2014 AUDI R8 SPYDER remove seats

you will be out of position. Always adjust
the driver's or front passenger seat when
the vehicle is not moving.
- Be careful when adjusting the seat
height. Check to see that no one is in the
way, or serious injury could result!
- Because the seats can be electrically ad­ justed with the ignition key removed, never leave children unattended in the
vehicle. Unsuperv ised use of the electr ic
seat adjustments may cause serious in­
jury.
- To reduce the r isk of injury in the case of
sudden braking or accident, front pas­
sengers must neve r ride in a moving ve­
hicle wi th the seatback recl ined. Safety
belts and the airbag system offer maxi ­
mum protection on ly when the seatback
is upright and the safety belts are prop­
erly posit ioned on the body. The more
the seatback is reclined, the greater the
risk of personal injury from an incorrect
seating pos ition and improperly posi­
tioned safety belts!
- Always make sure the front seatbacks are
in the upright posit ion and securely
locked in place when dr iv ing .
Head restraints
Adjusting head restraints
The head restraints must be adjusted proper­
ly to provide protection.
Fig . 66 Drive r's seat head restraint: adjusting the
height
The head restraints on the front seats can be
adj usted to p rov ide safe support to head and
neck at the opt imum he ight. When opt imally
S ea ts a nd s to rage 59
adjusted, the top of the restraint should be
level with the top of the head
c::> page 96.
'" Grasp the s ides of the head restraint with
both hands and slide it upward/downward
until you fee l it click into place
c::> fig . 66.
& WARNING ~ -
- Driving without head restraints or with
head restra ints that are not properly ad­
justed increases the risk of serious or fa­
tal neck injury dramat ically.
- Read and heed all WARNINGS
<=:>page 96.
@ Tips
Correctly adjusted head restraints and
safety be lts are an extremely effective
combination of safety features.
Cup holder
F ig. 67 Cup holder
A WARNING
Spilled hot liquid can cause an accident
and personal injury.
-
- Never carry any beverage containers with
hot liq uids, such as hot coffee or hot tea,
in the vehicle while it is moving. In case
of an acc ident, sudden braking or other
veh icle movement, hot liquid could spill,
causing scalding burns. Spilled hot liquid
can also cause an accident and personal injury.
- Use only soft cups in the cupholder . Hard
cups and glasses can cause injury in an
accident.

60 Seats and st o rage
- Never use the cupho lder or adapter as an
ashtray- risk of f ire.
CD Note
On ly drink containe rs with lids should be
carried in the cupho lder. Liquid could spill
out and damage your vehicle's e lectronic
equ ipment or sta in the upholstery, etc.
Ashtray
Fig . 68 Center console: ashtray
The asht ray is inserted in the cupholder.
Opening the ashtra y
... Fold the cover upward.
Emptying the a shtray
,.. Lift the closed ashtray up o ut of the cu­
pholder.
A WARNING
Never put waste paper in the ashtray. Hot
ashes or other hot objects in the ashtray
cou ld set waste paper on fire.
Cigarette Lighter/
socket
N
-"' 0 ..:. ... m
The c igarette lig hte r or socket only wo rk with
the ign ition on.
Using the cigarette lighter
,.. Slide the cover open to reach the cigarette
lighter
qpage 60.
> Push the knob in.
,.. Wait unt il the cigarette lighte r knob pops
out. ,..
Remove the cigarette lighter immediately
and use it .
... Reinsert cigarette lighter into the socket af ­
ter use.
Connecting an a ppliance
,.. Slide t he cover open to reach the c igarette
lighter .
,.. Remove cigarette lighter .
... Plug in appliance to be used.
T he socket of the c igarette lighter may be
u sed for 12-volt appliances with maximum
consumption of up to 100 watts, such as a
flash light, small vacuum cleaner, etc.
A WARNING
-Improper use of the cigarette lighter can
cause ser ious injury or start a fire.
- Be careful when using the c igarette light­
er. If you do not pay attention to what
you are doing when you are us ing the cig­
arette lighter you can burn you rself.
CD Note
- To avoid damaging the socket, only use
plugs t hat fit properly.
