2014 Lexus CT200h change

5288-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
An attempt was made to change the shift position when
the 12-volt battery voltage was low.A buzzer also sounds.
→ Recharge or replace the 12-volt battery.
Indicates that the shift lever and P position switch were
repeatedly operated in quick succession.
A buzzer also sounds.
→ Wait approximately 20 seconds and change the
shift position.
An attempt was made to shift the shift position from P or
N to B.
A buzzer also sounds.
→ Shift the shift position to D, and then shift the shift
position to B.
Wa r n i n g m e s s a g eDetails/Actions
CT200h_OM_OM76135E_(EE).book Page 528 Friday, May 30, 2014 1 1:14 AM

5298-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
8
When trouble arises
An attempt was made to shift the shift position to R, D or
B with the power switch on (READY indicator turned
off). A buzzer also sounds.
→ After starting the hybrid system, shift the shift posi-
tion to R, D or B
*.
*: When shifting the shift position to B, first shift the
shift position to D, and then shift the shift position to
B.
An attempt was made to shift the shift position from P
with the brake pedal released. A buzzer also sounds.
→ When shifting the shift position from P, depress the
brake pedal.
An attempt was made to shift the shift position from R to
B.
A buzzer also sounds.
The shift position automatically changed to N.
→ Shift the shift position to D, and then shift the shift
position to B.
Wa r n i n g m e s s a g eDetails/Actions
(Flashes)
(Flashes)
(Flashes)
CT200h_OM_OM76135E_(EE).book Page 529 Friday, May 30, 2014 1 1:14 AM

5308-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
An attempt was made to shift the shift position to D while
the vehicle was moving in reverse.A buzzer also sounds.
The shift position automatically changed to N.
→ Stop the vehicle, and then change the shift position.
An attempt was made to shift the shift position to R while
the vehicle was moving forward.
A buzzer also sounds.
The shift position automatically changed to N.
→ Stop the vehicle, and then change the shift position.
Indicates that the P position switch is pressed while the
vehicle is running. A buzzer also sounds.
The shift position automatically changed to N.
→ To shift the shift position to P, stop the vehicle com-
pletely and press the P position switch.
→ To continue driving, shift the shift position to D or R.
Wa r n i n g m e s s a g eDetails/Actions
(Flashes)
(Flashes)
(Flashes)
CT200h_OM_OM76135E_(EE).book Page 530 Friday, May 30, 2014 1 1:14 AM

5668-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
■Stopping the hybrid system
Set the parking brake, shift the shift position to P and press the power switch as you nor-
mally do when stopping the hybrid system.
■Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the electronic
key battery be replaced immediately when the battery is depleted. (→P. 4 8 3 )
■Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set, the alarm
may be triggered. ( →P. 8 5 )
■Changing power switch modes
Within 10 seconds of the buzzer sounding, release the brake pedal and press the power
switch.
The hybrid system does not start and modes will be changed each time the switch is
pressed. ( →P. 1 7 8 )
WA R N I N G
■When using the mechanical key and operating the power windows
Operate the power window after checking to make sure that there is no possibility of
any passenger having any of their body parts caught in the window.
Also, do not allow children to operate the mechanical key. It is possible for children and
other passengers to get caught in power window.
CT200h_OM_OM76135E_(EE).book Page 566 Friday, May 30, 2014 1 1:14 AM

5698-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
8
When trouble arises
Close the exclusive jump starting terminal cover, and reinstall the fuse box
cover to its original position.
Once the hybrid system starts, have the vehicle inspected at any authorized
Lexus dealer or repairer, or another duly qualified and equipped professional as
soon as possible.
■Starting the hybrid system when the 12-volt battery is discharged
The hybrid system cannot be started by push-starting.
■To prevent 12-volt battery discharge
●Turn off the headlights and the audio system while the hybrid system is off.
●Turn off any unnecessary electrical components when the vehicle is running at a low
speed for an extended period, such as in heavy traffic.
■When the 12-volt battery is removed or discharged
●The hybrid system may not start. ( →P. 4 6 5 )
●If the 12-volt battery discharges while the shift position is in P, it may not be possible to
shift the shift position to other positions. In this case, the vehicle cannot be towed with-
out lifting both front wheels because the front wheels will be locked. ( →P. 5 1 0 )
●When the 12-volt battery is reconnected, start the hybrid system and confirm that the
shift position can be changed to each position using the shift position indicator.
●Make sure that the key is not inside the vehicle when recharging or replacing the 12-
volt battery. The key may be locked in the vehicle if the alarm is activated. (→P. 8 5 )
■Charging the 12-volt battery
The electricity stored in the 12-volt battery will discharge gradually even when the vehicle
is not in use, due to natural discharge and the draining effects of certain electrical appli-
ances. If the vehicle is left for a long time, the 12-volt battery may discharge, and the
hybrid system may be unable to start. (The 12-volt battery recharges automatically while
the hybrid system is operating.)
WA R N I N G
■Avoiding 12-volt battery fires or explosions
Observe the following precautions to prevent accidentally igniting the flammable gas
that may be emitted from the 12-volt battery:
●Make sure each jumper cable is connected to the correct terminal and that it is not
unintentionally in contact with any other than the intended terminal.
●Do not allow the other end of the jumper cable connected to the “+” terminal to come
into contact with any other parts or metal surfaces in the area, such as brackets or
unpainted metal.
●Do not allow the + and - clamps of the jumper cables to come into contact with each
other.
●Do not smoke, use matches, cigarette lighters or allow open flame near the 12-volt
battery.
9
CT200h_OM_OM76135E_(EE).book Page 569 Friday, May 30, 2014 1 1:14 AM

