78 On the road
note that e lectrica l equipment such as
exterior lights wi ll switch off as well
when that happens .
Switching engine off
Applies to vehicles: with conven ience key
._ Bring your vehicle to a complete stop.
._ Move the selector lever to the P or N pos i
t ion .
._ Press the
I START ENGINE STOPI button
9 page 77, fig. 91.
Steering lock
The steering locks when you turn the engine
off us ing the
I STAR T ENGINE STOP I button
and open the dr iver's door. The locked steer
i ng helps prevent vehicle theft .
Emergency off
If necessary, the engine can be sw itched off
with the selector lever in the R or D/S pos i
tions. To do so, step on the brake pedal and
press and hold the
I START ENGINE STOP I but
ton vehicle speed must be less than 6 mph (10 km/h).
_& WARNING
- N ever turn off the eng ine before the ve
hicle has come to a comple te stop . The
f ull function o f the brake booster and the
powe r steering is not guara nteed . You
must use more force to turn or brake if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to crashes and serious injur ies.
- For safety reasons, you should always
park your vehicle with the se lector lever
in P. Otherwise, the ve hicle could inad
vertent ly roll away.
-The rad iator fan can continue to ru n for
up to 10 m inutes even afte r yo u have
tu rned off the eng in e and removed the
ignition key. The radiator fa n can also
t u rn on again i f th e e ngine cool ant hea ts
up because of intense sunlight or hea t
build -up in the engine compartment. -
Always take the key with you whenever
you leave your veh icle. Otherw ise, the
engine could be started or electrical
equ ipment such as the power windows
could be ope rated. This can lead to seri
ous injury.
(D Note
If the engine has been under heavy load
for an extended period, heat bu ilds up in
the e ngine compartment after the eng ine
i s sw itched off - there is a r isk of damag ing
the engine. Allow the engine to run at id le
fo r about two minutes before switching it
off.
Driver messages
Ignition i s on
This message appears and a warning tone
sounds if you open the driver's door when the
ignition is sw itched on.
No key ident ified
This message appears when the
I S TART ENGINE STOPI button is pressed if
t h ere is no master key ins ide the ve hicle or if
the system does not recognize it. For exam
ple, the master key cannot be recognized if it
i s covered by an object (e.g . al uminum brief
case) which
screens the radio s ignal. Electron
i c dev ices such as cell phones can also i nte r
f ere with the radio s ignal.
Pres s bra ke p edal to start engine
This message appears if you do not press the
brake pedal to start the eng ine .
Shift to N or P to start engine
Th is mess age appears w hen at tempt ing to
sta rt the eng ine if the selecto r lever for the
automatic transmission is not in the P or N
pos ition . The engine can only be started with
the selecto r in these positions.
Is the key in the vehicle ?
This message appears if the master key is re
moved from the vehicle with the engine run
n ing.
If the master key is no longer in the ve
hicle, you cannot switch on the ignition after
stopping the engine and you also cannot start
the engine again . Moreover, you cannot lock
the vehicle from the outside w ith the key.
Shift to P otherwise vehicle can roll away.
Doors do not lock if lever is not in P.
This message appears for safety reasons
along w ith a warning signa l. It appears if the
selector lever for the automat ic transm ission
is not in the P position when switch ing off the
ignition. Move the selector lever to the P posi
tion, otherw ise the veh icle is not secured
against rolling away . You also cannot lock the
veh icle using the locking button* on the door
handle or using the remote key.
Convenience key defective! Use ignition lock
This message appears if the engine must be
started or stopped using the ignition key and
not the
I STAR T ENGIN E STOP ! button .
Electromechanical
parking brake
Operation
The electromechanical parking brake replaces
the hand brake.
F ig. 92 Cen ter console: Pa rk ing brake
.. Pull on the switch @c> fig . 92 to apply the
parking brake. The indicator light in the
switch illum inates .
.. Step on the brake pedal or the acce le rator
pedal and press the switch at the same time
On the road 79
to release the parking brake. The indicator
light in the switch goes out .
Your vehicle is equipped wi th an electrome
chanical parking brake. The parking brake is
designed to prevent the vehicle from rolling
unintentionally and replaces the hand brake.
In addition to the normal functions of a tradi
tiona l hand brake, the electromec hanical
parking brake provides various convenience
and safety funct ions .
When starting from rest
-The integral start ing ass ist helps you when
driving by automatically releasi ng the park
ing brake
¢ page 80, Starting from rest.