- Only use the cigarette lighter socket as a
power source for e lectr ica l accessories
for short durations . Use t he sockets in
the vehicle when a power source is need­ ed for longer du rat ions .
(0 Tips
-When the eng ine is off and accessories
are st ill plugged in and are on, t he vehi­
cle battery can still be d ra in ed.
- The ve hicle battery must not be charged
w ith a standard small charger that pl ugs
into the cigarette lighter or outlet .
Storage
, General
A WARNING
- Always remove objects from the instru­
men t pa nel. A ny items not put away
-

The belt may also lock when you drive up or
down a steep hill or through a sharp curve.
During normal driving the belt lets you move
freely .
Safety be lt pretensioners
The safety belts are equipped with a belt pre­
tensioner that helps to tighten the safety belt
and remove slack when the pretensioner is ac­
tivated . The function of the pretensione r is
monitored by a warning light ¢
page 14.
Switchable locking feature
Every safety belt except the one on the driver
seat is equipped with a switchable locking fea ­
ture that
must be used when the safety belt is
used to attach a child seat. Be sure to read the important information about this feature
¢page 140.
A WARNING
Improperly positioned safety belts can
cause serious injury in an accident
¢ page 107, Safety belt position .
-Safety belts offer optimum protection
only when the seatback is upright and
belts are properly positioned on the
body.
-
- Never attach the safety belt to the buck­
le for another seat. Attaching the belt to
the wrong buckle will reduce safety belt
effect iveness and can cause serious per­
sonal injury.
- A passenger who is not properly restrain­
ed can be seriously injured by the safety
belt itself when it moves from the stron­
ger parts of the body into critical areas
like the abdomen.
- Always lock the convertible locking re­
tractor when you are securing a child
seat in the vehicle
r:::> page 142.
Safety belts 107
Safety belt position
Correct belt position is the key to getting
maximum protection from safety belts .
Fig. 114 Safety belt position
;;;
9 r ., a,
Standard features on your vehicle help you ad­
just the position of the safety belt to match
your body size.
- height-adjustable front seats.
A WARNING
Improperly positioned safety belts can
cause serious personal injury in an acci­
dent.
-
- The shoulder belt should lie as close to
the center of the collar bone as possible
and should fit well on the body. Hold the
belt above the latch tongue and pull it
evenly across the chest so that it sits as
low as possible on the pelvis and there is
no pressure on the abdomen . The belt
should always fit snugly
r:::> fig . 114. Pull
on the belt to tighten if necessary.
- The lap belt portion of the safety belt
must be positioned as low as possible
across pelvis and never over the abdo­
men . Make sure the belt lies flat and
snug ¢
fig. 114. Pull on the belt to tight­
en if necessary.
- A loose-fitting safety belt can cause seri­
ous injuries by shifting its position on
your body from the strong bones to more
vulnerable, soft tissue and cause serious injury.
- Always read and heed all WARNINGS and
other important information
r:::> page 105.

118 Airbag system
components is detected. The function of the
airbag indicator light is described in greater
detail below. Because the front passenger
seat contains important parts of the Ad­
vanced Airbag System, you must take care to prevent it from being damaged . Damage to
the seat may prevent the Advanced Airbag for
the front passenger seat from doing its job in
a crash .
The front Advanced Airbag System
consists of the following:
-Crash sensors in the front of the vehicle that
measure vehicle acceleration/deceleration
to provide information to the Advanced Air­ bag System about the severity of the crash.
- An electronic control unit, with integrated
crash sensors for front and side impacts .
The control unit "decides " whether to fire
the front airbags based on the information received from the crash sensors. The control
unit also "decides" whether the safety belt
pre tensioners should be activated.
- An Advanced Ai rbag with gas generator for
the driver inside the steering wheel hub.
- An Advanced Airbag with gas generator in­
side the inst rument panel for the front pas­
senger.
- A weight-sensing mat under the upholstery
padding of the front passenger seat cushion
that measures the total weight on the seat.
The information registered is sent continu ­
ously to the electronic control unit to regu­
late deployment of the front Advanced Air­
bag on the passenger side.