5758-2. Steps to take in an emergency
CT200h_OM_OM76135E_(EE)
8
When trouble arises
If the vehicle becomes stuck
Set the parking brake and shift the shift po sition to P. Stop the hybrid system.
Remove the mud, snow or sand from around the stuck tire.
Place wood, stones or some other material under the tires to help provide
traction.
Restart the hybrid system.
Shift the shift position to D or R, rele ase the parking brake and carefully apply
the accelerator to free the vehicle.
■When it is difficult to free the vehicle
Carry out the following procedures if the tires spin or the vehicle becomes
stuck in mud, dirt or snow:
Press to turn off TRC. ( →P. 2 3 9 )
WA R N I N G
■When attempting to free a stuck vehicle
If you choose to push the vehicle back and forth to free it, make sure the surrounding
area is clear to avoid striking other vehi cles, objects or people. The vehicle may also
lunge forward or lunge back suddenly as it becomes free. Use extreme caution.
■When changing the shift position
Be careful not to change the shift position with the accelerator pedal depressed.
Changing the shift position to any positions other than P or N may cause the vehicle to
accelerate abruptly, causing an accident and resulting in death or serious injury.
1
2
3
4
5
CT200h_OM_OM76135E_(EE).book Page 575 Friday, May 30, 2014 1 1:14 AM

581
9
9-1. Specifications
Vehicle specifications
CT200h_OM_OM76135E_(EE)
■Engine oil selection
“Toyota Genuine Motor Oil” is used in your Lexus vehicle. Lexus recom-
mends the use of approved “Toyota Ge
nuine Motor Oil”. Another motor oil of
matching quality can also be used.
Oil grade:
0W-20, 5W-20, 5W-30 and 10W-30:
API grade SL “Energy-Conserving”, SM “Energy-Conserving” or SN
“Resource-Conserving”; or ILSAC multigrade engine oil
1 5 W- 4 0 a n d 2 0 W- 5 0 :
API grade SL, SM or SN multigrade engine oil
Recommended viscosity (SAE):
SAE 0W-20 is filled into your Lexus
vehicle at manufacturing, and the
best choice for good fuel economy
and good starting in cold weather.
If SAE 0W-20 oil is not available,
SAE 5W-30 oil may be used. How-
ever, it should be replaced with SAE
0W-20 at the next oil change.
If you use SAE 10W-30 or a higher
viscosity engine oil in extremely low
temperatures, the engine may
become difficult to start, so SAE
0 W-20, 5W-20 or 5W-30 engine
oil is recommended.
Oil viscosity (0W-20 is explained here as an example): • The 0W in 0W-20 indicates the characteristic of the oil which allows cold
startability. Oils with a lower value before the W allow for easier starting of
the engine in cold weather.
• The 20 in 0W-20 indicates the viscosit y characteristic of the oil when the
oil is at high temperature. An oil with a higher viscosity (one with a higher
value) may be better suited if the vehicle is operated at high speeds, or
under extreme load conditions.
Temperature range anticipated
before next oil change Preferred
CT200h_OM_OM76135E_(EE).book Page 581 Friday, May 30, 2014 1
1:14 AM

5899-2. Customization
CT200h_OM_OM76135E_(EE)
9
Vehicle specifications
Customizable features
Some function settings are changed simu ltaneously with other functions being
customized. Contact any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional for further details.
When customizing vehicle features, ensure that the vehicle is parked in a safe
place with the shift position in P and the parking brake set.
■Changing using the Remote Touch
Press the “MENU” button on the Remote Touch.
Select “Setup” on the “Menu” screen and select “Vehicle”.
Various setting can be changed. Refer to the list of settings that can be
changed for details.
■Changing using the Lexus Display Audio controller Press the “MENU” button on the Lexus Display Audio controller.
Select “Setup” on the “MENU” screen and select “Vehicle”.
Various setting can be changed. Refer to the list of settings that can be
changed for details.
Your vehicle includes a variety of electr onic features that can be personalized
to suit your preferences. The settings of these features can be changed using
the multi-information display, the Remote Touch or Lexus Display Audio con-
troller, or at any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional.
Customizing vehicle features
1
2
1
2
CT200h_OM_OM76135E_(EE).book Page 589 Friday, May 30, 2014 1 1:14 AM