2014 CITROEN DS3 CABRIO ignition

) Uncoil the white pipe G
fully. )
Unscrew the cap from the white pipe.
)
Connect the white pipe to the valve of the
tyre to be repaired.
Repair procedure
Avoid removing any foreign bodieswhich have penetrated into the tyre.
)Connect the compressor's electric plug to
the vehicle's 12 V socket.
)Star t the vehicle and leave the engine running.
)Switch off the ignition.
Take care, this product is harmful(e.g. ethylene-glycol, colophony...) if swallowed and causes irritation to the eyes.Keep this product out of the reach of children.

Do not star t the compressor before connecting the white pipe to the tyre valve: the sealant product would be expelled through the pipe.
)Turn the selector Ato the "sealant"
position.)Check that the switch B
is in position "O".

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must belevel, stable and not slippery. Apply the parking brake, switch off the ignition and engage first gear * to lock the wheels.
If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. It is imperative that you ensure that the occupants get out of the vehicle andwait where they are safe.
Never go underneath a vehicle raised using a jack; use an axle stand.


List of operations
)
Remove the chromed bolt cover from each of the bolts using the tool 3 (alloy wheels
only).)
Fit the socket 4 on the wheelbrace 1to slacken the security bolt (if your vehicle isfitted with them).)
Slacken the other bolts using the
wheelbrace 1only.
* position
P
for an automatic gearbox.

227Practical information
Fuse N°RatingFunctions
F820 AMultifunction screen, audio system, navigation radio, alarmcontrol unit, alarm siren.
F
930 A12 V socket, portable navigation suppor t supply.
F10 15
ASteering wheel controls.
F1
115 AIgnition, diagnostic socket, automatic gearbox control unit.
F1
215 ARain / brightness sensor, trailer relay unit.
F1
35 AMain stop switch, engine relay unit.
F1415 AParking sensors control unit, airbag control unit, instrument panel, digital air conditioning, USB Box, Hi-Fi amplifier.
F15
30 ALocking.
F1
6-Not used.
F1740 ARear screen and door mirrors demisting/defrosting.
S
H-PA RC shunt.

229Practical information

Fuse table
Fuse N°RatingFunctions
F120 A
Engine control unit supply, cooling fan unit control relay, multifunction engine control main relay, injection pump(Diesel).
F
215 A Horn.
F
310 A Front / rear wash-wipe.
F420 A LED lamps.
F5
15 A Diesel heater (Diesel), particle filter additive pump (Diesel), air flow sensor (Diesel), EGR electrovalve (Diesel),
blow-by heater and electrovalves (VTi).
F
610 A ABS/ESP control unit, secondary stop switch.
F
710 A Electric power steering, automatic gearbox.
F8
25 A Starter control.
F
910 A Switching and protection unit (Diesel).
F10 30 A
Fuel heater
(Diesel), blow-by heater (Diesel), fuel pump (VTi), injectors and ignition coils (petrol).
F1140 A Heater blower.

Fuse N°RatingFunctions
F1230 AWindscreen wipers slow / fast speed.
F1
340 ABuilt-in systems inter face supply (ignition positive).
F1
430 AValvetronic supply (VTi).
F1
510 ARight-hand main beam headlamps.
F16 10 ALe
ft-hand main beam headlamps.
F1715 ALeft-hand dipped beam headlamps.
F18 15
ARight-hand dipped beam headlamps.
F1
915 AOxygen sensors and electrovalves (VTi), electrovalves
(Diesel), EGR electrovalve (Diesel).
F20 10 APumps, electronic thermostat
(VTi), timimg electrovalve (THP), water in fuel sensor (Diesel).
F2
15 AFan assembly control supply, ABS/ESP, turbo pump (THP).

Practical information
When the battery on your vehicle is discharged,
the engine can be star ted using a slave battery (external or on another vehicle) and jump leads.

Starting using another
batter
y

First check that the slave battery has a nominal
voltage of 12 V and a capacity at least equal to
that of the discharged battery.
Do not try to star t the engine by connecting a battery charger.
Do not disconnect the (+) terminal when theengine is running.
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B.)Connect one end of the green or blackcable to the negative terminal (-) of the slave
battery B
(or ear th point on the other vehicle).)Connect the other end of the green or black cable to the negative terminal C
(or the engine mounting) of the broken-down vehicle.
)
Start the engine of the other vehicle andallow it to run for a few minutes.)
Operate the star ter of the broken-down
vehicle and let the engine run.
If the engine does not star t immediately, switch off the ignition and wait a few
moments before trying again.) Wait until the engine returns to idle, then
disconnect the
jump leads in reverse order.


Some functions are not available if the battery is not sufficiently charged.

Changing a front or rear wiper blade
Procedure for replacing a worn wiper blade with a new one without the use of tools.


Before removing a front
w
iper blade
) Within one minute after switching off the ignition, operate the wiper stalk to position
the wiper blades in the ver tical position.
This position must be used in order to avoid
damaging the wiper blade and the bonnet.


Removal
)
Raise the corresponding wiper arm. )
Unclip the wiper blade and remove it.



Fitting
)At the front, check the size of the wiper blade as the shorter blade is fitted to thepassenger side of the vehicle. )Put the corresponding new wiper blade inplace and clip it. )Fold down the wiper arm carefully.



After fitting a front wiper
blade
)Switch on the ignition.)Operate the wiper stalk again to park the
wiper blades.








Load reduction mode System which manages the use of certainfunctions according to the level of chargeremaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates cer tain functions, such as the air conditioning,
th
e heated rear screen...
The deactivated functions are reactivated automatically as soon as conditions permit.

)On the front bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar.)Place the gear lever in neutral (position Nfor an electronic or automatic gearbox).
)On the rear bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar. )Switch on the hazard warning lamps on both vehicles.)Move off gently and drive for a shor t
distance only.
Towing your vehicle Towing another vehicle
Failure to obser ve this special conditioncould result in damage to cer taincomponents (braking, transmission...)and the absence of braking assistancethe next time the engine is started.
)
Unlock the steering by turning the key one
notch in the ignition switch and release the
parking brake.) Switch on the hazard warning lamps onboth vehicles. )
Move off gently and drive for a shor t
distance only.