2014 INFINITI Q60 CONVERTIBLE light

12
first drive features
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 mph(40 km/h).
The system will automatically maintain the set speed



until you tap the brake pedal, accelerate, cancel or




turn the system off.

To activate the cruise control, push the ON/OFF
switch
01 . The C r UISE
indicator light in the
instrument panel will illuminate.
To set cruising speed, accelerate the vehicle to the desired speed, push the COAS t /
SE
t switch

02 and release. The C r UISE SE t indicator light
in the instrument panel will
illuminate. Take your foot off the accelerator pedal. y our vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCEL/ r ES switch
03 . When the

vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAS t /SE t switch
02 . Release the

switch when the vehicle slows to the desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch
04 .
To turn off cruise control, push the
ON/OFF switch
01 . The C r UISE
indicator light
in the

instrument panel will turn off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
02
0304
USB/iPod® Interface
The USB jack 01 is located in the center console under

the arm rest.
When a compatible USB memory device or iPod®
is plugged into the USB jack, compatible
audio and video files stored on the device
can be played through the vehicle’s audio
system and front display.
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.
01
1276473_14a_Q60_Convertible_QRG_062113.indd 126/21/13 3:31 PM

13
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the ON/OFF button

01 for less than 1.5 seconds.

The C
r
UISE indicator light
02 will illuminate.
Accelerate to the desired speed.
Push down on the
COAS t /SE t switch
03 and release

it. Cruise control will be set to the desired speed.
Press the distance button 04 repeatedly to change

the set distance between long, middle, and short.
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate
05 in set mode.
When a vehicle is detected ahead of you in the lane,

the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate
06 in

set mode.
To reset at a faster cruising speed, push up and hold the ACCEL/ r ES
switch
07 . When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push down and hold the
COAS t /SE t
switch
03 . Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator 05 will go out.
To turn off cruise control, press the
ON/OFF button
01 . The C r UISE indicator light
02 ,
in the instrument panel will turn off.
To set conventional (fixed speed) cruise control mode:
While cruise control is off, press the ON/OFF
button
01 and hold it down for more than 1.5
seconds. The C
r
UISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the
COAS t /SE t switch and release it. The SE t indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off\
, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
04
0807
03
01
0205
06
1276473_14a_Q60_Convertible_QRG_062113.indd 136/21/13 3:31 PM

19
Navigation System (if so equipped)
y our Navigation System can calculate a route from the current location to\
a preferred
destination. The real-time map display and turn-by-turn voice guidance w\
ill lead you along
the route.
The Navigation System will continually update your vehicle’s position\
. If you have deviated
from the original route, it will recalculate the route from your current\
location.
01 Touch screen display.
02 S t A t US – Press multiple times to display audio information, the air conditi\
oner status, fuel
economy or navigation directions.
03 Destination (DES t ) – Press to enter a destination.
04 ZOOM OUt – Press to view a wider area.
05 r OU t E
– Press to access guidance control functions such as guidance cancell\
ation, route
priority or waypoint setting on the route.
06 Infiniti Controller
•


EN
t E r – Press the EN
t E r button to select the highlighted item on the screen.



•

Center Dial – Turn the dial to highlight an item on the screen, adjus\
t a setting or adjust the

map scale.



•

Slide the controller (push upward/downward/leftward/rightward) to sele\
ct an item on the

screen, to adjust a setting or scroll the map in 8 directions.
07 Information (INFO) – Press to display the vehicle, traffic (if so equipped), weather \
(if so
equipped) or voice recognition information.
02
04
0910
05
03
06
1213
11
0708
01
1276473_14a_Q60_Convertible_QRG_062113.indd 196/21/13 3:32 PM

21
HomeLink® Universal Transceiver
The HomeLink® system can learn and consolidate the functions of up to 3 different
hand-held transmitters, operating items such as garage doors, property g\
ates, outdoor and
indoor lights or alarm systems.
To program the Homelink® Universal Transceiver:



•


Position the handheld transceiver 1-3 in (26-76 mm) away from the Home\
link® surface,
keeping the Homelink® indicator light in view.



•


Press and hold the desired Homelink® button and the handheld transmitter button
simultaneously until the Homelink® indicator light flashes slowly and then rapidly.



•


Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the Homelink® and observe the
indicator light:



•


A solid continuous light indicates the programing is complete and the Ho\
melink®
button will activate your device.



•


A blinking light that turns to a solid continuous light after 2 seconds \
indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete th\
e
programing process:



•

At the receiver of the device that you are programing to the Homelink®, press and
release the “learn” or “smart” button (the name may vary by\
manufacturer but it is
usually located near where the hanging antenna wire is attached to the u\
nit).
y ou have
approximately 30 seconds to initiate the following step.



•


Press and hold the programmed Homelink® button for 2 seconds and release.
Repeat the previous 2 steps up to 3 times to complete the programming pr\
ocess.
Homelink® should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink® website at
www.homelink.com or call 1-800-355-3515.
HOMELINK®
1276473_14a_Q60_Convertible_QRG_062113.indd 216/21/13 3:32 PM