2014 FIAT PANDA key

Request for additional remote controls
The system can recognise up to 8 keys with
incorporated remote control. Should a new remote
control be necessary, go to a Fiat Dealership, taking
an ID document and the car ownership documents.
Changing battery - key with remote control
To replace the battery, proceed as follows:
❒press button A fig. 11 and open the metal insert B;
❒turn screw C to
using a fine bit screwdriver;
❒take out the battery case D and replace the
battery E making sure that polarities are correct;
❒refit the battery case D inside the key and lock it
by turning screw C to
.
Used batteries must be disposed of, as
specified by law, in the special containers.
Otherwise take them to a Fiat Dealership,
which will deal with their disposal.
fig. 11
F0W0189
21GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IGNITION DEVICEThe key can be turned to 3 different positionsfig. 12:
❒STOP: engine off, key can be removed, steering
column locked. Some electrical devices (e.g. sound
system, central door locking system, etc.) can
operate;
❒MAR-ON: driving position. All electrical devices
are enabled;
❒AVV: engine start-up.
The ignition switch is fitted with a safety system that
requires the ignition key to be turned back to STOP
if the engine does not start, before the starting
operation can be repeated.
WARNING
If the ignition device has been tampered
with (e.g. an attempted theft), have it
checked over by a Fiat Dealership before driving
again.
WARNING
Always remove the key when you leave
your car to prevent someone from
accidentally operating the controls. Remember
to engage the handbrake. Engage 1
st
gear if
the car is parked uphill or reverse if the car is
parked downhill. Never leave children
unattended in the car.
STEERING LOCK
Engagement:when the key is in position STOP,
remove the key and turn the steering wheel until it is
locked.
Disengagement:move the steering wheel slightly
as you turn the ignition key to MAR-ON.
1
02
fig. 12
F0W0102
22GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

WARNING
It is absolutely forbidden to carr y out
any after-market operation involving
steering system or steering column
modifications (e.g.: installation of anti-theft
device) that could badly affect performance and
safety, invalidate the warranty and also result
in non-compliance of the car with type-
approval requirements.
WARNING
Never remove the key while the car is
moving.The steering wheel will lock
as soon as it is turned.This holds true for cars
being towed as well.
SEATS
WARNING
All adjustments must be made with the
car stationary.
WARNING
If a side bag is fitted, it is dangerous to
use seat covers not available from
Lineaccessori Fiat .
FRONT SEATS
Lengthwise adjustment
Lift lever A fig. 13 and push the seat forwards or
backwards: in driving position your arms should rest
on the rim of the steering wheel.
WARNING
Once you have released the adjustment
lever, always check that the seat is
locked on the guides by trying to move it back
and for th. If the seat is not locked into place,
it may unexpectedly slide and cause the driver
to lose control of the car.
23GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Document holder pocket(for versions/markets
where provided)
On some versions the multifunction pocket can be
removed from the seat backrest, using the two
pullers of the zips in the pocket bottom fig. 16.
The removed pocket can be folded and closed with
the buttons at its ends.
WARNING
If passengers are seating in the rear
seats, remove all potentially dangerous
objects which may cause injuries in case of
accident .Electric front seat heating(for versions/markets,
where provided)
To heat the cushion of the front seats, with the
ignition key in MAR-ON, press respectively button A
or B fig. 17.
To deactivate the function press the button again.
fig. 16
F0W0302
fig. 17
F0W0300
25GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REAR VIEW MIRRORSREAR VIEW MIRROR
The mirror is fitted with a safety device that causes
its release in the event of a violent impact with
the passenger. Operate lever A fig. 22 to adjust the
mirror into two different positions: normal or
anti-glare.
DOOR MIRRORS
Manual adjustment
From the inside of the car, operate lever A fig. 23 to
adjust the mirror.Electrical adjustment(for versions/markets,
where provided)
The mirrors can be adjusted only if the ignition key is
in MAR position.
fig. 22
F0W0054
fig. 23
F0W0053
29GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