-When starting on inclines, the starting as
sist prevents the vehicle from unintentiona l
ly rolling back. The braking force of the
parking brake is not re leased until sufficient
driving force has been bui lt up at the
wheels.
Emergency brake function
An emergency brake ensures that the veh icle
can be slowed down even if the
normal brakes
fail
c> page Bl, Emergency braking.
Indicator lights
- If the parking brake is closed with the ign i
t ion
switched on the . (USA models) /
• (Canada models) indicator lights come
on in the instrument cluster and the switch.
- If the parking brake is closed with the igni
tion
switched off the. (USA models) /
• (Canada models) indicator lights come
on in the instrument cluster and the switch
for about 20 seconds.
A WARNING
If a drive range is engaged with the vehicle
stationary and the engine runn ing, you
must in no instance accelerate carelessly .
Othe rwis e the vehicle w ill start to move
imm ediately- risk of an accident.
80 On the road
(0 Note
If the . symbol i n the display or the.
(USA models) . (Canada models) indica
tor light in the instrument cluste r flashes
'
there is a malfunction in the brake system.
By pressing the
IS ET I button, you can br ing
up a driver message which explains the
malfunct ion in more detai l. If the driver
message
Parking brake! appears , the re is
an operating malfunct io n in t he par king
bra ke wh ich you sho uld have repa ired im
mediately by an authorized Audi dealer or
qualif ied workshop ¢
page 15.
(D Tips
-You can apply the pa rking br ake at any
time -even with the ignition switched
off. The ignition must be t urne d on and
the brake peda l must be pressed in order
to release the parking bra ke .
- Occas iona l noises when the parking
brake is applied and re leased are norma l
and are not a ca use for concern.
- When the vehicle is parked, the par king
brake goes through a se lf -test cycle at
regular intervals. Any assoc iated no ises
are norma l.
Parking
• Press the brake p eda l to stop the vehicle .
• Pull the switch @¢
page 79, fig. 92 to set
t h e parking br ake.
• Move the se lec tor lever to P .
• Turn the eng ine off
c:!> .,&_ .
• When on incl in es or declines, turn the steer
i ng whee l so that th e vehicle will roll into
the curb if it begins to move.
A WARNING
- Whe n you leave your veh icle -even if on
ly b rief ly -always remove the ig nition
key . This applies part icu larly when chil
dre n remain in t he ve hicl e. Otherwise the
c hildren co ul d st art the engine, re lease
the parking br ake or oper ate e lectri ca l eq
uipment (e.g. power windows). The re
is the risk of an acc ident.
- When the ve hicle is locked, no one -par
ticularly not children should rema in in
the vehicle . Locked doors make it more
difficult for emergency wo rkers to get i n
to the vehicle -putting lives at risk .
Starting from rest
The starting assist function ensures that the
parking brake is released au toma tically upon
starting .
Stopping and applying parking brake
• Pull the switch @¢ page 79, fig. 92 to ap-
p ly the parking bra ke .
Starting and automatically releasing the
parking brake
• W hen you sta rt to drive as us ual , the park
ing brake is a utomat ica lly released and yo ur
veh icle beg ins to move.
When stopping at a traffic signal or stopping in city traffic on vehicles with an a utomatic
transmission, the parking b rake can be ap
plied. The vehicle does not have to be held
with the foo tbrake . The parking brake elimi
nates the tendency to creep w ith a dr ive range
engaged. As soon as you d rive off as us ual ,
the pa rking bra ke is re leased automat ically
and t he vehicle s tarts to move.
Starting on slopes
When starting on inclines, the sta rting assist
prevents the vehicle from u ninten tionally roll
i ng back. The brak ing force of th e parki ng
brake is not re leased unti l su ffi cient d riving
f orce has been built up a t the w heels.
(D Tips
Fo r safety reasons, the pa rking brake is re
l eased a utom atically o nly when t he d riv
e r's s afety bel t is eng aged in the buckle.
Cruise control
Switching on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph
(30 km/h).
0
f
~
0
Fig . 94 Contro l lever with push-bu tton
Fig . 95 D isplay: Selected speed
.,. Pull the lever to position (!)~ fig. 94 to
swit ch the system on .
.,. Drive at the speed to be controlled.
.,. Press button @ to set that speed .
