2014 AUDI A5 CABRIOLET ECO mode

88 Transmission
order to adjust the gears to the driving condi­
tions by hand
¢page 89.
On slopes, activate the parking brake first and
then move the selector lever to the P position.
This prevents too much stress from being placed on the locking mechanism.
Vehicles with multitronic transmission : Your
vehicle is equipped with
hill hold assist allow­
ing you to start while on an incline. The sys­
tem is activated when the brake pedal is pressed down and held
for a few seconds. The
br ake pre ssure will hold for
a moment after
the brake pedal loosens to preven t the vehicle
from rolling backwards while starting up.
A WARNING
- The vehicle can also roll when the engine
is stopped .
- Unintended vehicle movement can cause serious injury .
- Never leave your vehicle with the engine
running while in gear . If you must leave
your vehicle when the engine is running,
activate the parking brake and move the
selector lever to P.
- Power is still transmitted to the wheels
when the engine is running at idle. To
prevent the vehicle from "creeping", you
must keep your foot on the brake when
the engine is running and the selector
lever is in D/S or R or "tiptronic" mode is
selected.
- Do not press the accelerator pedal when
changing the selector lever position
while the vehicle is stationary and the
engine is running.
- Never shift into R or P while driving.
- Before driving down a steep slope, re-
duce your speed and shift into a lower
gear with "tiptronic".
- Do not ride the brakes or press the brake
pedal too often or too long when driving
down a hill . Constant braking causes the
brakes to overheat and substantially re­
duces braking performance, increases
braking distance or causes complete fail­
ure of the brake system. -
To prevent the vehicle from rolling back
when stopping on inclines, always hold it
in place with the brake pedal or parking
brake .
- Never hold the vehicle on an incline with
a slipping clutch. The clutch opens auto­
matically when it becomes too hot from
the overload . An indicator lamp
mJ illu­
minates and a driver message appears
¢ page 91 when the clutch is overload­
ed.
- If the engine must remain running, never
have any driving position engaged when
checking under the hood. Make sure the
selector lever has securely engaged and
is locked in P with the parking brake set
¢ page 206. Otherwise, any increase in
engine speed may set the vehicle in mo­
tion, even with the parking brake ap­
plied .
(D Note
-S tronic- and tiptronic transmission :
When stopping on an incline, do not try
to hold the vehicle in place by pressing the accelerator pedal while a driving gear
is selected . This can cause the transmis­
sion to overheat and can damage it. Acti­
vate the parking brake or press the brake pedal to prevent the vehicle from rolling .
- S tronic- and tiptronic transmission : Al­
lowing the vehicle to roll when the en­
gine is stopped and the selector lever is
in N will damage the transmission be­
cause it is not lubricated under those cir­
cumstances.
(D Tips
For safety reasons, the parking brake is re­
leased automatically only when the driv­
er's safety belt is engaged in the buckle.

90 Transmi ssion
when there is n o possibility of over-rev ­
ving the e ngine.
- When the kick-down comes on, the
transmission will sh ift down to a lower
gear, depending on vehicle and engine
speeds.
- Tiptronic is inoperative when the trans ­
mission is in the fail-sa fe mode.
Kick-down
Applies to vehicles: with multitronic/5 tronic/t iptronic
Kick-down enables maximum acceleration .
Applies to vehicles with a multitronic
transmission
When you depress the acce le ra to r pedal be­
yond the resis tance point, the transmission
downshifts into a lower gear ratio depending
on the vehicle speed and engine speed. As l ong as the accelerator peda l is depressed, the
engine speed is automat ica lly regula ted for
maximum acceleration .
Applies to vehicle s with a S tronic- /
tiptronic transmis sion
When you depress the accelerator pedal be­
yond the resistance po int , the automat ic
tra nsmission downshifts into a lower gear, de­
pending on vehicle speed and engine speed .
The upshift in to the next higher gea r takes
p lace once the maxim um specified eng ine
speed is reache d.
_& WARNING
Please note that the d rive wheels can spin
if kick-down is used on a smooth slippery
road -there is a risk of skidding .
Launch Control Program
Applies to vehicles: with S tron ic
T he Launch Control Program provides the
best acceleration possible when starting from
a stop.
Requirement: The engine must be at operat ­
ing temperature and the stee ring wheel must
not be turned. ..
Press the
I~ O FF ! button c;, page 181 whi le
the engine is running. The
II i ndicator light
illuminates in the instrument cl uster and
Stab ilizat ion control (ESC): Sport. Warn ­
ing! Restricted stability
appears in the driv­
er info rmation system display .
.. Move the selector lever to the D/S posi tion
t o select sport mode (S) o r se lect the
dy­
namic dr iving mode in dr ive se lect*
c:> page 107.
.. Press the brake pe dal s trongly with yo ur left
foo t and hold it down fo r at leas t 1 second .
.. At the same time, press the acce lerator ped­
al down completely with your right foot un ­
til the eng ine reaches and maintai ns a high
RPM.
.. Remove your foot from the brake pedal
w ith in S seco nds
c;, &, .
_& WARNING
-Always ad apt your dr iving to the traffic
f low.
- On ly use the Launch Cont ro l Program
when road and traff ic conditions allow it
a nd other d river s w il l no t be en dangered
or annoyed by your driving and the vehi ­
cle's acceleration.
- Ple ase no te th at th e driving wheels can
spin an d the vehicle can break away
when sport mode is switc hed on, espe­
cially when the road is slippe ry .
- Once you have accelerate d, you sho uld
sw itch sport mode off by pressing the
I~ O FF ! button.
(D Tips
- The transmission temperature may in ­
crease significa ntly after using the
Launch Control P rogram . If that hap­
pens, the prog ram may not be availab le
for a few minutes. It will be ava ilable
again after a cool-down period.
- When accelerating using the Launch Cont rol program, all vehicle parts are
subject to heavy loads . Th is can result in
increased wear.

