2014 Citroen DS5 wheel

Tr i p c o m p u t e r


System that gives you information on the journey in progress (range, fuel consumption…).




When the trip required is displayed, press
the control for more than two seconds
or use the left hand thumb wheel of the
steering mounted controls.
Trips "1"
and "2"
are independent but their use
is identical.
For example, trip "1"
can be used for daily
figures, and trip "2"
for monthly figures.











Instrument panel screen

Information display





Press the button on the end of the wiper
control stalk
to display the various tabs in
succession.



- The current information tab with:


●
the range,

●
the current fuel consumption,

●
the Stop & Start time counter.





- Tr i p "1"
with:


●
the average speed,
for the first trip.

●
the average fuel consumption.





- Tr i p "2"
with:


●
the average speed,
for the second trip.

●
the average fuel consumption.




Tr i p r e s e t




- Radio or media.

- Satellite navigation.

OFF

Locking the vehicle
with exterior perimeter
monitoring only
Deactivate the interior volumetric and anti-lift
monitoring to avoid unwanted triggering of the
alarm in certain cases such as:


- leaving a window partially open,

- washing your vehicle,

- changing a wheel,

- having your vehicle towed,

- transpor tation by sea.

Deactivation of the interior
volumetric and anti-tilt monitoring



Switch of the ignition and within
ten seconds, press this button
until the indicator lamp is on
continuously.


Get out of the vehicle.


Press the locking button on
the remote control immediately
or lock the vehicle using the
Keyless Entry and Starting
system.
The exterior perimeter monitoring alone is
activated: the indicator lamp in the button
flashes once per second.
To be effective, this deactivation must be
carried out each time the ignition is switched
off.
Where the vehicle locks itself again
automatically (occurs 30 seconds after
unlocking, if a door or the boot is not
opened), the monitoring system is not
reactivated automatically.
To reactivate it, the vehicle must be
unlocked and locked again, using the
remote control or the "Keyless Entry
and Starting" system.

Front seats


Manual



1.
Adjustments to the height and angle
of
the head restraint

To raise it, pull upwards.
To lower it, press on the lug and the head
restraint at the same time.

2.
Adjustment of the backrest angle

Turn the wheel to adjust the angle of the
backrest.

3.
Adjustment of the seat height

Raise or lower the control lever the number
of times required to obtain the desired
position.

4.
For wards-backwards adjustment of the
seat position

Lift the control bar and slide the seat
for wards or backwards.

5.
Adjustment of the driver's lumbar
support

Turn the wheel to obtain the desired level
of lumbar support.


Before moving the seat backwards, ensure that there is nothing that might prevent the full
travel of the seat, so as to avoid the risk of of jamming the seat caused by the presence of
objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement
immediately.

Massage function







This system provides a back massage. It only
operates when the engine is running or in
STOP mode of the Stop & Start system.


Activation




Press this switch.


Its indicator lamp comes on and the massage
function is activated for a period of 1 hour.
During this time, massage is per formed in
6 cycles of 10 minutes (6 minutes of massage
followed by 4 minutes break).
After one hour, the function is deactivated, the
indicator lamp goes off.


Deactivation

You can deactivate the massage
function at any time by pressing this
switch, its indicator lamp goes off.









Heated seats control





Use the adjustment wheel to switch on and
select the level of heating required:



0

:
Off.

1

:
Low.

2

:
Medium.

3

:
High.










With the engine running, the front seats can be
heated separately.

87Comfort







Automatic day/night model

By means of a sensor, which measures the
light from the rear of the vehicle, this system
automatically and progressively changes
between the day and night uses. Adjustable mirror providing a central rear ward
view.
Equipped with an anti-dazzle system, which
darkens the mirror glass and reduces the
nuisance to the driver caused by the sun,
headlamps from other vehicles...





Rear view mirror


In order to ensure optimum visibility
during your manoeuvres, the mirror
lightens automatically when reverse
gear is engaged.










Steering wheel adjustment





When stationary
, pull the control lever to
release the adjustment mechanism.


Adjust the height and reach to suit your
driving position.