The stored speed and the green symbol
.,
;1; 9 a: .,
"'
II (US model)/ ... (Canadian mode l) are
shown in the display~
fig. 95. The display
may vary, depending on the type of display in
your vehicle.
The speed is kept constant by modifying en gine power or through an active brake inter
vention.
A WARNING
- Always pay attention to the traffic around you when the cruise control is in
operation . You are always responsib le for
your speed and the distance between
your vehicle and other vehicles.
On the road 83
-For reasons of safety, cruise control
should not be used in the city, in stop
and-go traffic, on twisting roads and
when road conditions are poor (such as ice, fog, gravel, heavy rain and hydro
plan ing) - risk of accident .
- Turn off the cruise control temporarily when enter ing turn lanes, highway exit
lanes or in construction zones.
- Please note that inadvertently ''resting"
your foot on the accelerator pedal causes
the cruise control not to brake. This is
because the cruise control is overridden
by the driver's acceleration.
- If a brake system malfunction such as
overheating occurs when the cruise con
trol system is switched on, the braking
function in the system may be switched off . The other cruise contro l functions re
main active as long as the indicator light
Ill (US models) !l'I (Canadian models)
is on.
(D Tips
The brake lights illuminate as soon as the
brakes app ly automatically .
Changing speed
.,. To increase/decrease the speed in incre
ments, tap the lever in the
0 10 direction
~ page 83, fig. 94 .
.,. To increase/decrease the speed quickly, hold
the lever in the
010 direction until the de
sired speed is displayed .
You can also press the accelerator pedal down
to increase your speed, e.g. if you want to pass someone. The speed you saved earlier
will resume as soon as you let off of the acce l
erator pedal.
If, however , you exceed yo ur saved speed by
6 mph (10 km/h) for longer than S minutes,
the cru ise control will be turned off tempora
rily. The green symbol in the display turns
white. The saved speed remains the same.
Transmission multitronic, S tronic,
tiptronic
Introduction
Appl ies to vehicles: with multitronic/5 tronic/tiptronic
The automatic transmission is controlled elec
tronically. The transmission upshifts or down
shifts automatically depending on which drive
program is se lected.
When a
moderate driving style is used, the
transmission se lects the most economica l
driving mode.
It wi ll then change up early and
de lay the downshifts to give better fuel econ
omy.
The transmission switches to a sporty mode after a kick -down or when the driver uses a
sporty driving style characteri zed by quick ac
celerator pedal movements, heavy accelera
tion, frequent changes in speed and traveling
at the maximum speed.
If desired, the driver can also se lect the gears
manually (tiptronic mode) q page 85.
Various a utomatic transmissions may be in
stalled, depending on the mode l:
multitronic transmission
The multitronic transmission is a continuously
variab le transmission. Power is trans ferred us
ing a mu ltidisk clutch. In contrast to conven
tional automatic transmissions using shifting
operations, the transmission ratio in the con
t inuously variab le transm iss ion is changed
continuously. This opt imizes the comfort level
and conserves fuel.
S tronic transmission
The 5 tronic is a dual-clutch transmission.
Power is transferred using two clutches that
work independently from one another. They
replace the torque converter used in conven
tional automat ic transmissions and allow the
ve hicle to accelerate without a noticeable in
terruption in traction .
Transmission 85
tiptronic transmission
In the tiptronic transm ission , power is trans
f erred by a torque converter.
Selector lever positions
Applies to vehicles: wit h mult itronic/5 tronic/tiptronic
1- -...~~------------,,--~ -... N
N
N
"" :ll
Fig . 96 D isp lay in t he inst rum ent cluster: se lec to r lever
in pos it io n P
The selector lever position engaged appears
next to the se lector lever as well as in the in
strument cluster display.
P -Park
In this se lector lever position the transmis
sion is mechanica lly locked. Engage P on ly
when the vehicle is
completely stopped q .&.
in Driving the automatic transmission on
page 88.
To shift in or out of position P, you must first
press and hold the brake pedal and then press
the re lease button in the selector lever handle
while moving the selector lever to or from P.
You can shift out of th is position only with the
ignition on .
R • Reverse
Select R only when the vehicle is at a full stop
and the engine is running at idle speed q &. in
Driving the automatic transmission on
page 88.
Before you move the se lector lever to R, press
both the release button in the hand le of the
selector lever
and the brake pedal at the same
time .
When the ignition is on, th e backup lights illu
minate when the selector lever is moved into
R.
