2014 FORD MUSTANG ground clearance

Introduction
3
Welcome 3
Shelby® GT500® Unique Features
5
Safety Belts
11
Driving your Shelby® GT500®
12
Breaking-in your vehicle 12
Transmission operation 12
Clutch protection 13
Virtual gauges 15
Track Apps 16
AdvanceTrac® 16
Brakes 20
Launch control 20
Electronically selectable dampers 22
Engine over-rev 23
Ground clearance 24
Driving through water 25
Washing your vehicle 25
Wheels and Tires
26
Wheels 26
Wheel lug nut torque 26
Tire information 27
Roadside Emergencies
30
Wrecker towing 30
Maintenance
35
Engine oil 36
Air filter(s) 41
Table of Contents
1
2014 05+ Mustang(197)
Supplement, 1st Printing, December 2012
USA(fus)

GROUND CLEARANCE
Your vehicle is designed for high speed capability and has been
aerodynamically tuned to reach 200 mph (322 km/h) when properly
equipped. Some of the aerodynamic tuning has been achieved with the
lower front air dam, which is attached below the front splitter. The lower
front air dam is removable with basic tools to suit your driving
conditions, especially if they include steep driveway angles, rough roads,
high curbs or harsh climates.
Since ground clearance is reduced, use caution when approaching curbs
or curb stops from the front and rear as vehicle damage will occur.
Additionally, when crossing speed bumps or driveway curbs, SVT
recommends approaching at a 45 degree angle to reduce the risk of
vehicle damage.
The Shelby GT500 carries the same warranty as other Ford Mustang
models. Damage caused by accidents, collision or objects striking the
vehicle (including driving through a car wash) or misuse of the vehicle,
such as driving over curbs, overloading, racing or using the vehicle as a
permanent stationary power source is not covered under the new vehicle
limited warranty. See the Warranty Guide for complete information.
Driving your Shelby® GT500®
24
2014 05+ Mustang(197)
Supplement, 1st Printing, December 2012
USA(fus)

DRIVING YOUR SHELBY GT500 THROUGH WATER
The Ford Shelby GT500 has aerodynamic devices attached to the
underbody designed to help control airflow for superior performance.
Therefore, the driver must be especially careful to avoid driving through
deep or standing water. If driving through deep or standing water is
unavoidable, do not exceed 10 mph (16 km/h). Never drive through
water that is higher than the bottom of the wheel rims. Water may enter
through the air intake due to the vacuum generated in the engine.
Damage caused by the intake of water in the engine is not covered by
the warranty.
WASHING YOUR SHELBY GT500
Do not drive your vehicle through an automated, commercial car wash
due to the vehicle’s low ground clearance, tire width and track. Wash
your vehicle by hand, or by using a touchless commercial wash with no
mechanical tracks on the floor. Do not use a power washer or high
pressure wand on the striped surfaces or stripe edges. See theOwner’s
Manualfor information on cleaning products and vehicle care.
To maintain proper cooling and aerodynamics at high speeds, your
vehicle has heat exchangers integrated with the front fascia designed to
maximize performance.
Note:Do not use a power washer or high powered spray nozzle as
damage to the fins could occur.
Note:For heavy accumulation of debris or dirt, clean with a non-metallic
soft bristle car wash brush and warm soapy water as needed.
Driving your Shelby® GT500®
25
2014 05+ Mustang(197)
Supplement, 1st Printing, December 2012
USA(fus)

WHEELS
Your SVT vehicle is equipped with unique wheels matched to the tires.
These wheels are more susceptible to damage due to their diameter,
width and low profile tires. To avoid damage to your wheels:
•Maintain proper tire pressure (seeTiresin this supplement).
•Do not drive your vehicle through an automated, commercial car wash
due to the vehicle’s low ground clearance, tire width and track. Wash
your vehicle by hand, or by using a touchless commercial wash with
no mechanical tracks on the floor. Do not use a commercial or high
pressure wand on the striped surfaces.
•When installing wheels, always torque lug nuts to specification with a
torque wrench.
•Inspect your wheels for damage on a regular basis. If a wheel is
damaged, replace it immediately.
•In the event that you encounter an abnormally harsh impact, inspect
the outer diameter of your wheels, both inside and out, for damage.
Wheel Lug Nut Torque Specifications
WARNING:When a wheel is installed, always remove any
corrosion, dirt or foreign materials present on the mounting
surfaces of the wheel or the surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Make sure that any fasteners that
attach the rotor to the hub are secured so they do not interfere with
the mounting surfaces of the wheel. Installing wheels without correct
metal-to-metal contact at the wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to come off while the vehicle is in
motion, resulting in loss of control.
Retighten the lug nuts to the specified torque at 500 miles (800 km)
after any wheel disturbance (tire rotation, changing a flat tire, wheel
removal, etc.).
Bolt size Wheel lug nut torque*
ft-lb N•m
12x 20 100 135
* Torque specifications are for nut and bolt threads free of dirt and
rust. Use only Ford recommended replacement fasteners.
Wheels and Tires
26
2014 05+ Mustang(197)
Supplement, 1st Printing, December 2012
USA(fus)