2014 INFINITI Q70 HYBRID tire type

SAFETY WARNINGS
Property damage, serious injury or death may result from:●TIRE FAILURE DUE TO UNDERINFLATION/
OVERLOADING/ MISAPPLICATION.
Follow the vehicle Owner’s Manual or tire placard in
vehicle.
●TIRE FAILURE DUE TO IMPACT DAMAGE/IMPROPER
MAINTENANCE.
Tires should be inspected regularly by a qualified
technician for signs of damage, such as punctures or
impacts.
●TIRE FAILURE DUE TO IMPROPER REPAIRS.
See Rubber Manufacturer’s Association (RMA) es-
tablished repair procedures at www.rma.org and/or
go to www.goodyear.com for information on proper
repair procedures.
●EXPLOSION OF TIRE/RIM ASSEMBLY DUE TO
IMPROPER MOUNTING.
Only specially-trained persons should mount tires.
When mounting tires, use safety cage and clip-on
extension air hose to inflate.
●FAILURE TO MOUNT RADIAL TIRES ON APPROVED
RIMS.
●FAILURE TO DEFLATE SINGLE OR DUAL ASSEMBLIES
COMPLETELY BEFORE DEMOUNTING.
●TIRE SPINNING.
On slippery surfaces such as snow, mud, ice, etc., do
not spin tires in excess of 35 mph (55 kph), as indi-
cated on the speedometer.
●EXCESSIVE WHEEL SPINNING.This can also result in tire disintegration or axle failure.
WARNING: Vehicle handling, traction, ride comfort and
other performance parameters may be significantly af-
fected by a change in tire size or type. Before replacing
tires, always consult and follow the vehicle Owner’s
Manual because some vehicle manufacturers prohibit
changing tire size. When selectin g tires that are different
from the original equipment size make certain: (1) The
tires have adequate load carrying capacity based on the
vehicle placard, (2) The tires have sufficient inflation
pressure to carry the load and (3) There is proper clear-
ance with no interference points between the tire and
vehicle. The consumer must be aware to always drive
safely and obey all traffic laws. Avoid sudden, sharp
turns or lane changes. Failure to follow any of these
warnings may result in loss of control of the vehicle,
leading to an accident and serious injury or death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way t o help ensure satisf actory mileage and
performance from your Goodyear or Dunlop tires is to
give them a simple but frequent (at least monthly) in-
spection for proper inflation, ev en treadwear, and the
presence of any damage.
DO MAINTAIN PROPE R INFLATIONPRESSURE
IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire
performance, safety and fuel economy. Check inflation
pressures at least once a month and before long trips. Use
an accurate tire pressure gauge. Always check pressures
when the tires are cold (when the vehicle has been driven
less than one mile). If you must check inflation when the tires are hot, add 4 psi (27 kPa) to the recommended cold
inflation pressure. It is difficult to tell just by looking at
radial tires whether they are underinflated.
*
Furthermore, when operating a vehicle equipped with
radial tires, it is difficult to notice when a tire has gone
flat or nearly flat since the “feel” of the vehicle does not
change significantly.
Progressive air loss may result from punctures, cuts,
curbing, impacts or partial bead unseating. Some fit-
ment causes for air loss are (1) incomplete bead seat-
ing, (2) bead tearing caused by a machine tool due to
insufficient lubrication or improper adjustment, (3)
leaking valve core or rubber valve components should
be replaced when problems are detected and whenever
tires are replaced.
Always maintain inflation pressure at the level recom-
mended by the vehicle manufacturer as shown on the
vehicle placard, vehicle certification label or in the ve-
hicle Owner’s Manual:
Underinflation is the leading cau
se of tire failure and
may result in severe cracking, component separation or
“blowout.” It reduces tire load capacity, allows exces-
sive sidewall flexing and increases rolling resistance,
resulting in heat and mechanical damage. Maintaining
proper inflation pressure is the single most important
thing you can do to promote tire durability and maxi-
mize tread life.