The Automatic Shift Lock only functions when
the vehicle is statio nary or at speeds below
1 mph (2 km/h).
At speeds above about 1 mph (2 km/h) the
Automatic Shift Lock is automatically deacti
vated in the
N position.
A time de lay element prevents the se lector
l ever from locking when it is moved thro ugh
the N position (going from R to D/S). The lock
ing e lement will lock the selector lever if the
l ever is left in N (Neutral) for more than ap
prox imately 2 seconds, w ithout the brake ped
al being pressed.
R elease button
The release bu tton on the selec tor lever pre
vents the leve r from being accidenta lly shifted
into certain positions. Depend ing on the direc
tion of the shift, the se lector lever locks at d if
ferent positions. The positions are h ighlighted
i n the illustration ¢
fig. 97 .
Ignition key s afety interl ock
The key cannot be removed from the ignition un less the se lector lever is in the P park posi
tion . When the ign ition key is removed, the
selector lever will be locked in the P pos ition.
Driving the automatic transmission
App lies to vehicles: with mu ltitron ic/S tronic/t iptronic
F ig. 98 Shi ft gat e on th e center co nso le: se lec tor lever
wit h release b utto n
Starting the engine
"' The selector lever must be in P o r
N.
Starting off
"' Press and ho ld the brake pedal. Tran
sm iss ion 87
"' Press and hold the re lease button in these
lector lever hand le, select the desired selec
to r lever posit ion such as D/S and re lease
the button.
"' Wait briefly unt il the transmission has shift
ed (you w ill fee l a slight movement) .
"' Remove your foot from the brake pedal and
accelerate .
Stopping temporarily "' Keep the veh icle stationary using the brak
ing pedal, for example at traffic lig hts.
"' Do not press the accelerator peda l when do
ing this .
"' To prevent the vehicle from ro lling when you
s tart dr iv ing, set the parki ng b ra ke when
s topping on steep in clines ~,&. .
"' The parking brake will release a utomat ica lly
and the vehicle will start moving once you
press the acce lerator pedal.
Stopping/parking
I f the se lector lever is not in the P position
when you open the d river 's door, the ve hicle
could roll . The message Transmission : Car
may roll! Shift to park! appears.
"' Press and hold the bra ke peda l un til the ve -
hicle has come to a complete stop.
"' App ly the parking brake ~
page 80, Parking.
"'Select the P selector lever position ¢ ,&..
Stopping on an incline
"'Always press the brake pedal to ho ld the ve
hicle in pla ce and p revent it from " ro lli ng
b ack" ~,&. . Do not try to p reven t the veh i
cle from "rolling back" when a gear is en
gaged by increasing the engine speed
~ 0.
Starting on an incline
"' Ac tiva te the pa rk ing brake.
"' With the d riv in g gear sele cted, p ress the ac
celerator peda l carefully . The parking bra ke
w ill release automa tically if your seat be lt is
fastened .
U nder cert ain circ umstan ces, su ch as driving
in the mou nta ins, it may be usef ul to sw itch
temporarily to the man ual shift program in .,..
90 Transmi ssion
when there is n o possibility of over-rev
ving the e ngine.
- When the kick-down comes on, the
transmission will sh ift down to a lower
gear, depending on vehicle and engine
speeds.
- Tiptronic is inoperative when the trans
mission is in the fail-sa fe mode.
Kick-down
Applies to vehicles: with multitronic/5 tronic/t iptronic
Kick-down enables maximum acceleration .
Applies to vehicles with a multitronic
transmission
When you depress the acce le ra to r pedal be
yond the resis tance point, the transmission
downshifts into a lower gear ratio depending
on the vehicle speed and engine speed. As l ong as the accelerator peda l is depressed, the
engine speed is automat ica lly regula ted for
maximum acceleration .
Applies to vehicle s with a S tronic- /
tiptronic transmis sion
When you depress the accelerator pedal be
yond the resistance po int , the automat ic
tra nsmission downshifts into a lower gear, de
pending on vehicle speed and engine speed .
The upshift in to the next higher gea r takes
p lace once the maxim um specified eng ine
speed is reache d.
_& WARNING
Please note that the d rive wheels can spin
if kick-down is used on a smooth slippery
road -there is a risk of skidding .
Launch Control Program
Applies to vehicles: with S tron ic
T he Launch Control Program provides the
best acceleration possible when starting from
a stop.
