2014 CITROEN C-ELYSÉE bulb

.
.
Contents
Direction indicators 100
Hazard warning lamps 100
Horn 100
Braking assistance systems 101
Tr ajectory control systems 102
Front seat belts 103
Airbags 106
Safety
Child seats 110
ISOFIX child seats 116
Child lock 119
Child safety
Te m p o r a ry puncture repair kit 120
Changing a wheel 126
Changing a bulb 133
Changing a fuse 139
Battery 144
Electrical energy economy mode 147
Changing a wiper blade 148
To w i ng the vehicle 149
To w i ng a trailer 151
Very cold climate screen(s) 153
Advice on care and maintenance 154
Accessories 154
Mats 156
Roof bars 157
Practical information
Petrol engines 168
Petrol weights 169
Diesel engine 170
Diesel weights 171
Dimensions 172
Identifi cation markings 173
Technical data
Audio system / Bluetooth 175
Audio system 205
Audio and telematics
Visual search
Alphabetical index Checks
Bonnet 159
Petrol engines 160
Diesel engine 161
Running out of fuel (Diesel) 162
Checking levels 163
Checks 166

74
Fittings
Storage box
)Raise the boot carpet for access to the
storage box.
This has areas
for the storage of a box of spare
bulbs, a first aid kit, two warning triangles...
It also contains the vehicle tools, the temporary puncture repair kit...

133
9
Practical information











Changing a bulb


Front lamps

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of the glass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.

The headlamps are fitted with polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water or apH neutral product,)
when using a high pressure washer on persistent marks, do not keep the lance directed towards thelamps or their edges for too long, so as not to damage their protectivecoating and seals,)
do not touch the bulb directly withyour fingers, use lint-free cloths.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of serious burns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.1
.Direction indicators (PY21W amber).2. Main beam headlamps (H1- 55W).3.Dipped beam headlamps (H7-55W).4.Daytime running lamps / sidelamps(W21/5W).or
Sidelamps (W5W).5.Front foglamps (H11- 55W).

134
Practical information

Amber coloured bulbs, such as thedirection indicators, must be replacedwith bulbs of identical specificationsand colour.
When refitting, close the protective cover carefully to preser ve the sealing of the headlamp.


Rapid flashing of the direction indicator warning lamp (right or left) indicates thefailure of a bulb on that side.
Changing direction indicator bulbs
)Turn the bulb holder an eighth of a turn anti-clockwise and extract it.)Remove the bulb and change it.
To reassemble, carry out these operations in
reverse order.
Changing main beam headlampbulbs
)Remove the protective cover by pulling on
the tab. )Disconnect the bulb connector. )Push the spring to one side to release the bulb.)Remove the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.

135
9
Practical information
Changing dipped beamheadlamp bulbs
)Remove the protective cover by pullingthe tab. )Disconnect the bulb connector by lifting
it off.)Pull the bulb out and change it.
To r e f i t , c a r ry out these operations in reverse order.

Changing daytime running lamp /
sidelamp bulbs
) Pull the bulb holder pressing on the tabs on both sides. )
Remove the bulb and change it.
To r efit, carry out these operations in reverse order.

136
Practical information
Changing front foglamp bulbs
)Access to the front foglamp is through the aper ture below the bumper.
If necessary, unscrew and completely remove the cover.)Turn the bulb holder a quar ter turn anti-clockwise and pull it out. )Disconnect the bulb connector. )Remove the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.
If you experience any difficulty in replacing bulbs, contact your CITROËNdealer or a qualified workshop.
Changing direction indicator side
repeaters
)Insert a screwdriver towards the centre of
the repeater between the repeater and the
base on the body.
)Tilt the screwdriver to extract the repeater and remove it.)Disconnect the repeater connector.)Replace the module.
To r e f i t , c a r ry out these operations in reverse order.
Contact a CITROËN dealer or a qualified workshop to obtain areplacement side repeater module.

137
9
Practical information
Changing bulbs
These bulbs are changed from inside the boot:
) open the boot,)
remove the access grille from thecorresponding side trim panel, )
slacken and remove the nut,
)
disconnect the lamp unit connector,)
unclip the lamp unit by lowering the tongue
and carefully extract it pulling in line
towards the outside,
)remove the four screws and lift off the bulb
holder,
)turn the failed bulb a quar ter of a turn and change it.
To r e f i t , c a r r
y out these operations in reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp. 1
.Direction indicators (PY21W amber).2.Reversing lamps (R10W).3.Foglamp (P21W).4.Sidelamps (P21/5W).5.Brake lamps / sidelamps (P21/5W).



















Rear lamps

138
Practical information
Third brake lamp (5 W5W bulbs)Number plate lamps (W5W)
)Insert a thin screwdriver into one of the
transparent lens.
)Push it outwards to unclip it and remove it. )Remove the failed bulb and change it. To reassemble, carry out these operations inreverse order.
Ensure that the housing cover is correctly positioned on its support before clipping it into place.
To c h a n
ge these bulbs, it is necessary toremove the housing from the rear shelf, working from the rear seats:)pull the housing cover towards you and up
to disengage it,
) disconnect the lamp connector,)
unclip the bulb holder by lifting the two lugs
and remove it,) replace the failed bulb.
To reassemble, carry out these operations in reverse order.