Overinflation increases stiffness, which may deteriorate
ride and generate unwanted vibration. Overinflation
also increases the chances of impact damage.
(Continued on next page)
* Evidence of air loss or repeated underinflation always requires expert ins pection to determine the source of leakage and tire removal to determine repairability. To avoid injury, NEVER
attempt to reinflate a tire that has been run severely underinflated.
28 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

DON’T OVERLOAD YOUR VEHICLE OR TIRES
Check your vehicle Owner’s Manual to determine the
load limits. Overloading your vehicle places stress on
your tires and other critical vehicle components. Over-
loading a vehicle can cause poor handling, increased
fuel consumption and may cause tire failure. Overload-
ing your tires can result in severe cracking, component
separation or blowout.
Never fit your vehicle with new tires that have less load
capacity than shown on the vehicle tire placard and
remember that optimum rim width is important for
proper tire load distribution and function.
The maximum load capacity stamped on the sidewalls
of P-Metric & European Metric tires is reduced by 10%
when used on a light truck, utility vehicle or trailer.
Never fit P-Metric or European Metric tires to light trucks
that specify LT-type replacement tires.
DON’T SPIN YOUR TIRES EXCESSIVELY
Avoid excessive tire spinning when your vehicle is stuck
in snow, ice, mud or sand. The centrifugal forces gener-
ated by a free-spinning tire/wheel assembly may cause
sudden tire explosion resulting in vehicle damage
and/or serious personal injury to you or a bystander.
Never exceed 35 mph/55 km/h, as indicated on your
speedometer. Use a gentle backward and forward rock-
ing motion to free your vehicle for continued driving.
Never stand near or behind a tire spinning at high
speeds. For example, while attempting to push a vehicle
that is stuck or when an on-the-car spin balance ma-
chine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when they reach two
thirty-seconds of an inch (2/32) remaining tread depth.
All new tires have treadwear indicators which appear as
smooth banks in the tread grooves when they wear to
the two thirty-seconds of an inch (2/32) level. Many wet
weather accidents result from skidding on bald or nearly
bald tires. Excessively w orn tires are also more suscep-
tible to penetrations.
DO CHECK YOUR TIRES FOR DAMAGE
Frequent (at least monthly) inspection of your tires for
signs of damage and their general condition is impor-
tant for safety. If you have any questions, have your tire
Retailer inspect them. Impacts, penetrations, cracks,
knots, bulges or air loss always require tire removal and
expert inspection. Never perform a temporary repair or
use an inner tube as a substitute for a proper repair.
Only qualified persons should repair tires.
PROPER TIRE REPAIR
NOTE: Goodyear and Dunlop do not warrant any inspec-
tion or repair process. The repair is entirely the respon-
sibility of the repairer and should be made in accor-
dance with established Rubber Manufacturers
Association (RMA) procedures.
TIRE PRESS URE MONITORING SYSTEM ALERT
Refer to your vehicle Owner’s Manual for more informa-
tion on what to do if the tire pressure warning system
activates.
THE CONVENIENCE (TEMPORARY) SPARE
The Convenience (Temporary) Spare is designed, built,
and tested to the high engineering standards set by
North America’s leading car manufacturers and to
Goodyear and Dunlop’s own high standards of quality
control. It is designed to take up a minimum of storage
space and, at the same time, fulfill the function of a
spare tire when needed. The spare is kept in its storage
space, fully inflated at 60 psi. To be sure it is always
ready for use, the air pressure should be checked on a
regular basis.
The Convenience (Temporary) Spare can be used in
combination with the original tires on your vehicle. You
can expect a tire tread life of up to 3,000 miles
(4,800 kilometers), depending on road conditions and
your driving habits. To conserve tire tread life, return the
spare to the storage area as soon as it is convenient to
have the standard tire repaired or replaced.
The Convenience (Temporary) Spare weighs less than a
standard tire so it’s easier to handle. It also helps re-
duce the total car weight which contributes to fuel
economy.
