2014 Citroen DS3 fuel

193
DS3_en_Chap10_info-pratiques_ed01-2014
Running out of fuel (Diesel)If your vehicle is fitted with an HDI engine, the fuel system must be primed if you run out of fuel.
T his   system   consists   of   a   priming   pump   and   a   transparent   pipe   under   the   bonnet.
F
 
F
ill   the   fuel   tank   with   at   least   five   litres   of  
D

iesel.
F
 
O
pen   the   bonnet.
F
 
D
epending   on   version,   unclip   the   cover   to  
g

ain   access   to   the   priming   pump.
F
 
S
queeze   and   release   the   priming   pump  
u

ntil   resistance   is   felt   (could   be   from   the  
f

irst application) and fuel appears in the
transparent
  pipe   with   the   green   connector.
F
 
O
perate   the   starter   until   the   engine   starts.
F
 
D
epending   on   version,   put   the   cover   back  
i

n   position   and   clip   it   in   place.
F
 
C
lose   the   bonnet.
BlueHdi 100 engines
F Fill  the   fuel   tank   with   at   least   five   litres   of  D
iesel.
F
 
S
witch   on   the   ignition   (without   starting   the  
e

ngine).
F

W
ait around 6 seconds and switch off the
ignition.
F
 
R
epeat   the   operation   10   times.
F
 
O
perate   the   starter   to   run   the   engine.
If
 
the
 
engine
 
does
 
not
 
start
 
at
 
the
 
first
 
a

ttempt,
 
do
 
not
 
try
 
again.
Operate
 
the
 
priming
 
pump
 
again,
 
then
 
t

he
 
starter.
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
adblue® additive and SCR system
f
or
 
Blue
  HDi   Diesel   engines
To assure respect for the environment and c
onformity   with   the   new   Euro   6   emissions  
s

tandard,   without   adversely   affecting   the  
p

er formance   or   fuel   consumption   of   Diesel  
e

ngines,   CITROËN   has   taken   the   decision   to  
e

quip   its   vehicles   with   an   effective   system   that  
a

ssociates SCR (Selective Catalytic Reduction)
with
  a   particle   filter   (FAP)   for   the   treatment   of  
e

xhaust   gases.
Presentation of the ScR s ystem
Using an additive called AdBlue® containing u
rea, a catalytic converter turns up to
85% of
 
nitrous
 
oxides
 
(NOx)
 
into
  nitrogen  
a

nd
 
water,
 
which
 
are
 
harmless
 
to   health   and  
t

he environment. The
a d
blu
e
® additive is held in a special
tank
 
located
  under   the   boot   at   the   rear   of  
t

he
 
vehicle.
 
It   has   a   capacity   of   17   litres:   this  
p

rovides
 
a
 
driving   range   of   about   12   500   miles  
(

20
 
000
 
km),
  after   which   an   alert   is   triggered  
w

arning
 
you
 
when   the   reserve   remaining   is  
e

nough
 
for
 
just   1   500   miles   (2   400   km).
During
 
each
  scheduled   service   of   your   vehicle  
b

y
 
a
 
CITROËN   dealer   or   a   qualified   workshop,  
t

he
a
d
blu

e
® additive tank is refilled in order to a
llow
 
normal   operation   of   the   SCR   system.
If
 
the
 
estimated   mileage   between   two   services  
i

s
 
greater
 
than   12   500   miles   (20   000   km),   we  
r

ecommend
  that   you   go   to   a   CITROËN   dealer  
o

r
 
a
 
qualified   workshop   to   have   the   necessary  
t

op-up
 
carried   out.
on
ce the a
dbl
ue
® tank is empty, a
 
system
 
required
  by   regulations  
p

revents
 
starting
 
of   the   engine.
If the SCR

is faulty, the level of
emissions
 
from
 
your   vehicle   will   no  
l

onger
 
meet
 
the
 
Euro   6   standard:   you  
v

ehicle
 
becomes
 
polluting.
In
 
the
 
event
 
of
 
a
 
confirmed   fault  
w

ith
 
the
 
SCR
 
system,   you   must   go  
t

o a CITR
oË

N dealer or a qualified
workshop
 
as
 
soon   as   possible:   after  
a

 
running
 
distance   of   650   miles  
(

1 100
 
km),
 
a
 
system   will   be   triggered  
a

utomatically
 
to
 
prevent   engine  
s

tarting.

