2014 BMW 2 SERIES low beam

The system is not fully functional in situations
such as the following, and driver intervention
may be necessary:▷In very unfavorable weather conditions,
such as fog or heavy precipitation.▷When detecting poorly-lit road users such
as pedestrians, cyclists, horseback riders
and wagons; when driving close to train or
ship traffic; and at animal crossings.▷In tight curves, on hilltops or in depres‐
sions, in cross traffic or half-obscured on‐
coming traffic on freeways.▷In poorly-lit towns and cities and in the
presence of highly reflective signs.▷At low speeds.▷When the windshield behind the interior
rearview mirror is fogged over, dirty or cov‐
ered with stickers, etc.
Fog lights
Front fog lights
The low beams must be switched on.
Press button. The green indicator
lamp lights up.
If the automatic headlight control, refer to
page 90, is activated, the low beams will come
on automatically when you reel on the front fog
lights.
When the high beams or headlight flasher are
activated, the front fog lights are not switched
on.
Instrument lighting
Adjusting The parking lights or low beams
must be switched on to adjust
the brightness.
Adjust the brightness with the
thumbwheel.
Interior lights
General information
The interior lights, footwell lights, access lights
and courtesy lights are controlled automati‐
cally.
Thumb wheel for the instrument lighting con‐
trols brightness of some of these features.1Interior lights2Reading lamp
Switching the interior lights on and off
Press button.
To reel off permanently: press the button for
approx. 3 seconds.
Switch back on: press button.
Reading lights Press button.
Seite 92ControlsLights92
Online Edition for Part no. 01 40 2 956 568 - X/14

Danger of burns
Only change bulbs when they are cool;
otherwise, there is a danger of getting
burned.◀
Working on the lighting system
When working on the lighting system,
you should always reel off the lights affected to
prevent short circuits.
To avoid possible injury or equipment damage
when replacing bulbs, observe any instructions
provided by the bulb manufacturer.◀
Do not perform work/bulb replacement
on xenon headlights
Have any work on the xenon lighting system,
including bulb replacement, performed only by
a service center. Due to the high voltage
present in the system, there is a danger of fatal
injuries if work is carried out improperly.◀
Do not touch the bulbs
Do not touch the glass of new bulbs with
your bare hands, as even minute amounts of
contamination will burn into the bulb's surface
and reduce its service life.
Use a clean tissue, cloth or something similar,
or hold the bulb by its base.◀
Light-emitting diodes (LEDs)
Some items of equipment use light-emitting
diodes installed behind a cover as a light
source.
These light-emitting diodes, which are related
to conventional lasers, are officially designated as Class 1 light-emitting diodes.
Do not remove the covers
Do not remove the covers, and never
stare into the unfiltered light for several hours;
otherwise, irritation of the retina could result.◀Headlight glass
Condensation can form on the inside of the ex‐
ternal lights in cool or humid weather. When
driving with the light switched on, the conden‐
sation evaporates after a short time. The head‐
light glass does not need to be changed.
If the headlights do not dim despite driving
with the light switched on, increasing humidity
forms, e. g. water droplets in the light, have the service center check this.
Headlight setting The headlight adjustments can be affected by
changing lights and bulbs. Have the head‐
lights' settings checked and corrected by serv‐
ice after a replacement.
Front lights, bulb replacement
Halogen headlights
At a glance1Daytime running lights/high beams/head‐
light flasher2Parking lights3Low beams4Turn signalSeite 188MobilityReplacing components188
Online Edition for Part no. 01 40 2 956 568 - X/14

Accessing the turn signals and low beams
Follow general instructions, refer to page 187.1.In the wheel house, loosen the two brack‐
ets and remove the cover.
Turn signal
21-watt bulb, PY21W
1.If necessary, pull the inside trim of the
wheel house slightly inward. Turn the bulb
socket counterclockwise and remove.2.Press the bulb gently into the socket, turn
counterclockwise and remove.3.Install the new bulb and bulb holder in re‐
verse order of removal.4.Attach the cover to the wheel house.Low beams
55-watt bulb, H7.1.Turn the cover counterclockwise and re‐
move.2.Tilt the bulb down and then up to loosen it
from the holder and remove.3.Pull the connector off the bulb.4.Attach the connector to the new bulb.5.First insert the bulb at the top with the
strap, arrow 1, and then press down firmly,
arrow 2. The bulb must audibly latch in
place.6.Close the headlight housing with the lid.
Make sure that the lid engages.7.Attach the cover to the wheel house.Seite 189Replacing componentsMobility189
Online Edition for Part no. 01 40 2 956 568 - X/14

