2014 FIAT PUNTO bulb

129
SAFETYSTARTING
AND DRIVINGIN AN
EMERGENCYSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESWARNING
LIGHTS AND
MESSAGES
GENERIC WARNING
(amber)
The warning light turns on in the follow-
ing circumstances:
Engine oil pressure sensor fault
The warning light turns on when a failure
is detected in the engine oil pressure sen-
sor. Go to a Fiat Dealership to have the
fault fixed as soon as possible.
Start&Stop fault
(for versions/markets where provided)
The warning light comes on when a
Start&Stop failure is detected.
A specific message is displayed on certain
versions.
Exterior lights fault
See the section on warning light
6
.
Fuel cut-off switch tripped
The warning light comes on when the
fuel cut-off switch is triggered.
The display will show a specific message.
è
EXTERIOR LIGHTS
FAULT (amber)
The warning light comes on (on some ver-
sions) when a failure is detected in one
of the following lights:
– sidelights
– brake lights
– rear fog lights
– direction indicators
– number plate lights
– daytime running lights (DRL) (for ver-
sions/markets, where provided)
The failure relating to these lights could
be: one or more blown bulbs, a blown
protection fuse or a break in the electri-
cal connection.
On certain versions warning light èturns
on as an alternative.
A specific message is displayed on certain
versions.
W
REAR FOG LIGHTS
(amber)
The light comes on when the rear fog
lights are turned on.
4
CAR PROTECTION
SYSTEM FAULT
- FIAT CODE
(amber)
The warning light switching on (on some
versions, with the displaying of a message)
signals the failure of the Fiat Code system
or, if installed, of the alarm system: in this
case, contact a Fiat Dealership as soon as
possible.
Y
121-132 PUNTO POP 1ed EN 29/08/13 15.03 Pagina 129

133
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
STARTING THE ENGINE ................................................. 134
CHANGING A TYRE ......................................................... 135
QUICK TYRE REPAIR KIT FIX&GO AUTOMATIC ... 140
CHANGING A BULB ......................................................... 145
CHANGING AN EXTERIOR BULB ................................ 147
CHANGING AN INTERIOR BULB ................................ 152
CHANGING A FUSE .......................................................... 153
RECHARGING THE BATTERY ....................................... 161
RAISING THE CAR ............................................................. 162
TOWING THE CAR ........................................................... 163
I I
N N

A A
N N

E E
M M
E E
R R
G G
E E
N N
C C
Y Y
In an emergency we recommend that you call the toll-free number found in the Warranty Booklet.
You can also go to the www.fiat.com website to find your nearest Fiat Dealership.
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 133

145
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
CHANGING A BULB GENERAL INSTRUCTIONS❒
When a light is not working, check that
the corresponding fuse is intact before
changing the bulb. For the location of
fuses, refer to the “Changing a fuse”
paragraph in this section;
❒
before changing a bulb check the con-
tacts for rusting;
❒
burnt bulbs must be replaced by others
of the same type and wattage;
❒
for safety reasons, always check the di-
rection of the headlight beam after
changing a bulb.
IMPORTANT The internal surface of the
light may appear slightly misty: this does
not indicate a fault, and is actually caused
by low temperature and the degree of hu-
midity in the air. Misting will rapidly dis-
appear when the headlights are switched
on. The presence of drops inside the head-
lights indicates infiltration of water. Go to
a Fiat Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your
car:
AGlass bulbs: clipped into position. Pull
to remove.BBayonet-type bulbs: to remove from
its holder, press the bulb in and turn
it anti-clockwise.
CTubular bulbs: release them from
their contacts to remove.
D-EHalogen bulbs: to remove the bulb,
release the clip holding the bulb in
place. Halogen bulbs must be han-
dled holding the metallic part
only. Touching the transpar-
ent part of the bulb with your
fingers may reduce the intensity of the
light emitted and even compromise the
longevity of the bulb itself. In the event
of accidental contact, wipe the bulb
with an alcohol-soaked cloth and leave
to dry.
Modifications or repairs to
the electrical system (ECUs)
that are not carried out properly or
do not take the system’s technical
specifications into account can cause
malfunctions leading to the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which may cause
small fragments of glass to be pro-
jected outwards if the bulb is broken.
WARNING
fig. 15
F0M0207m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 145

146SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Bulbs Figure ref. Type PowerMain beams/Dipped beams Daylight lightsFront sidelights Front fog lights (for versions/markets, where provided)Front direction indicators Side direction indicators Rear direction indicators Tailights Brake lights Third brake light Reverse lights Rear fog lights Number plate lights Front ceiling light with movable lens
Front ceiling light with spot lights
H4
W21W
W5W
H11
PY21W
WY5W
PY21W
LED
P21W
W2,3W
W16W
W16W
W5W
C10W
C10W D
A
A
–
B
A
B
–
B
B
–
–
A
C
C55 W/60 W
21W
5W
55W
21W
5W
21W
–
21W
2,3W
16W
16W
5W
10W
10W
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 146

