2014 CITROEN C-ELYSÉE check engine

52
Access
When the low fuel level in the tank is reached, this warning lamp comes
on in the instrument panel.
Opening the filler cap may result in an inrush of air. This vacuum is entirely normal and results from the sealing of the fuel system.
























Fuel tank
Capacity of the tank: approximately 50 litres.

A label on the inside of the filler flap reminds you of the type of fuel to use according to your engine.
Additions of fuel must be of at least 5 litres to be registered by the fuel gauge.


Refuelling
)Open the filler cap by turning it a 1/4 turn to
the left.)Remove the filler cap and hang it on its carrier (on the filler flap).)Fill the tank. Do not continue past the thirdcut-off of the nozzle, as this may causemalfunctions. )Refit the filler cap turning it a 1/4 turn to the right. )Push the filler flap to close it.
Opening
)Raise the lever. When it first comes on,
around 5 litres
of fuel
remain in the tank.
You must refuel as soon as possible to avoid
running out.
If you run out of fuel (Diesel), refer the the
"Checks" section.

53
2
Access
Operation
When a petrol filler nozzle is introduced into the
fuel filler neck of your Diesel vehicle, it comesinto contact with the flap. The system remains closed and prevents filling.
Do not persist but introduce a Diesel typefiller nozzle.
















Misfuel prevention (Diesel) * Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of
engine damage that can result from filling with the wrong fuel.
Located in the filler neck, the misfuel prevention device appears when the filler cap is removed.
*
Accordin
g to country of sale.

It remains possible to use a fuel can to fill the tank.In order to ensure a good flow of fuel, do not place the nozzle of the fuel can in direct contact with the flap of themisfuel prevention device and pour slowly.



Tr a v e l l i ng abroad

As Diesel fuel pump nozzles may be different in other countries, thepresence of the misfuel prevention device may make refuelling impossible.
Before travelling abroad, werecommend that you check with the CITROËN dealer network, whether your vehicle is suitable for the fuel pumps inthe country in which you want to travel.
If you have put in the wrong fuel for your vehicle, you must have havethe tank drained and refilled with the correct fuel before you start theengine.


Fuel supply cut-off

Your vehicle is fitted with a safety system that cuts off the supply of fuel in the event of an
impact.

62
Comfort
In order for these systems to be fully effective, follow the operation and maintenance guidelines below: )To obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as wellas the air extractor located in the boot. )Operate the air conditioning system for at least 5 to 10 minutes, once or twice a month to keep it in perfect working order. )Ensure that the passenger compar tment filter is in good condition and have the filter elements replaced regularly. )To ensure correct operation of the air conditioning system, you are also advised to have it checked regularly as recommended in the ser vicing booklet.)If the system does not produce cold air, switch it off and contact a CITROËN dealer or a qualified workshop.
When towing the maximum load on a steep gradient in high temperatures, switching off theair conditioning increases the available engine power and so improves the towing ability.











Recommendations for ventilation and air conditioning


If after an extended stop in sunshine, the interior temperature is very high, firstventilate the passenger compar tment for
a few moments. Put the air flow control at a setting highenough to quickly change the air in the passenger compartment.

The air conditioning system does not contain chlorine and does not present any danger to the ozone layer.


The condensation created by the air conditioning results in a discharge of water under the vehicle which isperfectly normal.

81
5
Driving
AUTO
and -
appear in the instrumentpanel.
)
Select position N.)
Press the brake pedal. )
Wait for around 30 seconds until N
or agear appears in the instrument panel.)
Move the gear lever to position A
, then to
position N.) With your foot still on the brake pedal, start
the engine.The gearbox is operational again.
Reinitialisation
Following disconnection of the battery, it is
necessary to reinitialise the gearbox.) Switch on the ignition.


Before doing anything under the bonnet, ensure that the gear lever is inneutral (position N ) and that the parkingbrake is applied.



In exceptional circumstances, the gearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.
AUTOand -appear in the instrument panel.

For all parking situations, you mustapply the parking braketo immobilise the vehicle.

When immobilising the vehicle with theengine running, you must put the gear lever into neutral (position N)
. Be
fore switching off the engine:


- chan
ge to position N
to be in neutral,
or

- leave the vehicle in gear; in this case the
vehicle cannot be moved.

