2014 INFINITI Q50 Quick Reference Guide

7
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the engine. It is
important to make sure the Intelligent Key is with you (that
is, in your pocket or purse).



The operating range of the Intelligent Key is within



31.5 in (80 cm) from each request switch.



To lock the vehicle, push either door handle request
switch
01 once or press the
button
03 on
the key fob.
To unlock the vehicle, perform one of the
following procedures:



•
Touch the inside of the door handle
02 to unlock the

corresponding door. Pressing the request switch 01
while touching the inside of the door handle will unlock the
rest of the doors, or
•


Press the
button
04 on the key fob to unlock the driver’s

side door. Press the
button again; all other doors will unlock.
To release the trunk lid, press the button
05 for more than
1 second. Lift the trunk lid to access the trunk.
The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding the
button
06 for more than 1 second. Once activated, the panic alarm and headlights w\
ill stay
on for a period of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the



Intelligent Key operation, start the engine according


to the following procedure:
1.


Move the shift lever to the
P (P ARK ) position.



2.

Firmly apply the foot brake.




3.

Touch the ignition switch with
the Intelligent Key
and a chime will sound.
4.


Within 10 seconds after the chime sounds, push
the ignition switch while depressing the

brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3 )”, “Starting and driving (section 5)” and the
“Maintenance and do-it yourself (section 8 )” of your Owner’s Manual.
03
04
05
06
02
01

8
Trunk Lid Release
Use one of the following methods to open the trunk:
Push the trunk open request switch
01 for more than
1 second while carrying the INFINITI Intelligent



Key with you.
Press the trunk buttonHOLD on the Intelligent Key for
more than 1 second.
From inside the vehicle, push down on the trunk lid



release switch 02 on the instrument panel.
To completely disable all power to the trunk lid, push

the trunk release power cancel switch
03 to the OFF

position. While in this position, the trunk lid cannot be
opened with the trunk open request switch
01 , trunk

button
HOLD , or the trunk lid release switch
02 until
pushed to the ON position.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
Seat Adjustments
POWER SEAT ADJUSTMENTS
To slide the seat forward or backward, push the
control switch
01 forward or backward. To recline the seatback, push the switch
02
forward or backward.
SEAT LIFTER
To adjust the angle of the front portion or height of
the seat, push the front or rear end of the switch
01 up or down.
POWER LUMBAR SUPPORT (if so equipped)

To adjust the seat lumbar support, push the front or back end of the swi\
tch 03.
MANUAL LUMBAR SUPPORT (if so equipped)


To adjust the seat lumbar support, move the lever up or down.
SIDE SUPPORT (driver’s seat only) (if so equipped)
The driver’s seat side support adjusts the support on your torso.
Push the switch 04 away from you to loosen the support, or pull the switch
04 toward you
for more support.
MANUAL THIGH EXTENSION (if so equipped)
To slide the thigh extension forward or backward, pull up on the lever 05 under the front of
the seat and slide forward or backward, Release the lever to lock the se\
at in position.
For more information, refer to the “Safety – seats, seat belts and supplemental restraint system (se\
ction 1 )” of your Owner’s Manual.
01
02
03
first drive features
01
04
02
03
05

9
Heated Seats (if so equipped)
There are 2 ways to operate the heated seats:



1. By pressing the heated seat switch 01.



•


Every press of the switch allows you to cycle
through the 5 different modes of

AUTO – Hi –
Mid – Lo – OFF.



2.


While on the

CLIMATE control screen on the
lower display, touch the left or right heated seat
icon
02.



•


The Left or Right Seat Setting screen is
displayed with a list of the 5 different modes
of AUTO – Hi – Mid – Lo – OFF to choose from.



•


The indicator light on the heated seat switch
01 will illuminate when the system is in AUTO – Hi – Mid – Lo.



•


While in AUTO, the heated seats will turn on/off automatically, depending on
temperature conditions in the vehicle compartment.



•


To view which one of the 5 modes the system is in, press the CLIMATE
button
03
. This will bring up the CLIMATE control screen on the lower display. From here you
will see the heated seat icons
02 for the driver and passenger side, and below the
icon is the mode the system is in currently.
For more information, refer to the “Heater and Air Conditioner (section 3)” of your InTouch Owner’s Manual.
0202
03
0101
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.
Follow these procedures to set the memory positions:



•

Confirm the shift lever is in the
P (PARK) position.