147
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
CHANGING AN
EXTERIOR BULBFor the type of bulb and relative power
rating, see “Changing a bulb”.
FRONT LIGHT CLUSTERS
fig. 16
The front light clusters contain sidelights,
dipped beam, main beam and direction in-
dicator bulbs.
The bulbs are arranged inside the light
cluster as follows:
Asidelights
Bdaytime running lights
Cdirection indicators
Dmain beam/dipped beam headlights.
IMPORTANT You can replace the front
direction indicator, main beam and dipped
beam headlight bulbs through the access
flap (see “Direction indicators” in this sec-
tion).SIDELIGHTS fig. 17
To change the bulb, proceed as follows:
❒
remove the rubber cap by pulling the
flap;
❒
press in tabs Band remove the bulb
holder;
❒
remove the bulb C and replace it;
❒
refit the bulb holder and then refit the
cap, ensuring that it locks into place.
fig. 16
F0M0630m
fig. 17
F0M0631m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 147

148SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
DAYTIME RUNNING LIGHTS
(DRL)
To change the bulb, proceed as follows:❒
turn the bulb holder A-fig. 18anti-
clockwise using the tab and pull it out;
❒
remove the bulb Bby pushing it in
slightly and turning it anti-clockwise;
❒
refit the bulb holder by putting it in its
housing and turning it clockwise until it
locks into place.MAIN/DIPPED BEAM
HEADLIGHTS fig. 19
To change the bulb, proceed as follows:
❒
remove the rubber cap;
❒
disconnect the central electric connec-
tor B-fig. 19and release the bulb hold-
er catch;
❒
remove the bulb Aand replace it;
❒
fit the new bulb, aligning the outlines of
the metallic part with the grooves on
the reflector;
❒
refit the bulb holder catch and recon-
nect the electrical connector;
❒
refit the cap, ensuring that it locks in-
to place.DIRECTION INDICATORS
Front fig. 20
To change the bulb, proceed as follows:
❒
steer the right/left wheel inwards;
❒
turn the catch A-fig. 20, then lift off the
access lid B;
fig. 18
F0M0632m
fig. 19/b
F0M0634m
fig. 19/a
F0M0633m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 148

149
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
remove the bulb holder cover C-
fig. 21by turning it anti-clockwise;
❒
remove the bulb D-fig. 22by pushing
it in gently and turning anti-clockwise
(“bayonet” clamping), then replace it;
❒
refit the bulb holder cover C-fig. 21by
turning it clockwise and locking it prop-
erly;
❒
close the lid B-fig. 20then tighten the
catch A.Side fig. 23
To change the bulb, proceed as follows:
❒
slide the lens Atowards the front of
the car to press in the internal catch B,
then pull the unit outwards;
❒
turn the bulb holder Canti-clockwise,
extract bulb Dand replace it;
❒
refit the bulb holder Cinto the lens by
turning it clockwise;
❒
refit the unit making sure the internal
catch Bclicks into place.FRONT FOG LIGHTS
(for versions/markets where provided)
To replace the bulb:❒
loosen the screw A-fig. 24and re-
move the protection template B;
❒
loosen the fixing screwsCand re-
move the headlamp;
fig. 20
F0M0635m
fig. 21
F0M0636m
fig. 24
F0M0638m
fig. 23
F0M0637m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 149

150SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
remove the bulb A-fig. 25by ro-
tating it counter-clockwise and dis-
connect the electrical connector.
REAR LIGHT CLUSTERS
The rear light clusters contain taillight,
brake light and direction indicator bulbs.
The bulbs are arranged inside the light
cluster fig. 26as follows:
Ddirection indicators
Ebrake lights.
To change the bulb proceed as follows:❒
undo both fastening bolts A-fig 26;
❒
disconnect the central electric connec-
tor Band pull the lens unit outwards;
❒
unhook the bulb holder by unclipping
the fasteners C-fig. 27;
❒
remove the bulb by pushing it in gen-
tly and turning anti-clockwise (“bayo-
net” clamping), then replace it;
❒
refit the bulb holder;
❒
reconnect the electric connector, cor-
rectly realign the unit with the car body
and then tighten the fastening screws
A.IMPORTANT To replace the LED tail-
lights you must contact a Fiat Dealership.
fig. 25
A
F0M0639m
fig. 26
F0M0640m
fig. 27
F0M0641m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 150