Accessing the daytime running lights, high
beams/headlight flasher and parking lights
Follow general instructions, refer to page 187.1.Open the hood, refer to page 180.2.Turn the cover counterclockwise and re‐
move.
Daytime running lights and high beams/
headlight flasher
55-watt bulb, H15.
1.Turn the bulb counterclockwise and re‐
move.2.Install the new bulb in reverse order of re‐
moval. Turn the clockwise bulb here until it
hits the stop.3.Close the headlight housing with the lid.
Make sure that the lid engages.Parking lights
6-watt bulb, H6W.1.Tilt the bulb holder down and then up to
loosen it from the holder and remove it.2.Carefully remove the bulb from the bulb
holder.3.To insert the new bulb, proceed in reverse
order of removal. Make sure you hear the
bulb holder engage.4.Close the headlight housing with the lid.
Xenon headlights
Hints
Because of the long life of these bulbs, the
likelihood of failure is very low. Switching the
lights on and off frequently shortens their life.
If a bulb fails, reel on the front fog lights and
continue the trip with great care. Comply with
local regulations.
Do not perform work/bulb replacement
on xenon headlights
Have any work on the xenon lighting system,
including bulb replacement, performed only by
a service center. Due to the high voltage
present in the system, there is a danger of fatal
injuries if work is carried out improperly.◀
For checking and adjusting headlamp aim,
please contact your BMW center.
Seite 190MobilityReplacing components190
Online Edition for Part no. 01 40 2 956 568 - X/14

At a glance1Parking lights / daytime running lights2Low beams/high beams/headlight flasher3Turn signal
Xenon headlights
Low beams and high beams are designed with
xenon technology.
The parking lights and daylight running lights
are made using LED technology.
Contact your service center in the event of a
malfunction.
Turn signal
Follow general instructions, refer to page 187.
21-watt bulb, PY21W1.In the wheel house, loosen the two brack‐
ets and remove the cover.2.If necessary, pull the inside trim of the
wheel house slightly inward. Turn the bulb
socket counterclockwise and remove.3.Press the bulb gently into the socket, turn
counterclockwise and remove.4.Install the new bulb and bulb holder in re‐
verse order of removal.5.Attach the cover to the wheel house.
Front fog lights
Follow general instructions, refer to page 187.
35-watt bulb, H8.
1.Use the back side of the screwdriver from
the onboard vehicle tool kit to remove the
three wheel house panel screws, arrow 1.Seite 191Replacing componentsMobility191
Online Edition for Part no. 01 40 2 956 568 - X/14

other attempt in order to allow the dis‐
charged battery to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the re‐
verse order.
Check the battery and recharge if needed.
Tow-starting and towing Note Tow-starting and towing
For towing the vehicle turn, switch off the
Intelligent Safety systems; otherwise malfunc‐
tions of the individual braking systems might
lead to accidents.◀
Manual transmission Gearshift lever in neutral position.
Towing Follow the towing instructions
Follow all towing instructions; otherwise,
vehicle damage or accidents may occur.◀
▷Make sure that the ignition is switched on;
otherwise, the low beams, tail lights, turn
signals, and wipers may be unavailable.▷Do not tow the vehicle with the rear axle
tilted, as the front wheels could turn.▷When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.▷Larger steering wheel movements are re‐
quired.▷The towing vehicle must not be lighter
than the vehicle being towed; otherwise,
it will not be possible to control the vehi‐
cle's response.Tow truck
With rear-wheel drive
Your vehicle should be transported with a tow
truck with a so-called lift bar or on a flat bed.
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
With xDrive
The vehicle should only be transported on a
loading platform.
Do not tow with only the front or rear axle
raised
Do not tow the BMW with just the front or rear
axle raised; otherwise, the wheels could lock
up and the transfer case could be damaged.◀
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
Seite 200MobilityBreakdown assistance200
Online Edition for Part no. 01 40 2 956 568 - X/14