EXTERIOR LIGHTSThe left stalk operates most of the exterior lights.
The ignition key has to be in the MAR position
for the exterior lights to come on.
The instrument panel and the various dashboard
controls will come on with the exterior lights.
SIDE LIGHTS/DAYTIME RUNNING LIGHTS
(DRL)
"Daytime Running Lights"
(for versions/markets, where provided)
With the ignition key turned to MAR and ring nut A
fig. 31 turned to positionOthe daytime running
lights are automatically activated; the other lights and
interior lighting remain off.
WARNING
The daytime running lights are an
alternative to the dipped beam
headlights for driving during the daytime in
countries where it is compulsory to have lights
on during the day, and they are also permitted
in those countries where this not obligator y.
WARNING
Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels.The use of daytime
running lights is governed by the highway code
of the country in which you are driving. Comply
with legal requirements.
SIDE LIGHTS AND DIPPED BEAM
HEADLIGHTS
With the ignition key turned to MAR, turn the ring
nut A fig. 31 to
. If dipped beams are activated,
the daytime running lights go out and the side lights
and dipped headlights come on. The
warning
light will come on in the instrument panel.
When the ignition key is turned to STOP or
removed and the ring nut is turned from O to
, all
the side lights and number plate lights switch on.
The
warning light will come on in the
instrument panel.
fig. 31
F0W0127
45GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

PARKING LIGHTS
These lights can only be turned on with ignition key
in STOP position or removed, by moving the ring nut
A first to positionOand then to position
.
The warning light
switches on on the instrument
panel.
MAIN BEAM HEADLIGHTS
To activate the main beam headlights, with ring nut at
, pull the stalk towards the steering wheel. The
warning light
switches on in the instrument panel.
When the stalk is pulled towards the steering wheel
again, the lights deactivate, the dipped headlights
reactivate and the
warning light switches off.
FLASHING
You can flash the headlights by pulling the stalk
towards the wheel (unstable position). The
warning light will come on in the instrument
panel.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
upwards:right direction indicator activation;
downwards:left direction indicator activation.
Warning light
or
will flash in the instrument
panel. The indicators switch off automatically when
the steering wheel is straightened.Lane change function
If you wish to signal a lane change, place the left stalk
in the unstable position for less than half a second.
The direction indicator on the side selected will flash
five times and then switch off automatically.
“FOLLOW ME HOME” DEVICE
This allows the space in front of the car to be lit up
for a certain period of time.
Activation:with the ignition key on STOP or
removed, pull the stalk towards the steering wheel
within 2 minutes from when the engine is turned off.
At each single movement of the stalk, the lights
will remain on for an extra 30 seconds up to a
maximum of 210 seconds; then the lights are
switched off automatically.
Each time the stalk is operated, the
warning light
on the instrument panel switches on and the display
also shows a message and how long the function
will remain active.
The
warning light switches on when the stalk is
first moved and stays on until the function is
automatically deactivated. Each time the stalk is
activated it increases the time that the lights remain
on.
Deactivation:keep the stalk pulled towards the
steering wheel for more than two seconds.
46GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

WINDOW CLEANINGThe right stalk controls windscreen wiper/washer
and rear window wiper/washer operation.
WINDSCREEN WASHER/WIPER
It can be operated only with the ignition key turned
to MAR-ON.
The ring nut A fig. 32 can be moved to four different
positions:
windscreen wiper off.intermittent operation.continuous slow operation.continuous fast operation.
Move the stalk upwards (unstable position) to limit
operation to the time for which the stalk is held
in this position.When released, the stalk will return to its default
position and the wiper will be automatically stopped.
With the ring nut A fig. 32 in position
, the
windscreen wiper will automatically adapt operating
speed to the speed of the car.
With the windscreen wiper operational, if reverse
gear is engaged, the rear window wiper is
automatically activated.
Never use the windscreen wiper to remove
layers of snow or ice from the windscreen.
In such conditions, the windscreen wiper
may be subjected to excessive stress and the
overload cut-out , which prevents operation for a
few seconds, may intervene. If operation is not
restored (even after turning the key and
restarting the car engine), contact a Fiat
Dealership.Do not operate the windscreen wiper with
the blades lifted from the windscreen.
"Smart washing" function
Pull the stalk towards the steering wheel (unstable
position) to activate the windscreen washer.
Keeping the stalk pulled for more than half a second,
with just one movement it is possible to operate
the washer jet and the wiper at the same time.
The wiper stops working three strokes after the
stalk is released.
fig. 32
F0W0126
47GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX