Page 287 of 365

286
uuMaintenance Under the Hood uTransmission Fluid
Maintenance
Transmission Fluid
Check the fluid level when the engine  is at normal operating temperature.
1. Park on level ground, and start the engine.
2. Wait until the radiator fan starts and then 
turn off the engine.
u Perform step 3 after waiting for about 60 
seconds (less than 90 seconds).
3. Remove the dipstick (y ellow loop) from the 
transmission and wipe it with a clean cloth.
4. Insert the dipstick all the way back into the 
transmission securely, as shown in the 
image.
5. Remove the dipstick and check the fluid 
level.
u It should be between the upper and 
lower marks in the  HOT range.
6. If the level is below the lower mark, add 
fluid into the dipstick hole to bring it to the 
level between the upper and lower marks, 
and have your vehicle checked by a dealer 
immediately.
■Automatic Transmission Fluid
Specified fluid: Honda ATF DW-1  (automatic transmission fluid)
1Automatic Transmission Fluid
NOTICE
Do not mix Honda ATF DW-1 with other 
transmission fluids.
Using a transmission flui d other than Honda ATF 
DW-1 may adversely af fect the operation and 
durability of your vehicle' s transmission, and damage 
the transmission.
Any damage caused by usi ng a transmission fluid that 
is not equivalent to Honda ATF DW-1 is not covered 
by Honda's new  vehicle warranty.
NOTICE
Pour the fluid slowly and ca refully so you do not spill 
any. Clean up any spills immediately; they can 
damage components in the engine compartment.Upper Mark
Lower Mark
HOT
 
Range
14 CR-V-31T0A6200.book  286 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 289 of 365
288
uuMaintenance Under the Hood uRefilling Window Washer Fluid
Maintenance
Refilling Window  Washer Fluid
Check the amount of window washer fluid by looking at the reservoir.
If the level is low, fill the washer reservoir.
If the washer fluid is low, the  washer level indicator comes on.
Pour the washer fluid carefully.  Do not overflow the reservoir.1Refilling Window Washer Fluid
NOTICE
Do not use engine antifreeze or a vinegar/water 
solution in the windshield washer reservoir.
Antifreeze can damage y our vehicle's paint. A 
vinegar/water solution ca n damage the windshield 
washer pump.
Canadian models
14 CR-V-31T0A6200.book  288 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 317 of 365

316
uuCleaning uExterior Care
Maintenance
Exterior Care
Dust off the vehicle body after you drive.
Regularly inspect your vehi cle for scratches on painted  surfaces. A scratch on a 
painted surface can result in body rust. If  you find a scratch, promptly repair it.
Wash the vehicle regularly. Wash more  frequently when driving in the following 
conditions:
• If driving on roads with road salt.
• If driving in coastal areas.
• If tar, soot, bird droppings, insects, or  tree sap are stuck to painted surfaces.
• Remove the audio antenna.
2 Audio Antenna  P. 152
•Fold in the door mirrors.
Make sure to follow the  instructions indicated on the automated car wash.
• Keep sufficient distance  between the cleaning nozzl e and the vehicle body.
• Take particular care around the windows. St anding too close may cause water to 
enter the vehicle interior.
• Do not spray high pressure  water directly into the engine compartment. Instead, 
use low pressure water and a mild detergent.
■Washing the Vehicle
■Using an Automated Car Wash
■Using High Pressure Cleaners
1 Washing the Vehicle
Do not spray water into the  air intake vents or engine 
compartment. It can cause a malfunction.
Air Intake Vents
14 CR-V-31T0A6200.book  316 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 318 of 365

317
uuCleaning uExterior Care
Maintenance
A good coat of automotive body wax helps protect your vehicle’s paint from the 
elements. Wax will wear off over time  and expose your vehicle’s paint to the 
elements, so reapply as necessary.
If you get gasoline, oil, engine coolant, or battery fluid on resi n coated parts, they 
may be stained or the coating may peel. Prom ptly wipe it away using a soft cloth and 
clean water.
Wipe using a glass cleaner.
Aluminum is susceptible to deterioration caused by salt and other road 
contaminants. Use a sponge and mild detergent to wipe away promptly.
Be careful not to use harsh chemicals (including some commercial wheel cleaners) or 
a stiff brush. They can damage the clear  coat of the aluminum alloy wheels that 
helps keep the aluminum from  corroding and tarnishing.
■Applying Wax
■Maintaining the Bumpers and Other Resin Coated Parts
■Cleaning the Window
■Maintaining Aluminum Wheels*
1Applying Wax
NOTICE
Chemical solvents and st rong cleaners can damage 
the paint, metal, and plasti c on your vehicle. Wipe 
away spills immediately.
1 Maintaining the Bumpers an d Other Resin Coated Parts
Ask a dealer about the corr ect coating material when 
you want to repair the painted surface of the parts 
made of resin.
1 Cleaning the Window
Wires are mounted to the in side of the rear window. 
Wipe along the same direct ion as the wires with a 
soft cloth so as not to damage them.
* Not available on all models
14 CR-V-31T0A6200.book  317 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 320 of 365