•

Push the ignition switch to the
ON position.



•

Adjust the driver’s seat, steering column and outside mirrors to the \
desired positions
using the adjusting switches for each feature.



•
Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1
second.



•

The indicator light on the memory switch you select will illuminate for \
approximately
5 seconds.



•

The driver’s seat, steering column and outside mirror positions are n\
ow set to
your preference.
When you turn off your vehicle the driver’s seat, steering column, an\
d outside mirror positions
are automatically remembered and recalled the next time you log into you\
r vehicle.
For more information, refer to the “Pre-driving checks and adjustments (section 3 )” of your Owner’s Manual, and “Information and
Settings (section 8)” of your InTouch Owner’s Manual.

10
first drive features
Starting/Stopping the Engine
It is important to make sure the INFINITI Intelligent



Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP button to start



the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position and
apply the parking brake.
Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5 )” of your Owner’s Manual.
Outside Mirror Control Switch
To sel
ect the right or left side mirror, move the



control switch 01 right or left.
Adju
st each mirror to the desired position using



the switch 02.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the position

01 to turn on the front parking, side marker, tail, license

plate and instrument panel lights. Turn the switch to the
position
02 to turn on the headlights.
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it i\
s dark and off when it is
light. The system will keep the headlights on for a period of time after\
you turn the ignition off
and all doors are closed.
To activate the autolight system, turn the headlight control switch to t\
he AUTO position
03
t
hen push the ignition switch to ON. To deactivate the autolight system, turn the headlight



control switch to the

OFF,
01 or
position
02.
HIGH BEAM SELECT
To manually select the high beam function:
1.
Turn the headlight control switch to the
position 02.



2.


Push the headlight control switch 04 forward
to
select the high beam function. The blue indicator
01
03
02
04
05
02
01

11
06
light illuminates in the instrument panel.
Pull the headlight switch back to the original
position to select the low beam. The blue
indicator light turns off.
Pull and release the headlight control switch 05 to

flash the headlight high beams on and off.
HIGH BEAM ASSIST (if so equipped)
The high beam assist system will operate when
the vehicle is driven at approximately 22 MPH (35 km/h) and above. If \
an oncoming vehicle
or leading vehicle appears in front of your vehicle when the high beam is on, the headlights
will automatically be switched to the low beam.
Following the procedure below only activates the high beam assist system\
. This does not
necessarily turn on the high beam, even if there is no other traffic. Bo\
th ambient light and
traffic conditions have to be correct for the high beam to illuminate.
To activate high beam assist, turn the headlight control switch to the AUTO position
01 and
push the headlight control switch 04 forward to turn on the high beam. The high beam

assist indicator light will illuminate.
FOG LIGHT SWITCH
The headlights must be on and the low beams selected for the fog lights to operate.
Turn the switch (inside collar) to the
position
06 to turn the fog lights on.
Turn the switch (inside collar)
to the
OFF position to turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2 )” of your Owner’s Manual.
Windshield Wiper and Washer Switch
RAIN-SENSING AUTO WIPER SYSTEM (if so equipped)
Move the lever to the following positions to operate



the windshield wipers:

01 Mist (MIST) - One sweep operation of the wipers.
02 Auto (A UTO ) - Operates the rain-sensing wipers
intermittently. The intermittent speed can be
adjusted by twisting the time control ring
03 .
04 Low (LO) - Wipers operate at a continuous
low speed.
05 High (HI) - Wipers operate at a continuous
high speed.
06 Pull the lever toward you to activate the washer. The wipers will operate several times.
PULLING UP THE WIPER ARM
Quickly move the lever to the MIST 01 position twice.
This will place the wiper arms into the service position to allow remova\
l of the wiper blades.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
MIST
OFFINT
LO
HI
06
03
01
02
04
05

12
first drive features
Climate Controls
01 CLIMATE BUTTON
Press to display the CLIMATE control screen on the lower display.
02 DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS
Press the driver’s side temperature control buttons up for warmer air\
or down
for cooler air.
03 PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS
To manually adjust the passenger’s side temperature, press the passen\
ger’s side



temperature control buttons up for warmer air or down for cooler air.
04 FAN SPEED CONTROL
To manually adjust the fan speed, press the button or touch the key to increase




the fan speed. Press the button or touch the key to decrease the fan speed.
05 AUTO BUTTON
Press the AUTO button to turn the system on and the system will automatically control \
the
inside temperature (automatic cooling and/or dehumidified heating), ai\
r flow distribution
and fan speed.
06 MODE CONTROL
Press the button or touch the key in the center of the lower display to cycle through
the following air flow outlets:



Air flows from the center and side vents.