The wheels used with the Convenience (Temporary)
Spare are specifically designed for use with high pres-
sure spares and should never be used with any other
type tire.
(Continued on next page)
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY 29

DON’T ATTEMPT TO MOUNT YOUR OWN TIRES
Serious injury or Death may result from explosion of tire/
rim assembly due to improper mounting procedures. Fol-
low tire manufacturer’s instructions and match tire diam-
eter to rim diameter. Mount light truck radials on rims
approved for radial service. Do not apply bead sealer. This
can inhibit bead seating. Lubricate beads and tire rim
(including tube or flap) contact surfaces. Lock assembly
on mounting machine or place in safety cage. STAND BACK
and never exceed 40 psi to seat beads. Never use a volatile
substance or a rubber “donut” (also known as a bead
expander or “O-Ring”) to aid bead seating. Only specially-
trained persons should mount tires.
DON’T MIX TIRES OF DIFFERENT SIZES AND
TYPES ON THE SAME AXLE
For optimum handling and control, Goodyear and Dun-
lop recommend fitment of four (4) tires of the same type
and size unless otherwise specified by the vehicle
manufacturer.
WARNING: Before you replace your tires, always consult
the vehicle Owner’s Manual and follow the vehicle
manufacturer’s replacement tire recommendations. Ve-
hicle handling may be significantly affected by a change
in tire size or type. When selecting tires that are different
than the Original Equipment size, see a professional
installer in order to make certain that proper clearance,
load carrying capacity and inflation pressure is se-
lected. Never exceed the maximum load capacity and
inflation pressure listed on the sidewall of the tire. Al-
ways drive safely and obey all traffic laws. Avoid sud-
den, sharp turns or lane changes. Failure to follow this
warning may result in loss of control of the vehicle,
leading to an accident and serious injury or death. When replacing tires, you must maintain the outside
diameter and load carrying capacity of the Original
Equipment tire. Inflation pressure may need to be ad-
justed to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or
JATMA standards for correct load and inflation informa-
tion.
NEVER FIT TIRES TO A VEHICLE THAT HAVE
LESS LOAD CARRYING CAPACITY THAN AS
REQUIRED BY THE ORIGINAL EQUIPMENT
MANUFACTURER
Examples: Many vehicles, such as large passenger
vans, require Load Range E tires as designated by the
vehicle manufacturer. Fitment of a tire, such as a Load
Range D, with less carrying capacity is not allowed.
In other cases, tires of the same size may carry different
load indexes in the service description. You must make
certain the replacement tires fitted to the vehicle have a
load carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.
FOLLOW THESE ADDITIONAL GUIDELINES
NOTE:
Goodyear manufactured and/or marketed European-
Metric passenger tires and P-Metric passenger tires are
interchangeable as long as they have the same section
width, same aspect ratio, same rim diameter.
CAUTION
Never substitute a “Standard Load” (SL) tire for
an Extra Load (XL) tire. If the vehicle was origi-
nally equipped with “Extra Load ” (XL) tires, re-
place those tires with similar sized XL tires.
When installing only two tires, fit the tires with the
deepest tread depth on the rear axle. If radials and
non-radials must be fitted to the same vehicle, fit radials
on rear axle. Never mix radials and non-radials on the
same axle. When fitting snow tires or all-season tires to
performance vehicles, always fit in sets of four. It is not
recommended to fit tires with different speed ratings. If
tires with different speed ratings are installed on a ve-
hicle, they should be installed with like pairs on the
same axle. The speed capability of the vehicle will be-
come limited to that of the lowest speed rated tires.
Use of lift kits with some vehicle/tire combinations can
cause instability. When changing tire sizes, always con-
sult Retailer for optimum rim width and carefully check
vehicle/tire clearances.
RETREADED TIRES
Retreaded passenger and light truck tires are not war-
ranted by Goodyear and Dunlop for any reason. Good-
year and Dunlop speed ratings and U.S. Department of
Transportation test compliance certifications are voided
for retreaded tires.
