12
first drive features
TO RETURN THE 2ND ROW SEATS TO THE
STANDARD POSITION:
1.
Return the carpet panel flap to the back side of the
seatback and secure it in place.
2.
Pull the seat reclining lever B up while you lift up
and push back on the seatback until it locks in place.
3.
Return the seat bottom backward to its original
position until it locks in place.
4.
Use the seat reclining lever to adjust the seat to the
desired position.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system (sectio\
n 1) ” section of your
Owner’s Manual.
3rd Row Power Folding Seats
The 3rd row seats can be folded flat for maximum
cargo hauling or extra storage space.
Before folding down the 3rd row seats:
•
The vehicle’s shift lever must be in
P (PARK)
or N (NEUTRAL).
•
Place the seat belt buckles in the storage of the seat
cushion
01 to avoid dropping them under the seat
cushion or causing damage to your leather seats.
•
Disconnect and secure the center seat belt and
tongues into the retractor base
02.
1. To release the seat belt connector tongue, insert
a suitable tool (a key, for example) into the
opening on the side of the connector buckle.
2.
Retract the seat belt up to the retractor base located in the rear ceili\
ng storage area.
3.
Insert the seat belt tongue into the fabric sleeve
so that it will lay flat.
4.
Secure the connector tongue into the retractor base.
5.
Always reconnect the center seat belt when the
seat is returned to the upright position.
•
Make sure that there are no objects on the
seat cushion.
• Lower the 3rd row head restraints.
To lower the seat, push and hold the front portion A
of the right or left 3rd row power folding seat switch 01.
To return the seats to an upright position, press the back
portion
B of the right or left 3rd row power folding seat switch 01.
For more information, refer to the “Safety –– Seats, seat belts and supplemental restraint system (se\
ction 1) ” of
your Owner’s Manual.
01
3.2.
B
02
01
B A
B A
1591592_14b_Infiniti_QX80_QRG_093013.indd 129/30/13 9:36 AM
20
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
The Intelligent Cruise Control (ICC) system
automatically maintains a selected distance from
the vehicle traveling in front of you according to that
vehicle’s speed (up to the set speed) or at the set
speed when the road ahead is clear.
This system may not function properly due to
road conditions when direct sunlight, rain, mud,
snow or other road spray cause the sensor to
become blocked.
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
01 for less than 1.5
seconds. The indicator light
02 will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch 03 and release it. Cruise control
will be set to the desired speed.
Press the distance button 04 repeatedly to change the set distance
between long, middle, and short.
When a vehicle is not detected ahead of you in the lane, the set distanc\
e and set vehicle
speed indicator lights will illuminate
05 in set mode.
When a vehicle is detected ahead of you in the lane, t he vehicle ahead detection, set
distance, and set vehicle speed indicator lights will illuminate
06 in set mode.
TO SET CONVENTIONAL FIXED SPEED CRUISE CONTROL MODE:
While cruise control is off, press the CRUISE ON/OFF button and hold it down for more than
1.5 seconds. The CRUISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
TO SWITCH BETWEEN THE TWO CRUISE CONTROL MODES:
When one of the two cruise modes is in use, you must turn the system off\
, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
03
01
04
0205
06
1591592_14b_Infiniti_QX80_QRG_093013.indd 209/30/13 9:36 AM