Requirement: The engine must be at operat
ing temperature and the stee ring wheel must
not be turned. ..
Press the
I~ O FF ! button c;, page 181 whi le
the engine is running. The
II i ndicator light
illuminates in the instrument cl uster and
Stab ilizat ion control (ESC): Sport. Warn
ing! Restricted stability
appears in the driv
er info rmation system display .
.. Move the selector lever to the D/S posi tion
t o select sport mode (S) o r se lect the
dy
namic dr iving mode in dr ive se lect*
c:> page 107.
.. Press the brake pe dal s trongly with yo ur left
foo t and hold it down fo r at leas t 1 second .
.. At the same time, press the acce lerator ped
al down completely with your right foot un
til the eng ine reaches and maintai ns a high
RPM.
.. Remove your foot from the brake pedal
w ith in S seco nds
c;, &, .
_& WARNING
-Always ad apt your dr iving to the traffic
f low.
- On ly use the Launch Cont ro l Program
when road and traff ic conditions allow it
a nd other d river s w il l no t be en dangered
or annoyed by your driving and the vehi
cle's acceleration.
- Ple ase no te th at th e driving wheels can
spin an d the vehicle can break away
when sport mode is switc hed on, espe
cially when the road is slippe ry .
- Once you have accelerate d, you sho uld
sw itch sport mode off by pressing the
I~ O FF ! button.
(D Tips
- The transmission temperature may in
crease significa ntly after using the
Launch Control P rogram . If that hap
pens, the prog ram may not be availab le
for a few minutes. It will be ava ilable
again after a cool-down period.
- When accelerating using the Launch Cont rol program, all vehicle parts are
subject to heavy loads . Th is can result in
increased wear.
Transmission malfunction
Applies to vehicles: with multitronic/S tronic/tiptronic
[i1 Transmis sion: Pr ess brake p edal and se
lect gear again .
Press the brake pedal and se lect the des ired
selector lever position aga in . You can then
con tinue dr iv ing .
[i1 Transmi ssion overheating : Please drive
conserv ati vely.
The transmission temperature has increased
sign ificantly due to the sporty dr iving manner .
Drive in a less spo rty manner unt il the tem
perature returns to the no rma l range and the
indicator light switches of .
[i1 Transmission mal funct ion: You can con
tinue driving
T here is a system ma lfunction in the transmis
sion . You may continue driving . Drive to your
authorized Audi dealer or qualified repair fa
cility soon to have the malfunction corrected.
[i1 Transmis sion malfunction: Limited driv
ing funct ionality
There is a sys tem ma lfunction in the transmis
sion . The transmission is sw itch ing to emer
gency mode . This mode only shifts into cer
tain gears or will no longer shift at a ll. The en
g ine may stall. Drive to your authorized A udi
dea ler o r qualified repair facility immediately
to have the malf unction co rrected .
[i11:1 Transmission malfunct ion: No reverse
You can continue d riving
S tron ic transm ission: There is a system ma l
function in the transmission. T he transmis
sion is switch ing to emergency mode. This
mode on ly shifts into certain gears or will no
longer shift at all. The engine may sta ll. You
cannot engage the reverse gear . Drive to your
author ized Audi d ealer or qualifi ed repair fa
cili ty immed ia tely to have the ma lfunction
c o rre cted.
[i1 Transmi ssion malfunction: Stop vehicle
and shift to park . Transm
ission 91
Do not continue driving. Se lect the P selector
lever posit ion and see your authorized A udi
dealer or qualified repair facility for assis
tance.
(D Note
If t h e transmission switches to emergency
mode, you should ta ke t he ve hicle to an
a uthorized Audi dea lership as soon as pos
s ible to have the condition c orrected .
Selector lever emergency release
Applies to vehicles: with multitronic/S tronic/tiptronic
If the vehicle's power supply fails, the selec
tor lever can be released in an emergency.
Fi g. 101 Fr ont center co nso le : Remov ing t he as htray
in sert
F ig. 1 02 Selector lev er emer gency re le ase
"" To access the emergency re lease mecha
nism, remove the ashtray insert @ using the
release sw itch @
c:::> fig. 101.
"" Loosen and remove the cap in the ashtray
mount.
"" You now have access to a p in . Using a screw
driver or sim ilar ob ject, press the p in down
and hold it i n that position c:::>fig . 102.
"" Now pres s th e re lease but ton and move the
selec tor lever to the N pos it io n. ..,.