319
Handling the Unexpected
This chapter explains how to handle unexpected troubles.
ToolsTypes of Tools .................................. 320
If a Tire Goes Flat Changing a Flat Tire ......................... 321
Engine Does Not Start Checking the Engine ........................ 327
Jump Starting .................................... 328
Shift Lever Does Not Move .............. 330
Overheating How to Handle Overheating ............. 331 Indicator, Coming On/Blinking
If the Low Oil Pressu
re Indicator Comes 
On................................................ 333
If the Charging System Indicator Comes 
On ................................................. 333
If the Malfunction Indicator Lamp Comes  On or Blinks ................................... 334
If the Brake System Indicator Comes On  (Red) .............................................. 335
If the Electric Power Steering (EPS) System  Indicator Comes On ........................... 335 If the Low Tire Pressure/TPMS Indicator 
Comes On or Blinks ....................... 336
Fuses Fuse Locations ................................. 337
Inspecting and Changing Fuses ........ 339
Emergency Towing ........................... 340
When You Cannot Open the Tailgate.. 341
14 CR-V-31T0A6200.book  319 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 325 of 365

uuIf a Tire Goes Flat uChanging a Flat Tire
324
Handling the Unexpected
1. Place the jack under the jacking point 
closest to the tire to be changed.
2. Turn the end bracket cl ockwise as shown in 
the image until the top of the jack contacts 
the jacking point.
u Make sure that the jacking point tab is 
resting in the jack notch.
3. Raise the vehicle, using the jack handle bar 
and the jack handle, until the tire is off the 
ground.
■How to Set Up the Jack1How to Set Up the Jack
Do not use the jack with  people or luggage in the 
vehicle.
Use the jack provided in your vehicle.
Other jacks may not support  the weight (“load”) or 
may not fit in the jacking point.
The following instructions must be followed to use 
the jack safely:
•Do not use while the engine is running.
•Use only where the ground is firm and level.
•Use only at the jacking points.•Do not get in the vehicl e while using the jack.
•Do not put anything on top of or underneath the 
jack.
3WARNING
The vehicle can easily roll off the jack, 
seriously injuring anyone underneath.
Follow the directions for changing a tire 
exactly, and never get under the vehicle 
when it is supported only by the jack.
Jack 
Handle 
Bar Wheel Nut
 Wrench as Jack Handle
14 CR-V-31T0A6200.book  324 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 328 of 365

327
Handling the Unexpected
Engine Does Not Start
Checking the Engine
If the engine does not start, check the starter.
Starter conditionChecklist
Starter doesn’t turn or turns 
over slowly.
The battery may be dead. Check 
each of the items on the right and 
respond accordingly.Check the brightness of the interior lights.
Turn on the interior lights and check the brightness.
●If the interior lights are dim or do not come on at all
2Battery  P. 309●If the interior lights come on normally 2 Inspecting and Changing Fuses  P. 339
The starter turns over normally 
but the engine doesn’t start.
There may be a problem with the 
fuse. Check each of the items on 
the right and respond accordingly.Review the engine start procedure.
Follow its instructions, and try to start the engine again. 
2 Starting the Engine  P. 239
Check the immobilize r system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2 Immobilizer System P. 106
Check the fuel level.
There should be enough fuel in the tank. 
2 Fuel Gauge P. 77
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
2 Inspecting and Changing Fuses P. 339
If the problem continues:
2Emergency Towing  P. 340
1Checking the Engine
If you must start the vehi cle immediately, use an 
assisting vehicle to jump start it.
2 Jump Starting  P. 328
14 CR-V-31T0A6200.book  327 ページ  2014年2月10日 月曜日 午後7時1分 
         
        
        
     
        
        Page 329 of 365

328
Handling the Unexpected
Jump Starting
Turn off the power to electric devices, such as audio and lights. Turn off the engine, 
then open the hood. 1.Connect the first jump er cable to your 
vehicle's  + terminal.
2. Connect the other end of the first jumper 
cable to the booster battery  + terminal.
u Use a 12 volt booster battery only.
3. Connect the second jumper cable to the 
booster battery  - terminal.
4. Connect the other end of the second 
jumper cable to the engine mounting bolt 
as shown. Do not conn ect this jumper cable 
to any other part.
5. If your vehicle is connected to another 
vehicle, start the assisting vehicle's engine 
and increase its rpm slightly.
6. Attempt to start your vehicle's engine. If it 
turns over slowly, check that the jumper 
cables have good metal-to-metal contact.
■Jump Starting Procedure1Jump Starting
Securely attach the jumper cables clips so that they 
do not come off when the e ngine vibrates. Also be 
careful not to tangle the ju mper cables or allow the 
cable ends to touch each other while attaching or 
detaching the jumper cables.
Battery performance degrades  in cold conditions and 
may prevent the engi ne from starting.
3WARNING
A battery can explode if you do not follow 
the correct procedure, seriously injuring 
anyone nearby.
Keep all sparks, open flames, and smoking 
materials away from the battery.
Booster Battery
14 CR-V-31T0A6200.book  328 ページ  2014年2月10日 月曜日 午後7時1分