199
DS3_en_Chap10_info-pratiques_ed01-2014
keep a dblu e® out of the reach of
children,
 
in
 
its
  original   bottle.
Never transfer
a d
blu
e
® to another
container:
 
it
 
would
 
loose   its   purity. Never
  dilute   the   additive   with   water.
Never pour the additive into the Diesel
fuel   tank.
Never   top-up   from   an   AdBlue®
dispenser
 
reserved
 
for
 
heavy
 
goods  
v

ehicles.
Filling
 
the
 
AdBlue
® tank is an operation i
ncluded in every routine service on your
vehicle by a CITR
oË

N dealer or a qualified
workshop.
Nevertheless,
 
given   the   capacity   of   the   tank,  
i

t
 
may
 
be
 
necessary   to   top-up   the   additive  
b

etween
 
services,
  more   particularly   if   an   alert  
(

warning
 
lamps
 
and   a   message)   signals   the  
r

equirement.
You
 
can
 
got
 
to
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop.
If
 
you
 
envisage
 
topping-up   yourself,   please  
r

ead
 
the
 
following
 
warnings   carefully.
Topping-up the AdBlue® additive
Precautions in use
Use only adblu e® additive that meets the I
SO 22241
 
standard.
The
 
supply
 
in
 
a
 
non-drip   bottle   simplifies  
t

oping-up.
 
You
 
can   obtain   1.89   litre   (half   a   US  
g

allon)
 
bottles
 
from   a   CITROËN dealer   or   a  
q

ualified
 w

orkshop.
The
a
dblu
e® additive is an urea-based
solution.
 
This   liquid   is   non-flammable,  
c

olourless
 
and   odourless   (kept   in   a   cool   area).
In
 
the
 
event
 
of   contact   with   the   skin,   wash  
t

he
 
affected
 
area   with   soap   and   water.   In   the  
e

vent
 
of
 
contact   with   the   eyes,   wash   (irrigate)  
t

he
 
eyes
 
with   large   amounts   of   water   or   with  
a

n
 
eye
 
wash
  solution   for   at   least   15   minutes.  
I

f
 
a
 
burning
 
sensation   or   irritation   persists,   get  
m

edical
 
attention.
If
 
swallowed,   immediately   wash   out   the   mouth  
w

ith
 
clean
 
water   and   then   drink   plenty   of   water.
In
 
certain
 
conditions   (high   ambient  
t

emperature,
  for   example),   the   risk   of   release  
o

f
 
ammonia
 
cannot   be   excluded:   do   not   inhale  
t

he
 
product.
 
Ammonia   vapour   has   en   irritant  
e

ffect
 
on
 
mucous   membranes   (eyes,   nose   and  
t

hroat).
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
Fuse table
Fuse N°Rating Functions
F1 20 AEngine
  control   unit   supply,   cooling   fan   unit   control   relay,   multifunction   engine   control   main   relay,   injection   pump  
(

Diesel).
F2 15 AHorn.
F3 10 AFront
  /   rear   screenwash.
F4 20 ALED
  lamps.
F5 15 ADiesel
  heater   (Diesel),   particle   filter   additive   pump   (Diesel),   air   flow   sensor   (Diesel),   blow-by   heater   and  
e

lectrovalves   (VTi).
F6 10 AABS/ESP
  control   unit,   secondary   stop   switch.
F7 10 AElectric
  power   steering,   automatic   gearbox.
F8 25 AStarter
  control.
F9 10 ASwitching
  and   protection   unit   (Diesel).
F10 30 AFuel
  heater   (Diesel),   blow-by   heater   (Diesel),   fuel   pump   (VTi),   injectors   and   ignition   coils   (petrol).
F11 40 AHeater
 b

lower.