Follow the procedure described above.



Stopping the vehicle

With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an audible signal and
a message in the multifunction screen, this
indicates a gearbox fault. Have it checked by a CITROËN dealer or a qualified workshop.


Operating fault

102
Safety
Anti-slip regulation (ASR)
and electronic stability
programme (ESP)
The anti-slip regulation (also known as Traction Control) optimises traction to prevent skidding
of the wheels, by acting on the brakes of thedriving wheels and on the engine.
The electronic stability programme acts on the
brake o
f one or more wheels and on the engine to
keep the vehicle on the trajectory required by the
driver, within the limits of the laws of physics.
This is indicated b
y flashing of this
warning lamp in the instrument panel.



The ASR /ESP systems offer exceptional safety in normal driving, butthis should not encourage the driver to take extra risks or drive at high speed.
The correct functioning of these systems depends on obser vation of the manufacturer's recommendations regarding the wheels (tyres and rims),the braking components, the electronic components and the assembly and repair procedures used by theCITROËN dealer network.
After an impact, have these systems checked by a CITROËN dealer or a qualified workshop.



Operating fault

Illumination of the warning lamp,
accompanid b
y a message in the screen indicates a malfunction of
these systems.
Reactivation
These systems are reactivated automatically every time the ignition is switched of, or from
30 mph (50 km/h).) Press this button again to reactivate them
manually.
The lamp in the button goes off.
The symbol going off in the instrument panel
indicates the reactivation of the ASR and ESP
s
ystems.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, ...), it may be advisable to deactivate
the ASR and ESP systems, so that the wheelscan move freely and regain grip.














Trajectory control systems
Activation
These systems are activated automatically each time the vehicle is started.
They come into operation in the event of a grip
or trajectory problem.The displa
y of this symbol indicates
that the ASR and ESP systems are deactivated.
) Press this button button, located on
the dashboard (driver's side), until the corresponding symbol appears in the
instrument panel screen.
The lamp in the button comes on. Contact a CITROËN dealer or a qualified
workshop to have the ASR /ESP s
ystems checked.


Coasting with the engine off results in a loss of power assistance for the steering.

122
Practical information
Repair procedure
)Switch off the ignition.) Uncoil the white pipe G
fully.)
Unscrew the cap from the white pipe.)
Connect the white pipe to the valve of the
tyre to be repaired.

)Connect the compressor's electric plug to
the vehicle's 12 V socket. )Star t the vehicle and leave the engine running.
Take care, this product is harmful (e.g.ethylene-glycol, colophony...) if swallowed and causes irritation to the eyes.Keep this product out of the reach of children.
Avoid removing any foreign bodieswhich have penetrated into the tyre.
1. Sealing
)Turn the selector Ato the "sealant"position.)Check that the switch B
is in position "O".

125
9
Practical information

Removing the cartridge
)Stow the black pipe. )Detach the angled base from the white pipe.)Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.


Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for single use; even if only partly used, itmust be replaced. After use, do not discard the car tridgeinto the environment, take it to an authorised waste disposal site or a CITROËN dealer.
Do not forget to obtain a new sealantcartridge, available from CITROËN dealers or from a qualified workshop.

Checking tyre pressures /
inflating accessories
You can also use the compressor, withoutinjecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).

)
Turn the selector Ato the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
) Connect the compressor's electrical connector to the vehicle's 12 V socket. )
Star t the vehicle and let the engine run. )
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. ) Remove the kit then stow it.

145
9
Practical information
Starting using another
battery
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B .)Connect one end of the green or blackcable to the negative terminal (-) of the slave battery B.
)
Connect the other end of the green or blackcable to the ear th point C
on your vehicle (engine mounting).)
Operate the star ter, let the engine run.)
Wait until the engine returns to idle and disconnect the cables.

Charging the battery using
a battery charger
)
Disconnect the battery from the vehicle.)
Follow the instructions for use provided by
the manufacturer of the charger. ) Connect the battery starting with the
negative terminal (-).)
Check that the terminals and connectors
are clean. If they are covered with sulphate (whitish or greenish deposit), remove themand clean them.