F
Failure message, see Check Control 77
False alarm, refer to Uninten‐ tional alarm 44
Fan, refer to Air flow 129, 132
Filler neck for engine oil 182
Fine wood, care 205
First aid kit 198
Fitting for towing, see tow fit‐ ting 201
Flat tire, changing wheels 193
Flat Tire Monitor FTM 100
Flat tire, Tire Pressure Moni‐ tor TPM 97
Flat tire, warning lamp 98, 101
Flooding 151
Floor carpet, care 206
Floor mats, care 206
Fogged up windows 129
Fold down the rear seat back‐ rest, see Though-loading
system 141
Fold-out position, wiper 70
Foot brake 151
Front airbags 94
Front-end collision warning with City Braking func‐
tion 103
Front fog lights 92
Front fog lights, front, bulb re‐ placement 191
Front lights 188
front-seat passenger airbags, automatic deactivation 96
Front-seat passenger airbags, indicator lamp 96
FTM Flat Tire Monitor 100
Fuel 168
Fuel consumption, current 81 Fuel consumption, refer to
Average fuel consump‐
tion 86
Fuel filler flap 166
Fuel gauge 80
Fuel lid 166
Fuel quality 168
Fuel recommendation 168
Fuel, tank capacity 212
Fuse 195
G Garage door opener, refer to Universal Integrated Remote
Control 135
Gasoline 168
Gear change, Steptronic transmission 72
Gear shift indicator 82
General driving notes 150
Glare shield 139
Glass sunroof, powered 46
Glove compartment 143
Gross vehicle weight, ap‐ proved 211
H Halogen headlights, bulb re‐ placement 188
Handbrake, refer to parking brake 67
Hand-held transmitter, alter‐ nating code 136
Hazard warning flashers 197
Head airbags 94
Headlight control, auto‐ matic 90
Headlight courtesy delay fea‐ ture 89
Headlight flasher 68
Headlight flasher, bulb re‐ placement 190
Headlight glass 188
Headlights 188 Headlights, care 204
Headlight washer system 68
Head restraints 48
Head restraints, front 53
Head restraints, rear 54
Heavy cargo, stowing 154
High-beam Assistant 91
High beams 68
High beams/low beams, refer to High-beam Assistant 91
High beams, bulb replace‐ ment 190
Hills 152
Hill start assistant, refer to Drive-off assistant 115
Hints 6
Holder for beverages 145
Hood 180
Horn 14
Hotel function, trunk lid 40
Hot exhaust system 151
Hydroplaning 151
I Ice warning, see External temperature warning 81
Icy roads, see External tem‐ perature warning 81
Identification marks, tires 174
Identification number, see ve‐ hicle identification num‐
ber 9
iDrive 18
Ignition key, refer to Remote control 34
Ignition off 63
Ignition on 63
Indication of a flat tire 98, 101
Indicator and alarm lamps, see Check Control 77
Indicator lamp, see Check Control 77
Individual air distribu‐ tion 129, 132 Seite 217Everything from A to ZReference217
Online Edition for Part no. 01 40 2 956 568 - X/14

Individual settings, refer toPersonal Profile 35
Inflation pressure, tires 170
Inflation pressure warning, tires 100
Info display, refer to Com‐ puter 85
Initialize, Tire Pressure Moni‐ tor TPM 98
Initializing, Flat Tire Monitor FTM 101
Instrument cluster 76
Instrument cluster, electronic displays 76
Instrument lighting 92
Integrated key 34
Integrated Owner's Manual in the vehicle 29
Intelligent Emergency Re‐ quest 197
Intelligent Safety 102
Intensity, AUTO pro‐ gram 131
Interior equipment 135
Interior lights 92
Interior lights via remote con‐ trol 37
Interior motion sensor 44
Interior rearview mirror, auto‐ matic dimming feature 57
Interior rearview mirror, com‐ pass 137
Interior rearview mirror, man‐ ually dimmable 57
Interval display, service re‐ quirements 81
J Jacking points for the vehicle jack 194
Joystick, Steptronic transmis‐ sion 72
Jump-starting 198 K
Key/remote control 34
Keyless Go, refer to Comfort Access 41
Key Memory, refer to Per‐ sonal Profile 35
Kickdown, Steptronic trans‐ mission 71
Knee airbag 94
L
Lamp replacement 187
Lamp replacement, front 188
Lamp replacement, rear 192
Lane departure warning 108
Lane margin, warning 108
Language on Control Dis‐ play 88
Lashing eyes, securing cargo 154
LATCH child restraint sys‐ tem 60
Launch Control 74
Leather, care 205
LEDs, light-emitting di‐ odes 188
Letters and numbers, enter‐ ing 25
Light alloy wheels, care 205
Light control 90
Light-emitting diodes, LEDs 188
Lighter 139
Lighting 89
Lighting via remote con‐ trol 37
Light reel 89
Lights 89
Lights and bulbs 187
Load 154
Loading 153
Lock, door 38
Locking/unlocking via door lock 38 Locking/unlocking with re‐
mote control 37
Locking, automatic 43
Locking, settings 42
Locking via trunk lid 40
Low beams 89
Low beams, automatic, refer to High-beam Assistant 91
Lower back support 50
Luggage rack, see Roof- mounted luggage rack 155
Lumbar support 50
M
Maintenance 185
Maintenance require‐ ments 185
Maintenance, service require‐ ments 81
Maintenance system, BMW 185
Make-up mirror 139
Malfunction displays, see Check Control 77
Manual air distribu‐ tion 129, 132
Manual air flow 129, 132
Manual mode, Steptronic transmission 72
Manual operation, door lock 38
Manual operation, exterior mirrors 56
Manual operation, fuel filler flap 166
Manual operation, Park Dis‐ tance Control PDC 120
Manual operation, rearview camera 122
Manual transmission 71
Marking on approved tires 177
Marking, run-flat tires 178
Master key, refer to Remote control 34 Seite 218ReferenceEverything from A to Z218
Online Edition for Part no. 01 40 2 956 568 - X/14