(Continued on next page)
30 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

HAZARDS
Objects in the road that threaten a tire should be safely
avoided. These objects arepotholes, glass,metal,
rocks, wood debris and the like. Unavoidable contact
should prompt a thorough tire inspection.
You may not always recall hitting an object that can
damage or injure your tires. If while driving your vehicle
experiences any unusual vibrations, ride disturbance or
noise and/or you suspect that possible damage to the
tires or vehicle has occurred, DO NOT JAM OR LOCK YOUR
BRAKES! Rather reduce your speed and drive with cau-
tion until you can safely pull off the road. Stop and
inspect the tires. If the tire is underinflated or damaged,
deflate, remove the tire and rim assembly and replace it
with your spare. If you cannot detect a cause, have the
vehicle towed to the nearest vehicle or tire retailer to
have the vehicle inspected.
REPAIRING, MOUNTING AND DEMOUNTING
OF TIRES
Do not attempt to repair, mount or demount a tire your-
self. Tire changing can be dangerous and must be done
by professionally trained persons using proper tools
and procedures as specified by the Rubber Manufactur-
ers Association (RMA). Follow these mounting recom-
mendations. Your tires should be mounted on wheels of
correct size and type and which are in good, clean con-
dition. Bent, chipped or rusted wheels may cause tire
damage. The inside of the tire must be free from foreign
materials. Have your retailer check the wheels before
mounting new tires. Mismatched tires and rims can
explode during mounting. Also, mismatched tires and
rims can result in dangerous tire failure on the road. If a
tire is mounted by error on the wrong-sized rim, do not remount it on the proper rim - scrap it. It may be dam-
aged internal
ly (which is not extern ally visible) by being
dangerously stretched and could fail on the highway.
Old valves may leak. When new tubeless tires are
mounted, have new valves of the correct type installed.
Tubeless tires must be mounted only on wheels de-
signed for tubeless tires, i.e., wheels which have safety
humps or ledges.
Never perform a temporary repair, use an innertube or
inject sealant as a permanent substitute for a proper
repair. Only qualified persons should repair tires.
Be sure that all your valves have suitable valve caps.
This will keep valve cores clean and clear and guard
against leakage.
REPAIRS - WHENEVER POSSIBLE, SEE A TIRE RETAILER
AT ONCE. Some tire manufacturers do not warrant any
inspection or repair process. The repair is entirely the
responsibility of the repairer. Punctures in the tread of a
passenger tire which do not exceed 1/4 of an inch
(6mm) in diameter can usually be repaired by following
the Rubber Manuf acturer’s Association (RMA)Passen-
ger and Light Truck Repair procedures. Contact the
manufacturer of your tires for it s position and assistance
as to the acceptable location for a proper repair and the
repair of speed rated tires. Do not use plug repairs. They
may cause further damage to the tire. They are not
always air tight and the plug may fail. Do not exceed
posted speed limits on any repaired tire. Certain tire
manufacturers speed ratings are voided if the tire is
repaired. Although a tire was properly repaired, internal structural
damage resulting from the puncture may have occurred.
Sometime later the damage may cause the tire to be
removed from service.
If the tire has a puncture in the tread which exceeds
1/4 inch (6mm), the tire must be replaced. If any tire has
sustained a puncture, have the tire inspected internally
by a tire retailer for possible damage that may have
occurred.
Improper mounting and inflation procedures can cause
an explosion of the tire/rim assembly. Only specially
trained persons should perform these tasks. Contact
your tire store or retailer for assistance.
CAUTION - Never, under any c
ircumstance, introduce a
flammable substance into a tire.
WHEEL ALIGNMENT AND BALANCING
Wheel alignment and balancing are important for safety
and maximum mileage from your tires. Check how your
tires are wearing at least once a month. If your tires are
wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect
excessive vibration, your vehicle may be out of align-
ment or balance. These conditions not only shorten the
life of your tires, but adversely affect the handling char-
acteristics of your vehicle which could be dangerous. If
you detect irregular wear or vibration, have your align-
ment and balance checked immediately. Tires which
have been run underinflated will show more wear on the
shoulders than in the center of the tread.
