2014 CITROEN DS3 CABRIO battery

CHECKS PRACTICAL
INFORMATIONTECHNICAL DATA AUDIO AND
TELEMATICS
191Bonnet
192Running out of fuel (Diesel)
193Petrol engines
194 Diesel engines
195 Checking levels
198Checks
202Temporary puncture repair kit
209Changing a wheel
216 Snow chains
217 Changing a bulb
225 Changing a fuse
232Battery
235 Energy economy mode
236 Changing a wiper blade
237 Towing the vehicle
239To w i ng a trailer
241 Advice on care andmaintenance
242Accessories
246 Petrol engines
248 Petrol weights
250 LPG engines
251 LPG weights
252Diesel engines
253 Diesel weights
254 Dimensions
256 Identifi cation markings
261Emergency or assistance
263eMyWay
317 Audio system
012012013013010010011011

Warning lampis onCauseAction / Observations
Engine oil pressure
fixed. There is a fault with the enginelubrication system. You must stop as soon it is safe to do so.
Park, switch off the ignition and contact a CITROËN
dealer or a qualified workshop.
Battery charge fixed. The battery charging circuit has a fault(dirty or loose terminals, slack or cut
alternator belt, ...). The warnin
g lamp should go off when the engine isstarted.
If it does not go off, contact a CITROËN dealer or aqualified workshop.
Door(s) open
fixed if the speed isbelow 6 mph (10 km/h).

A door or the boot is still open. Close the door or boot.
fixed and accompanied by an audible signal if
the speed is above6 mph (10 km/h).

A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation.
The spanner remains on.
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also comeon if you have exceeded the period since the last ser vice, indicated in the maintenance and warranty guide.

Service indicator zero reset

After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the trip distance recorder
zero reset button,) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.
Following this operation, if you wish todisconnect the battery, lock the vehicleand wait at least five minutes for thezero reset to be taken into account.


Retrieving the serviceinformation

You can access the ser vice information at anytime. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for afew seconds, then disappears.
Service overdue
For a few seconds after the ignition is switchedon, the spanner flashes
to indicate that the
service must be carried out as soon as possible.Example:
the ser vice is overdue by 180 miles(300 km).
For a few seconds after the ignition is switched
on, the display indicates:

Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction, you can no longer unlock, lock or locate your
vehicle.)First of all, use the key in the lock to unlock
or lock your vehicle.
)Then, reinitialise the remote control.
If the problem persists, contact a CITROËN
dealer as soon as possible.
Remote control problem
Reinitialisation
)Switch off the ignition.)Turn the key to position 2 (Ignition).)Press the closed padlock immediately for afew seconds.)Switch off the ignition and remove the keyfrom the ignition switch.
The remote control is fully operational again.

Changing the battery

Battery ref.: CR1620 / 3 volts. )Unclip the casing by inserting a coin at the notch and rotating.
)Slide the flat battery out of its location.)Slide the new battery into its location
observing the original direction.
)Clip the casing in place, then the chrome
finisher. )Reinitialise the remote control.

If the batter
y is flat, you are
informed by lighting of this warninglamp in the instrument panel, an audible signal
and a message in the multifunction screen.
) Unfold the key.)
Release the chrome finisher by pressingon lug A.)
Maintain pressure on lug A
and remove thechrome finisher by sliding it off at 45°.

Alarm System which protects and provides a deterrent against the theft of your vehicle. It provides two types of protection, exterior and interior, as well as aself-protection function.
Exterior perimeter
protection
The system detects opening of the vehicle.
The alarm is triggered if anyone tries to enter
the vehicle by forcing a door, the boot or the bonnet.

Interior volumetric
protection

The system detects any variation in the volume
in the passenger compartment.
The alarm is triggered if anyone breaks a
window or moves inside the vehicle.
If you wish to leave a pet in the vehicle or a
window partially open, deactivate the interior
volumetric protection.

Self-protection function

The system detects the putting out of ser vice of its components.
The alarm is triggered if anyone tries to put
the wires of the siren, the central control or the
battery out of ser vice.
Do not make any modifications to the alarmsystem, this could cause malfunctions.

)Press button Afor more than two seconds.
A confirmation message appears on themultifunction screen, accompanied by an audible signal.
Deactivation
)Press button Aagain for more than
two seconds.
A confirmation message appears on themultifunction screen, accompanied by an audible signal.

To lock or unlock the doors mechanicall
y in the event of a central locking system failure or flatbattery.
Emergency control


Locking the driver's door
)
Inser t the key in the lock, then turn it to theleft.


Unlocking the driver's door
)
Inser t the key in the lock, then turn it to the
right.

Locking the passenger's door
)Remove the black cap, on the edge of the
door, using the key. )Inser t the key in the cavity, then turn it fully. )Remove the key and refit the cap.



Unlocking the passenger's door
)Pull the interior door opening control.
In the event of a fault with the central locking system, you must disconnectthe battery to lock the boot and soensure the complete locking of thevehicle.

Driving with the doors locked may make access more difficult for the emergency services in an emergency.

105
Access











Boot


Opening
)After unlocking the vehicle using theremote control or the key, press the
opening control and raise the tailgate.
Closing
) Lower the tailgate using the interior grab
handle.
If the tail
gate is not closed correctly:
-when the engine is running, this
warning lamp comes on, accompanied
b
y a message on the multifunction
screen for a few seconds,
-when the vehicle is moving (speed above6 mph (10 km/h)), this warning lamp comes
on, accompanied by an audible signal and
a message on the multifunction screen for a few seconds.
System for mechanical unlocking of the boot
in the event of a battery or central lockingmalfunction.
Tailgate release

Unlocking
)
Fold back the rear benchseat to gainaccess to the lock from inside the boot.)
Insert a small screwdriver into hole Aof thelock to unlock the tailgate.

Operating fault

With the ignition on, if this warninglamp comes on and AUTOflashes,
accompanied by an audible signal and amessage in the multifunction screen, this
indicates a gearbox fault.Have it checked by a CITROËN dealer or a qualified workshop.
Reinitialisation
(5-speed electronic
gearbox)
In exceptional circumstances, thegearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.
AUTO
and - -
appear in theinstrument panel.
AUTO
and - -
appear in the instrument panel.
)Select position N.)Press the brake pedal. )Wait for around 30 seconds until Nor a gear appears in the instrument panel. )Move the gear lever to position A
, then toposition N.)With your foot still on the brake pedal, start
the engine. The gearbox is operational again. Followin
g disconnection of the battery, it is necessary to reinitialise the gearbox. )Switch on the ignition.
Follow the procedure described above.