9
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFET Y WARNINGS.
*IF EQUIPPED Blind Spot Detection / Lane Change Assist
1st-stage alert: When another vehicle is detected within the
BSD System boundary, a yellow light will illuminate on the
outside rearview mirrors.
2nd-stage alert: When 1st stage alert is on and a turn signal is
turned on, an alarm will sound.
RCTA (Rear Cross Traffic Alert)
When the vehicle is in Reverse and moves backwards from a
parking position, the sensor detects approaching vehicles on
the left or right side.Blind Spot Detection (BSD) System* The BSD system uses radar sensors to help alert the
driver while changing lanes or while in Reverse moving
backwards.
When the BSD button is pressed ON, the BSD indicator
on the button
A
will illuminate. The outside rearview
mirror warning lights will also illuminate for 3 seconds.
The system will become active when the vehicle is
traveling more than 18 mph and will alert the driver if
another vehicle is detected by the radar sensor.
A
Blind Spot Detection
System Video
To view a video on your
mobile device, snap this
QR code or visit the listed
website.
Refer to page 2 for more
information.www.KuTechVideos.com/vg13/2014
REMINDER:
• The BSD system will not show a warning if the vehicle speed is only 6mph above the surrounding vehicles
• When the BSD is ON and the ignition is cycled to OFF then ON again, the BSD system returns to ON
• The RCTA feature can be turned OFF/ON in User Settings
For more information on the Blind Spot Detection System, please refer to the Owner’s Manual.
QUICK TIPS
DRIVER’S PANEL
OPTIMA
FEATURES & FUNCTIONS GUIDE
34
*IF EQUIPPED
•
• You can reprogram a single HomeLink
® button by repeating Step 2
• Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
The Auto-Dimming Rearview Mirror is designed to reduce
glare from a vehicle’s headlights located in the rear and also
connect up to three electronic transmitters in one location.
To turn automatic dimming ON or OFF, press button
F
HomeLink
® with Auto-Dimming
Rearview Mirror*
How to Sync Transmitter with HomeLink
®*
Erasing programmed buttons:
A HomeLink
® button
B HomeLink
® button
C Indicator lightD HomeLink
® button
E Glare detection sensor F Automatic dimming ON/OFF G Compass control buttonH Compass displayIf programming for the first time, begin with Step 1
(repeating this step will delete all information).
To program non-rolling and rolling code garage door
openers and other devices:
1. Press and hold the left
A and center
D buttons
simultaneously until the indicator light C begins to
flash (to reprogram buttons, skip this step)
2. Press and hold the desired button
A B D and hold
the button on the transmitter while it is approximately
1 to 3 inches away from the mirror. The HomeLink
®
Indicator light
C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers,
complete these steps:
3. Locate the “learn” or “smart ” button on the garage
door’s motor head unit. Press and release the button
and complete Step 4 within 30 seconds
4. Firmly press, hold for two seconds, and release the
programmed HomeLink
® button up to three times
Press and hold the left
A and center
D buttons
simultaneously for approximately 20 seconds,
and then release both buttons within 30 seconds.Operating HomeLink
®:
Press one of the programmed HomeLink
® buttons.
REMINDER: Mirror indicator light
C will illuminate when automatic
dimming is ON.
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink
® system, you may need to
purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515 .
A
B
C
D
E
F
G
H
OTHER KEY FEATURES