(Continued on next page)
50 IMPORTANT TIRE SAFETY INFORMATION1

HARD BRAKING
You must inspect your tires after any hard braking cir-
cumstances or after tires have slid on the pavement.
This can cause a flat spot in a section of the tire tread.
TIRE SPINNING
Never spin your tires above a speedometer reading of
35 mph (55 km/h) if your vehicle becomes stuck. The
centrifugal force generated by the free spinning
tire/wheel assembly may cau se a sudden tire explo-
sion, resulting in vehicle damage and/or serious per-
sonal injury or death. Never allow anyone to stand near
or behind a tire spinning at high speed while attempting
to push a vehicle that is stuck. When in mud, sand,
snow, ice or other slippery conditions, do not indulge in
excessive wheel spin. In such conditions, with auto-
matic tran smission vehicles , by accelerating the engine
excessively, it is possible to spin one of the drive tires
beyond its speed capability. This is also true when bal-
ancing a drive tire/wheel assembly using the engine of
the vehicle to spin the wheel.
TIRE TREAD
Tires must be replaced when the depth of the tread
reaches 2/32 inch (1.6 mm). Tires are manufactured
with tread wear indicators molded into the tire grooves
which indicate tread wearout. As tires approximate
2/32 inch (1.6 mm) wearout, the tread gauge becomes
thinner and more vulnerable to the effects of road haz-
ards. Also, worn tires are more subject to hydroplaning,
which can cause loss of control. Therefore, visual tire
inspection becomes more crucial as the tires wear out.
WORN TIRES
Never drive on worn tires. Tires should be replaced by
trained personnel when 2/32nds of an inch tread depth
remains, as indicated by the tread wear indicators molded
into the tread grooves. In most states, it is illegal to drive
with less than 2/32nds of an inch of tread remaining.
TIRE MIXING
For best performance select tires similar in size and load
rating to the original equipment tires. It is recom-
mended that the same size and type of tire be used on
all four wheel positions. In certain tires, casing ply ma-
terial and ply construction may vary as indicated on the
sidewall of the tire. When changing or replacing tires, it
is preferred that all four tires are the same construction
type (i.e., High Performance, All Season, Mud & Snow)
and construction (Radial or Bias Ply). Before mixing tires
of different types on a vehicle in any configuration, be
sure to check the vehicle Owner’s Manual for its recom-
mendations.
Tires which meet the Rubber Manufacturer’s Associa-
tion (RMA) definition of mud and snow tires are marked
M/S, M+S, M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are
not recommended for mud and/or snow driving.
If snow tires are needed, it is necessary to select tires
equivalent in size and load rating to the original equip-
ment tires. Always fit performance snow tires in sets of
four (4) for optimum mud & snow traction and mainte-
nance of vehicle handling characteristics. If you do not,
it may adversely affect the safety and handling of your
vehicle. It is also important to check the vehicle Owner’s
Manual before mixing or matching tires on 4-wheel drive
vehicles as this may require special precautions. Please refer to your Owner’s Manual for more informa-
tion on tire replacement precautions.
TIRE ROTATION
Tires on your Infiniti vehicle should be rotated every
7,500 miles or as irregular wear develops. If irregular
wear becomes apparent or if the wear rate on the tires is
perceptibly uneven, the tires should be rotated in such a
way to alleviate the problem. Check your vehicle for any
mechanical problems and correct if necessary. Any rota-
tion pattern or procedure may be followed including
those indicated in the Owner’s Manual. Some tires have
arrows on the sidewall showing the direction in which
the tire should turn. When rotating this type of tire, care
must be taken to maintain the proper turning direction
as indicated by the arrows.
Some vehicles have different
tire sizes specified for front and rear axles. Tires on these
vehicles should not be rotated side to side (unless they
are non-directional) . Where a temporary type spare tire
is available, it should not be included in the tire rotation
schedule. Such tires are intended for temporary use
only.
