause
an accident, which may result in death or serious injury.
■After installing the support rod into the slot
Make sure the rod supports the hood securely from falling down on to your head or
body.
NOTICE
■When closing the hood
Be sure to return the support rod to its clip before closing the hood. Closing the hood
without returning the support rod properly could cause the hood to bend.
CT200h_OM_OM76135E_(EE).book Page 453 Friday, May 30, 2014 1 1:14 AM

4567-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
■Removing the engine compartment cover
■Installing the clipsPush up center portion
Insert
Press
With the engine at operating temperature and turned off, check the oil level on
the dipstick.
■Checking the engine oil Park the vehicle on level ground. After warming up the engine and turning
off the hybrid system, wait more than 5 minutes for the oil to drain back into
the bottom of the engine.
Engine compartment cover
1
2
3
NOTICE
■After installing an engine compartment cover
Make sure that the cover is securely installed in its original position.
Engine oil
1
CT200h_OM_OM76135E_(EE).book Page 456 Friday, May 30, 2014 1 1:14 AM

4957-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb with
the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check
that it is not loose, turn the headlight
high beams on once and visually
confirm that no light is leaking
through the mounting.
When installing the cover, conduct step in reverse.
■Halogen front fog light (if equipped) Remove 2 screws, a bolt and clip,
and pull down the fender liner.
Pull the fender liner down slowly,
being careful not to dislodge any
fixed components.
4
5
61
1
CT200h_OM_OM76135E_(EE).book Page 495 Friday, May 30, 2014 1 1:14 AM

5027-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
After installing the new bulb,
secure the socket to the light
body.
When inserting the socket, align the
marks printed on the light body and
the socket.
Install the visor cover on the mir-
ror frame, secure it with a screw,
and install the side turn signal light
and outer foot light.
Use only the screw position shown in
the illustration.
Side turn signal light: Align the tabs
on the light and th e cover and install.
Outer foot light: Interlock the tabs in
the groove of the light body with
those on the cover, and secure.
Disconnect the tabs, and sepa-
rate the top and bottom of the
rear side cover of the mirror.
7
8
9
CT200h_OM_OM76135E_(EE).book Page 502 Friday, May 30, 2014 1 1:14 AM

5037-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
Install the cover of the back end
of the mirror, installing the lower
side and the upper side in that
order.
When installin g the lower side of the
cover, insert the side turn signal light
pin into the hole in the cover.
Secure the cover with screws and
reconnect the connectors back
together.
Secure the cords by returning them
to the hooks as they were.
Align the tabs, and secure the
mirror by pushing in each diago-
nally-opposite pair of tabs in
order.
Make sure to insert the tabs in order
as shown in the illustration, and push
them in until a click is heard.
If you do not hear the click, do not
force the tabs in. Instead, remove the
mirror and check that the tabs are
aligned.
10
11
12
CT200h_OM_OM76135E_(EE).book Page 503 Friday, May 30, 2014 1 1:14 AM

5057-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
WA R N I N G
■Replacing light bulbs
●Be sure to stop the hybrid system and turn off the lights. Do not attempt to replace the
bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bu lb with bare hands. When it is unavoid-
able to hold the glass portion, use and hold with a clean dry cloth to avoid getting
moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or water entering th e headlight unit. This may damage the head-
lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or
component parts.
Doing so may result in death or serious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installing to prevent heat damage.
NOTICE
■When replacing the outer foot lights
If the front window is stopping you from conducting the replace operation properly,
open the window on the side you are workin g on to allow you enough space to work.
Continuing the operation without giving yourself enough space to work could lead you
to scratch the vehicle.
CT200h_OM_OM76135E_(EE).book Page 505 Friday, May 30, 2014 1 1:14 AM