229
DS3_en_Chap10_info-pratiques_ed01-2014
Fuse N°Rating Functions
F12 30 AWindscreen
  wipers   slow   /   fast   speed.
F13 40 ABuilt-in
  systems   inter face   supply   (ignition   positive).
F14 30 AValvetronic
  supply   (VTi).
F15 10 ARight-hand
  main   beam   headlamps.
F16 10 ALeft-hand
  main   beam   headlamps.
F17 15 ALeft-hand
  dipped   beam   headlamps.
F18 15 ARight-hand
  dipped   beam   headlamps.
F19 15 AOxygen
  sensors   and   electrovalves   (VTi),   electrovalves  
(

Diesel),   EGR   electrovalve   (Diesel).
F20 10 APumps,
  electronic   thermostat   (VTi),   timimg   electrovalve  
(

THP),   water   in   fuel   sensor   (Diesel).
F21 5 AFan
  assembly   control   supply,   ABS/ESP,   turbo   pump   (THP).
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
Matt paintWe recommend the use of a high pressure jet   wash,   or   at   least   a   water   hose   with   a   high  
o

utput.
We
  recommend   that   the   vehicle   be   rinsed   using  
d

e-ionised
 w
ater.
Use
  only   a   microfibre   cloth   to   dry   the   vehicle.  
I

t   must   be   clean   and   used   without   heavy  
p

ressure.
Lightly
  wipe   off   any   fuel   stains   present   on   the  
b

odywork   using   a   soft   cloth,   then   leave   to   dry.
From
  the   range   of   cleaning   and   maintenance  
p

roducts   in   the   "TECHNATURE"   range  
r

ecommended   and   approved   by   CITROËN,  
u

se   only   the   insect   remover   and   car   shampoo,  
w

hich are the only products to be used on the
bodywork.
The
  insect   remover   can   also   be   used   to   remove  
m

inor   marks   (for   example:   finger   marks...).
al

ways have paint repairs done by a CITR
oË
N
dealer
  or   a   qualified   workshop.
Recommendations
 
on
 
the
 
care
 
and
 
maintenance
 
your
 
vehicle
 
are
 
given
 
in
 
the
 
maintenance
 
and
 
warranty   guide.
Never
 
clean
 
the
 
vehicle
 
without
 
water.
Never wash your vehicle in an
automatic
 
roller
 
brush
 
car
 
wash.
Never polish the vehicle body, nor the
alloy
 
wheels.
 
Doing
 
this
 
will
 
make
 
the
 
pa

intwork
 sh

iny.
Do not use paint cleaners, abrasive
products
 
or
 
paint
 
polishing
 
or
 
p

reserving
 
products
 
(such
 
as
 
wax,
 
f

or
 
example)
 
on
 
the
 
paintwork.
 
These
 
p

roducts
 
are
 
only
 
suitable
 
for
 
bright
 
f

inishes.
 
Application
 
of
 
these
 
products
 
o

n
 
vehicles
 
with
 
a
 
matt
 
finish
 
will
 
s

eriously
 
damage
 
the
 
paint
 
sur face
 
of
 
t

he
 
vehicle,
 
giving
 
rise
 
to
 
irreversible
 
s

hiny
 
or
 
stained
 
areas.
Never
 
use
 
a
 
high
 
pressure
 
jet
 
wash
 
w

ith a lance fitted with a brush, this
may
 
scratch
 
the
 
paintwork.
Never
 
select
 
a
 
wash
 
programme
 
that
 
f

inishes
 
with
 
a
 
hot
 
wax
 
cycle.
Advice on care and maintenance
If you vehicle is finished with a clear matt l acquer,   please   observe   the   following  
r

ecommendations   to   avoid   damaging   the  
p

aintwork   by   the   use   of   an   inappropriate  
c

leaning
 pro
cedures.
These
  recommendations   are   also   valid   for   alloy  
r

oad   wheels   finished   with   clear   matt   lacquer.

DS3_en_Chap11_verifications_ed01-2014
Checks
This section describes access to the engine compartment, the procedure for   bleeding   the   fuel   system   on   Diesel   engines   after   running   out   of   fuel,  
t

he   location   of   various   engine   components   needed   to   check   the   levels  
a

nd   the   main   wearing   parts.

DS3_en_Chap11_verifications_ed01-2014
Diesel engines
1. Screenwash  fluid   reservoir.
2. C oolant   header   tank.
3.
 A

ir   filter.
4.
 B

rake   fluid   reservoir.
5.
 B

attery.
6.
 F

usebox.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.
9.
 P

riming   pump   (on   fuel   filter).