REPLACING TWO TIRES
If your vehicle was originally equipped with four tires
that were the same size and you are only replacing two
of the four tires, install the new tires on the rear axle.
Placing new tires on the front axle may cause loss of
vehicle control in some driving conditions and cause an
accident and personal injury.
(Continued on next page)
IMPORTANT TIRE SAFETY INFORMATION151

TRAILER TOWING
If you anticipate towing a trailer, you should see a tire
retailer for advice concerning the correct size of tire and
pressure. Tire size and pressure will depend on the type
and size of the trailer and hitch utilized, but in no case
must the maximum cold inflation pressure or the tire load
rating be exceeded. Check the tire decal and your Owner’s
Manual for further recommendations on trailer towing.
TIRE ALTERATIONS
Do not perform any alterations on your tires. Alterations
may prevent proper performance, leading to tire dam-
age, which can result in an accident. Tires which be-
come unserviceable due to alterations such as truing,
whitewall inlays, addition of balancing or sealant liq-
uids, may be excluded from warranty coverage. Consult
your tire warranty.
HIGH PRESS URE TEMPORARY SPARE TIRES
1) The high-pressure spare tire in your Infiniti ve-
hicle is designed for temporary use only and
must not be used continually as a regular tire.
The standard tire should be repaired and/or
replaced as soon as possible.
2) Avoid driving over obstacles that may damage the tire through impact or cutting, such as
potholes, g lass,metal, etc.
3) Speed must not exceed 50MPH (80km/h) for non-speed-rated temporary spare tires. 4) Temporary spare tires have a limited treadlife
which can vary depending on road conditions
and your driving habits. The spare tire should
be returned to the trunk as soon as the stan-
dard tire can be repaired or replaced.
5) Because the high-pressure spare tire was spe- cifically designed for your car, it should not be
used on any other vehicle.
6) Do not use snow chains on your high-pressure spare. This could cause damage to your
vehicle.
7) Check the tire’s cold inflation pressure monthly and maintain at 60psi (4.2kg/cm2) even when
not in use.
8) The high-pressure spare tire should not be used with any other rim nor should standard
tires, wheel covers, or trim rings be used on the
high-pressure spare tire rim which was origi-
nally installed.
9) When the tread wear indicator appears on the tire, replace it only with the same type spare
tire.
10) Do not enter an automatic carwash with a tem- porary spare tire fitted.
11) Do not make a sharp turn or apply the brakes suddenly when driving on a high-pressure tem-
porary spare.
Note: When using any temporary type spare
tire, be sure to follow the vehicle Own-
er’s Manual instructions.
TIRE STORAGE
All tires should be stored in a cool dry place indoors so
that there is no danger of water collecting inside them.
When tires are stored they should be stored in a cool
place away from sources of heat and ozone such as hot
pipes and electric generators. Be sure that surfaces on
which tires are stored are clean and free from grease,
gasoline or other substances which could deteriorate
the rubber. (Tires exposed to these materials during
storage or driving could be subject to sudden failure.)
To Avoid Damage to your Tires and Possible
Accident:
● Check tire pressure at least once a month when
tires are cold and before long trips.
● Do not underinflate/overinflate.
● Do not overload.
● Drive at moderate speeds, observe legal limits.
● Avoid driving over potholes, obstacles, curbs or
edges of pavement.
● Avoid excessive wheel spinning.
● If you see any damage to a tire, replace with spare
and see the tire manufacturer’s retailer or your
Infiniti retailer .
For further information, the Consumer Tire Guide on
passenger tire care, safety and mileage performance is
available in the United States by writing the Tire Indus-
try Safety Council, Box 1801, Washington, D.C. 20013.