- An airbag monitoring system and indicator
light in the instrument cluster
¢page 121.
- The PASSENGER AIR BAG OFF light comes
on and stays on in the center of the instru­
ment panel ¢
page 122, fig. 120 and tells
you when the front Advanced Airbag on the passenger side has been turned off.
- A sensor below the safety belt latch for the
front seat passenger to measure the tension
on the safety belt. The tension on the safety
belt and the weight registered by the
weight-sensing mat help the control unit "decide" whether the front airbag for the front passenger seat should be turned off or
not
¢ page 112, Child restraints on the
front seat -some important things to
know.
- A sensor in the safety belt latch for the driv­
er and for the front seat passenger that
senses whether that safety belt is latched or not and transmits this informa tion to the
electronic control unit .
.&_ WARNING
Damage to the front passenger seat can
prevent the front airbag from working
properly.
- Improper repair or disassembly of the
front passenger and driver seat will pre­
vent the Advanced Airbag System from
functioning properly.
- Repairs to the front passenger seat must
be performed by qualified and properly
trained workshop personnel.
- Never remove the front passenger or
driver seat from the vehicle.
-Never remove the upholstery from the
front passenger seat.
- Never disassemble or remove parts from
the seat or disconnect wires from it.
- Never carry sharp objects in your pockets
or place them on the seat. If the weight­
sensing mat in the passenger seat is
punctured it cannot work properly.
- Never carry things on your lap or carry
objects on the passenger seat. Such
items can increase the weight registered
by the weight-sensing mat and send the
wrong information to the airbag control
unit.
- Never store items under the front pas­
senger seat. Parts of the Advanced Air­
bag System under the passenger seat
could be damaged, preventing them and
the airbag system from working proper­ ly.
- Never place seat covers or replacement
upholstery that have not been specifical­ ly approved by Audi on the front seats .
- Seat covers can prevent the Advanced
-
Airbag System from recognizing child .,..

162 Cleaning and protection
Plastic parts and imitation leather
You can clean plastic parts and imitation
l eathe r with a damp cloth .
If this does not re­
move the dirt, you can treat these parts only
with specia l
sol vent-free pla st ic cleaning and
care product s.
A WARNING
So lvents can change the properties of
some plastics and make it harder for the
airbag to dep loy .
- Never clean the instrument pane l or the
surface of Airbag modules with cleaning
products that contain solvents .
- Products containing solvents w ill make
the surface of th is part porous.
- Serious injur ies can result if plastic parts
come loose when the airbag is deployed.
- Always read and heed all WARNINGS and
the informat ion
¢ page 156 .
Cleaning agents containing solvents will
attack the material and can change the
way it behaves.
Carbon-fiber parts
App lies to vehicles: with carbon-fibe r parts
The carbon-fiber parts of your vehicle have a
p a inted su rface . They do not require any spe­
cial care and are cleaned like plast ic parts
¢ page 162 .
Fabrics and fabric coverings
Fab rics and fabr ic coveri ngs (e.g. seats, doo r
tr im panels, etc.) should be cleaned a t reg ular
inte rva ls with a vacu um cleaner. This removes
surface dirt particles which could become em­
bedded in th e fabric thro ugh use. Steam
cleaners shou ld not be used, because the
s team tends to push the dir t deeper into the
f abric and lock i t there.
Normal cleaning
Gener ally, we re commend using a soft sponge
o r a lint -free microfibe r cloth to the clean fab ­
ric. Brushes s hou ld only be used for carpets
and floor mats, since other fab ric surfaces
could be harmed by b rushes.
Norma l su rface s tains can be cleane d using a
commercially availab le foam cleaner . Spread
the foam on the s urface of the fabric with a
soft sponge and work it in gently . Do not satu­
rate the fabric. Then pat the foam dry us ing
absorbe nt, dry cloths (e .g. m icrofiber cloth)
and vacuum i t after it has dried completely .
Cleaning stains
Stains caused by beverag es (e .g. coffee, fr uit
j uice, etc .) can be treated with a mild deter­
gen t solution. Apply the detergent solution
with a spo nge . In the case of stubborn stains,
a detergent paste can be applied directly to
the stain and worked i nto the fabric. After­
wards, use copious amounts of clean wa ter to
remove the rema ining deterge nt. App ly the
wate r w ith a damp doth or sponge and pat
th e fabric dry wi th an abso rbent, dry cloth .
