2014 Lancia Delta weight

206
IN AN EMERGENCY
❍rest the subwoofer to one side in the luggage com-
partment, remove the container and take out the space-
saver wheel;
❍change the wheel as described in this chapter.
At the end of the operation:
❍reposition the container and place the subwoofer on
top of it, taking care to position it according to the in-
structions on the container (fig. 9) so that the arrow
on the spacer is pointing in the direction of travel.
❍rest cable B - fig. 8 on velcro attachment C to avoid
pinching it. Then tighten locking device A - fig. 8. Low-
er the luggage compartment mat.
fig. 9
L0E0177m
TAKING OUT THE SPACE-SAVER WHEEL
Please note that:
❍the jack weight is 1.76 kg;
❍the jack requires no adjustment;
❍the jack cannot be repaired; if it breaks, it must be
replaced with a new one of the same type;
❍no tool other than its cranking device may be fitted on
the jack.
To change a wheel, proceed as follows:
❍stop the car where it is not a danger to other road users
and you can replace the wheel safely. The ground
should be flat if possible, and sufficiently firm;
❍turn the engine off and engage the handbrake;
❍engage first gear or reverse;
❍lift up the luggage compartment mat using handle
A - fig. 10 (in the presence of a double load compart-
ment, first lift the upper cover and then the luggage
compartment mat).
❍unscrew the locking device B - fig. 10;
❍take out the tool box C and place it next to the wheel
to be changed;
❍take out the space-saver wheel D - fig. 10;
❍use the provided screwdriver to remove the hub cap,
levering the dedicated opening on the outer edge;
195-232 Delta GB 1ed 02/09/13 09.35 Pagina 206

6
TECHNICAL SPECIFICATIONS
257
Identification data ...........................................................258
Engine codes - bodywork versions....................................260
Engine ............................................................................261
Fuel supply system ..........................................................262
Transmission ...................................................................262
Brakes.............................................................................263
Suspension ......................................................................263
Steering ..........................................................................263
Wheels ............................................................................264
Dimensions .....................................................................269
Performance ...................................................................270
Weights ...........................................................................271
Capacities .......................................................................272
Fluids and lubricants ......................................................273
Fuel consumption ...........................................................275
CO
2emissions .................................................................276
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 257

258
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA The vehicle identification details are, fig. 1:
1 V.I.N. plate (located in the engine compartment, to the
side of the right shock absorber upper mounting);
2 Bodyshell marking (located on the passenger compart-
ment floor, next to the passenger side front seat);
3 Bodywork paint identification plate (located on the in-
side of the tailgate);
4 Engine marking (located on the left rear section, gear-
box side).V.I.N. PLATE fig. 2
This plate is fitted to the engine compartment front cross-
member and contains the following data:
B Type-approval number
.
CVehicle type identification code.
D Chassis number.
EMaximum authorised weight of vehicle fully laden.
FMaximum authorised weight of vehicle fully laden plus
trailer.
GMaximum authorised weight on first axle (front).
HMaximum authorised weight on second axle (rear).
I Engine type.
L Bodywork version code.
M Spare parts number.
N Correct value of smoke coefficient (for diesel engines)
fig. 1
L0E0116m
fig. 2
L0E0117m
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 258

TECHNICAL SPECIFICATIONS
271
6
1410
570
1090
950
1980
1300
500
80
60
WEIGHTSWeights (kg) 1.6 Multijet 105/120 HP
Unladen weight (with all fluids, fuel tank filled to 90% and without optional equipment)Payload (*) including the driver:
Maximum permitted loads (**)
–– front axle:
–– rear axle:–– total:
Towable loads
– braked trailer:– non-braked trailer:Maximum load on roof:
Maximum load on the ball joint
(braked trailer):(*) If special equipment is fitted (sun roof, tow hook, etc.) the unladen weight increases and consequently the payload will de-
crease, still complying with the maximum allowed loads.
(**) Loads not to be exceeded. The user is responsible for arranging goods in the luggage compartment and/or load platform with-
in the maximum permitted loads.
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 271

TECHNICAL SPECIFICATIONS
275
6
FUEL CONSUMPTIONThe fuel consumption values given in the table below are
determined on the basis of the type-approval tests laid
down by specific European Directives.
The procedures below are followed for measuring con-
sumption:
❍urban cycle: cold starting followed by driving that sim-
ulates urban use of the car;
❍extra-urban cycle: frequent accelerating in all gears,
simulating extra-urban use of the car; speed varies be-
tween 0 and 120 km/h;
❍combined consumption: the weighting is around 37%
urban cycle and 63% extra-urban cycle.IMPORTANT The type of route, traffic situations, weath-
er conditions, driving style, general conditions of the car,
trim level/equipment/accessories, climate control system
use, load, roof rack, other situations that affect air drag
may lead to different fuel consumption levels than those
measured.
FUEL CONSUMPTION ACCORDING TO THE CURRENT EUROPEAN DIRECTIVE (litres x 100 km)
1.6 Multijet
105 HP
1.6 Multijet120
HP
Urban
5.5
5.6
Extra-urban
3.7
3.8
Combined
4.4
4.5
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 275

TECHNICAL SPECIFICATIONS
277
6
PRESCRIPTIONS FOR HANDLING THE VEHICLE AT THE END
OF ITS LIFELancia has been committed for many years to safeguarding the environment through the constant improvement of its
production processes and manufacturing products that are increasingly compatible with the ecosystem. To assure cus-
tomers of the best possible service in terms of respecting environmental laws and in response to European Directive
2000/53/EC governing vehicles at the end of their life, Lancia is offering their customers the opportunity of handing
over their vehicle* at the end of its life without incurring any additional costs.
The European Directive sets out that when the vehicle is handed over, the last keeper or owner should not incur any
expenses as a result of i
t having a zero or negative market value. In particular, in almost all European Union countries,
until 1 January 2007, vehicles registered after 1 July 2002 will be collected free of charge, whilst from 2007 collection
will be free of charge irrespective of the year of registration as long as the vehicle contains its basic components (in
particular, the engine and bodywork) and has no additional waste.
To hand your vehicle over at the end of its life without extra cost, go to one of our Lancia Dealerships or authorised
collection and scrapping centres. These centres have been carefully chosen to offer high quality service for the collec-
tion, treatment and recycling of vehicles at their end of life, respecting the surroundi
ng environment.
You can find further information on these collection and scrapping centres either from a Lancia Dealership or by call-
ing the freephone number 00800 526242 00 or on the Lancia website.
* Ve hicle for transporting passengers with a maximum of nine seats with a total permitted weight of 3.5 t
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 277