52 IMPORTANT TIRE SAFETY INFORMATION1

ROADSIDE ASSISTANCE
As part of theInfiniti Total Ownership Experience ® ,
Roadside Assist ance is available to you, 24 hours a day,
365 days a year, for emer gency roadsideassistance
should the need arise for any of the following items:
●Mechanical Breakdown
●Flat Tire
●Accident/Collision (One-way tow – loaner vehicle not
included)
●Out of Gas
●Lock-out service
●Dead 12V Battery
All Roadside Assist ance services are provided exclu-
sively by Cross-Country Motor Club, Inc., Boston, Mas-
sachusetts 02155, except in Alaska, California, Oregon,
Wisconsin and Wyoming, where services are provided
by Cross-Country Motor Club of California, Inc., Boston,
Massachusetts 02155.
HOW TO USE ROADSIDE ASSISTANCE
Should one of the disablements listed above occur,
simply call the toll free number, 1-800-662-6200, and
advise the Roadside Assistance Representative of your
name, the vehicle identification number (VIN) of your
car, your location, and the nature of the problem. (When
travelling in Canada call 1-800-835-0221.) The VIN can
be found imprinted on a plate affixed to the upper
dashboard on the driver’s side of your Infiniti. The VIN is
also printed on the permanent Infiniti Total Ownership
® Program card which will be sent to you approximately
6 weeks after purchase of your new Infiniti.
COVERAGE
Roadside Assistance is provided for all Infiniti vehicles
from the date the vehicle is delivered to the first retail
buyer or otherwise put into use, whichever is earlier, for
a period of 48 months, without regard to mileage.
Roadside Assistance is available to an yone operating
the Infiniti vehicle with the authorization of the owner.
[For purpose of Roadside Assist ance benefits, “owner”
includes the lessee of a leased vehicle.] These services
are transferable with the resale of the vehicle for the
time remaining on the original Infiniti new vehicle lim-
ited warranty coverage period. Roadside Assistance is
available throughout the Continental United States and
Canada.
ON-SITE AND TOWING SERVICE
Depending on the type of vehicle problem you are expe-
riencing, the R oadside Assistance Represent ative will
determine the appropriate roadside assistance and/or
flatbed (towing) service to be dispatched. In most
cases, minor disablement services such as flat tire
change, lock-out service, out-of-gas delivery, etc., can
be performed onsite so that you can be on the road
again as soon as possible. There is no charge for the
dispatch of onsite or towing service. Any charges for the
replacement of keys, gas or non-warranty items will be
your responsibility at the time of the repair or service.
Whenever possible, flatbed (towing) service will be dis-
patched for mechanical disablements or accident/ col-
lisions which render the vehicle inoperative. There is no
charge for the towing service. Roadside Assistance will
arrange to transport the vehicle to the nearest Infiniti
retailer , if one is located within 250 miles, or to another
authorized alternate service facility. Warranty covered repairs will be provided for under the terms of the appli-
cable express Infiniti limited warranty. However, any
nonwarranty or accident/collision repairs will be your
responsibility.
NOTE:
You may be required to sign a receipt at the time of
disablement to acknowledge receipt of the Roadside
Assistanc
e service rendered.
EXCLUSIONS
Roadside Assistance is not a warrantyand is not pro-
vided under any Infiniti or Nissan warranty, butisa
service which is provided to you as part of the Infiniti
Total Ownership Experience ® to minimize any unfore-
seen vehicle operation inconvenience. Potential liabil-
ity is expressly limited to the cost of the listed benefits
and does not extend to incidental or consequential
damages such as loss of use inconvenience, loss of pay,
or commercial loss.
Roadside Assistance benefits exclude any costs related
to repairs, parts replacement, labor, etc. which are in-
curred as a result of accident/ collision, vehicle abuse,
racing, vandalism or other items not covered by the
Infiniti New Vehicle Limited Warranty. Also excluded are
services for snow tires, repair to studs, mounting or
demounting of snow chains, and any fines, fees or taxes
which are associated with impound towing as a result of
actual or alleged violation of any laws or regulations.
(Continued on next page)
INFINITI TOTAL OWNERSHIP EXPERIENCE ® BENEFITS 53