Push the control lever to lock the
adjustment mechanism.
As a safety precaution, these
operations should only be carried out
while the vehicle is stationary.
As a safety measure, the mirrors should
be adjusted to reduce the "blind spot".







Seeing clearly

For better rear vision, align the bottom of the
rear view mirror with the bottom of the rear
screen.

Starting-switching off the engine




Insert the electronic key in the reader.


Press the brake pedal for vehicles with
an automatic or electronic gearbox, or
fully declutch for vehicles with a manual
gearbox.

Starting using
the electronic key
Starting with the "Keyless
Entry and Starting" system

If one of the starting conditions is not
met, a reminder message appears in
the instrument panel screen. In some
circumstances, it is necessary to turn
the steering wheel slightly while pressing
the "START/STOP" button to assist
unlocking of the steering; a message
warns you when this is needed.
With a manual gearbox
, put the gear lever in neutral.
With an electronic gearbox
, put the gear lever in N
.
With an automatic gearbox
, put the gear lever in P
or N
.

For Diesel vehicles
, in
temperatures below zero the
engine will not start until the
preheater warning lamp has gone off.
If this warning lamp comes on after
pressing "START/STOP", you should
hold the brake or clutch pedal down
until the warning lamp goes off and
do not press the START/STOP button
again.



With the electronic key inside the vehicle
(it is not necessary to put it in the reader),
press the brake pedal for vehicles with
an automatic or electronic gearbox, or
fully declutch for vehicles with a manual
gearbox.

Press the " START/STOP
"
button.
The engine starts (see the
warning below for Diesel
vehicles).


Press the " START/STOP
"
button.
The engine starts (see the
warning below for Diesel
vehicles).
The "Keyless Entry and Starting" device
must be in the recognition zone.
For safety reasons, do not leave
this zone with the vehicle running.

With the ignition on or the engine running, to
release the parking brake, press
the brake

pedal
, pull
then release control lever A
.
The full release of the parking brake is
confirmed by:

Manual release



- the braking warning lamp and
the P
warning lamp in the control
lever A
going off,

- display of the message "Parking
brake off ".
If you pull the control lever A
without pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel.
If necessary, you can make a maximum
application
of the parking brake. It is obtained
by means of a long pull
on control lever A
,
until you see the message "Parking brake
applied fully" and an audible signal is heard.

Maximum application is essential:



- in the case of a vehicle towing a caravan
or a trailer, if the automatic functions are
activated but you are applying the parking
brake manually,

- when the slope you are parked on may
vary (e.g. on a ferry, on a lorry, during
towing).



Maximum application


In the case of towing, a loaded vehicle
or parking on a gradient, make a
maximum application of the parking
brake then turn the front wheels
towards the pavement and engage a
gear when you park.
After a maximum application, the
release time will be longer.

Before leaving the vehicle, check that
parking brake warning lamps in the
instrument panel and the control lever A

are on fixed, not flashing.
With the vehicle stationary, to apply the parking
brake whether the engine is running or off, pull

control lever A
.


Manual application

The application of the parking brake is
confirmed by:


- illumination of the braking warning
lamp and of the P
warning lamp in
the control lever A
,

- display of the message "Parking
brake on".
When the driver’s door is opened with the
engine running, there is an audible signal and a
message is displayed if the parking brake has
not been applied, unless the selector lever is
in position P
(Park) in the case of an automatic
gearbox.

Situations



Consequences


To apply the electric parking brake:



immobilise the vehicle and switch off the ignition.


pull the control for at least 5 seconds or until application is complete.


switch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than during normal operation.
To release the electric parking brake:



switch on the ignition.


pull the control lever and hold it for approximately 3 seconds then
release it.
If the braking warning lamp is flashing or if the warning lamps do not
come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a CITROËN dealer or a
qualified workshop.

and possibly
flashing


Display of the message " Parking brake fault
" and of the following
warning lamps:


- Only the automatic application on switching off the engine and
automatic release on acceleration functions are available.

- The manual application/release of the electric parking brake and the
emergency braking are not available.
and possibly



flashing
Display of the message "Battery charge fault".

- You must stop as soon as it is safe to do so. Switch off and
immobilise your vehicle (if necessary, place the a chock under a
wheel).

- Apply the electric parking brake before switching off the engine.