Stai ns from choco late or ma keup should have
de tergent pa ste (e.g. ox-gall so ap) rubbed in­
to them. Afterwa rds, remove the soap wi th
water (damp sponge) .
Alcohol can be used to treat sta ins from
grease, o il, lipstick or a ballpoint pen . M elted
grease or dye mus t be patted off using a b­
sorbent ma terial.
It may be necessary to re ­
treat the areas with detergent paste and wa ­
ter.
In the case of gene ral soiling of the upho ls­
tery and cover material, we recommend hiring
a specia list t hat has the equipment to clean
the seat covers and other fabr ic surfaces by
shampooing and spray extraction.
A WARNING
-A lways read and heed all WARNINGS and
the information
¢ page 156.

@ Tips
Open Velcro fasteners on your clothing can
damage the seat cover. Please make sure
that Velcro fasteners are closed.
Natural leather
App lies to vehicles: with natura l leather
Audi makes great efforts to maintain the
properties , natural look and feel of interior
leather.
G ene ra l
We offer many different types of leather on
our veh icles. Most are different types of nappa
leather, which has a smooth surface and
comes in various co lors .
The intensity of the color determines the visu ­
al characteristics and appearance . If the sur­
face of the leather has a typical natural look,
then the leather is a nappa leather that has
been left in a relatively natural condition. This
leather offers particularly good comfort and
breathes well. F ine veins, closed grains, insect
b ites, skin folds, and subtle variations in co lor
remain visible . These cha racte ristics demon­
strate that the mater ia l is na tural.
Natural nappa leather is not covered by a col ­
or finish .
It is therefore more sensitive to so il­
ing and wear, wh ich is something you need to
consider if ch ild ren, an imals o r othe r factors
m ight prove to be particularly hard on the
l eather .
By contrast, leather types that are cove red by
a co lored finish laye r are more durable. This
h as a posit ive effect on the leather's resist­
ance to wear and soiling in daily use . On the
other hand, the typical characteristics of natu­
ra l leather are bare ly or not apparent. Howev­
er, this does not mean that the leather itself
is of infer ior quality.
Ca re and handling
Because of the exclusive nat ure of the types of
l eather that Audi uses and their unique prop­
erties (such as sensitivity to oils, grease, soi l­
ing, etc.), you will need to be somewhat care-
Cleaning and protec tion 163
ful with these leathers, and a ce rtain type of
care is required. For example, dark clothing
mater ia ls can disco lor leather seats (especia l­
l y if such clothing is damp and was not dyed
correctly) . Dust and dirt particles in pores,
folds, and seams can have an abrasive effect
and can damage the leather surface as well as
weaken seams .
The leather should be cleaned regularly as needed . After having been used for a relat ively
long time, your leather seats will acqu ire a
rich aged fin ish . This is a character istic of nat­
ural leathe r and a s ign of true quality.
In order to maintain the value of this natural
product over the life of your ve hicle, you
shou ld follow the recommendat ions below:
(D Note
- To keep your leather from b leac hing out,
do not allow it to be exposed to bright
sunlight for long periods of time . If you
have to leave the veh icle parked outside
for long per iods, cover the leather to
protect it from direct exposure to s un­
light.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on belts can
leave permanent sc ratches or scrape
marks on the surface of the leather .
{i) Tips
-After each time you clean the leather and
at regular intervals, use a leather preser­
vative creme that contains UV-b lockers
and that works into the leather. Th is
creme will nour ish and mo isturize the
leather, helping it to breathe and stay
supple . It also helps to build up a protec­
tive coating on the surface .
- Clean the leather every 2 - 3 months,
and clean any areas that get soiled.
- Remove fresh marks made by ballpo int
pens, ink, lipstick, shoe polish, etc. as
soon as poss ible.
- Preserve the color of the leather as need­
ed by us ing a special colored leather care
creme to touch up areas of uneven color . •
•