Air flows from the center, side and foot vents.



Air flows mainly from the foot vents.



Air flows from the defroster and foot vents.
06
04
05
02
06
04
100907
01
03
08
11
12
13

13
07 AUTO AIR RECIRCULATION KEY (if so equipped)
Touch to allow inside air recirculation and outside air circulation to s\
witch automatically
depending on the quality of the outside air.
08 INTAKE AIR CONTROL BUTTON
Pressing the intake air control button will cancel auto air recirculation 07
(if so equipped) until it is re-activated from the touch screen (see \
above). Press the
intake air control button
to manually control whether the interior air is recirculated,
or outside air is drawn into the vehicle. When the indicator light is on\
, interior air is
recirculated, outside odors are avoided, and interior vehicle temperatur\
e is most
effectively maintained.
The air recirculation mode cannot be activated when the air conditioner \
is in the front
defrosting mode
or the front defrosting foot vent mode .
09 A/C Key

Touch the A/C key to turn the air conditioner system on or off. This system helps coo\
l and
dehumidify the air inside the cabin and defog the windows.
10 DUAL KEY
Touch to turn the passenger’s side temperature controls on or off. Wh\
en the system
is on, the indicator light will illuminate. This function will allow the\
passenger’s side
temperature to be adjusted independently from the driver’s side by pr\
essing the
passenger’s side temperature control buttons
03.
11 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the defroster control button
to turn the system on. The A/C automatically turns

on when the defroster mode is selected. This features removes humidity f\
rom the air.
To defrost the front and side windows, set the temperature controls
02 and fan speed
controls 04 to their maximum settings.
12 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster switch
to turn the system on or off.

This function automatically turns off after approximately 15 minutes.
13 ON/OFF BUTTON
Press the ON/OFF button to turn the climate control system off.
For more information, refer to the “Instruments and controls (section 2 )” of your Owner’s Manual and the “Heater and Air Conditioner
(section 3)” of your InTouch Owner’s Manual.

14
first drive features
FM/AM/HD Radio®/SiriusXM* Satellite Radio (SXM) (if so equipped)
01 AUDIO BUTTON
Press to display the AUDIO screen on the lower display.
02 VOLUME CONTROL DIAL/
(POWER) BUTTON
Turn the VOL/
dial right or left to increase or decrease the volume. Press the
button to
turn the system on or off.
03 SEEK•CAT/TRACK BUTTON
To scan quickly through each broadcasting station, press the SEEK•CAT/TRACK button to
stop at the previous or next broadcast station.
For SiriusXM Satellite Radio, press the SEEK•CAT/ TRACK button to switch to the first
channel of the previous or next category.
For HD Radio®, press the SEEK•CAT/ TRACK button to change the station.
Press the SEEK•CAT/TRACK button to change tracks on a CD.
Press and hold the SEEK•CAT/TRACK button to fast forward or rewind a track on a CD.04 TUNE•CH/FOLDER BUTTON
To manually tune the radio, press the TUNE•CH/FOLDER button left or right.
Press and hold the TUNE•CH/FOLDER button left or right to accelerate radio tuning.05 RADIO BUTTON
Press to change audio source in the order of AM, FM, and SXM (SiriusXM).
06 DISC•AUX BUTTON
Press to change audio source (CD, iPod®, USB, Bluetooth® Streaming Audio or AUX).
07 STATION PRESET KEYS
Up to 36 stations/channels can be set for AM, FM and SXM (SiriusXM).
To store a station in a preset, you must first select a radio band by pr\
essing the RADIO
button, then tune to the desired AM, FM, or SXM station.
Now select and hold the desired station memory key ( 1-36) until the preset number is
updated on the display and a beep is heard. Programming is now complete.\
To retrieve a previously set station, arrow right or left 08 and touch the memory key (1-36)
that contains the stored station/channel you wish to listen to.
*SiriusXM Satellite Radio is only available on vehicles equipped with op\
tional SiriusXM Satellite Radio subscription service.
For more information, refer to the “Audio System (section 4)” of your InTouch Owner’s Manual.
01
02
07
03
08
050604
08