106 Audi drive select
Audi drive select
Driving settings
Introduction
App lies to vehicles: with Audi drive select
Drive select provides the possib ility to exper i­
e nce diffe ren t types of vehi cle sett ings in o ne
ve hicl e. For ins tance, us ing t he three
Com­
fort , Auto and Dynamic modes, the driver can
switch from a sporty to a comfortab le drivi ng
mode with the press of a b utton.
A ddit ionally, in veh icles wi th MM I*, the vehi ­
cle setup for
Individual* mode can be c us­
tom ized by you. This makes it possib le to
comb ine settings such as a sporty engine tun ­
ing with comfortable steering.
A WARNING
Improper use of the A udi drive select can
cause collisions , ot her acc idents and se ri­
ous pe rsonal injury.
Description
App lies to vehicles: with Audi drive select
The vehicle setup in each mode depends on
the veh icle's features . However, the engin e,
automa tic t ransmissio n and s teeri ng a re a l­
ways involved.
-
Engine and automatic transmission
Depending on the mode , the e ng ine and the
automatic t ransm ission respond quicke r or i n
a more ba la nced manne r to a cce le rator pedal
move ments. In t he sporty dynam ic mode, the
a ut om at ic t ra nsmissio n shifts at h igher R PMs.
Steering
The steering adapts in terms of stee ring effort
and steering ra tios . Ind irect steer ing that
moves easi ly, l ike the stee rin g in comfort
mode, is best su ite d t o long dr ive s on a high­
way. In co ntr ast, dynam ic mo de p rov ides
sporty, direct steering .
T he fo llow ing applies to vehicles with dynam ic
steer ing*: the stee ring ratio changes based on
ve hicl e spee d in order to maint ain op timum steering effort
for the drive r at all times . This
sets the stee ring to be less sens itive at higher
speeds in order to provide improved vehicle
control. At reduced speeds, however, steer ing
is more d irect in order to keep the steering ef­
fort as minima l as poss ible when the driver is
mane uveri ng the veh icle. At low and ave rage
speeds, dynamic steering addit iona lly pro­
vides more respon sive stee rin g pe rforma nce.
Adaptive dampers*
The adaptive dampers* use se nsors to record
informa tion regard ing steer ing movemen ts,
braking and acceleration o perations by the
drive r, road surfac e, d riv in g speed, and load.
T his makes it poss ible to adapt damp ing to
the driving si tua tion v irtu ally in real t ime.
Dr ive sele ct also makes i t possib le to sa tisfy
t h e desire fo r spo rty suspension ( Dynamic)
and comfortab le suspension (Comfort) with ­
o ut giving up ba lanced tuning (Auto) .
Sport differential*
As a component o f the all whee l dr ive sys tem
(quat tro)
~ page 184, t he spo rt differential *
dist ributes t he driving power to the rear ax le
depen ding on the sit uat io n. The distrib ution
of power var ies depending on the mode se­
lected. The goal is a high level of agility and
ability to accelerate on curves. T he ve hicle is
very res pons ive to stee ring .
Audi adaptive crui se control*
The behav ior when accelerating can be adjust­
ed from comf ortab le to sporty, depending on
t h e drive select mode. Adaptive cr uise control
also responds to the driv ing behavior of the
vehicle ahead in a mo re conservative o r spo rty
manner .
Engine sound*
The sound of the eng ine is adapted to these­
lected mode and ranges from subtle to sporty.
(!) Tips
- In s ome models, the maximum vehicle
spee d can only be reached in the
Auto
and Dynamic modes.

Parking system (rear,
with rear view camera)
Introduction
Applies to vehicles: with parking system (rear, with rear
view camera)
Fig. 121 Parking mode 1: reverse parking
Fig. 122 Parking mode 2: parallel pa rk in g
Vehicles with the parking system are equipped
with a
rear view camera in addition to the
acoustic parking system.
You can choose between two modes to assist
you with parking. For example, you can use "parking mode
l" when parking in a parking
space or garage
q fig. 121. When you want to
park parallel to the edge of the street, select
"parking mode 2"
qfig. 122.
The rear acoustic park assist system is inte­
grated in the rear of the vehicle and the rear
view camera is integrated in the rear lid
qpage 112.
A WARNING
-The rear view camera has blind spots, in
wh ich objects cannot be detected. Be es­
pecially careful to check for small chil­
dren and animals before backing up.
Small chi ldren and anima ls will not al­
ways be detected by the sensors .
Park assist 111
General Information
Applies to vehicles: with parking system (rear, with rear
view camera)
Fig. 123 Covered area (!) and u ncove red area @of the
r ear v iew came ra
Fig. 124 Tru nk l id : Locat ion of the rear view came ra
Sen so rs in the bumper
Sensors are located in the rear bumpers. If
these detect an obstacle, audible signals warn
you. The range at which the sensors begin to
measure is approximately:
To the side
2 ft (0.60 m)
Center rear 5 .2 ft (l.60 m)
Distance warning when reversing starts when
an obstacle is detected in the range of the
parking assist system . As the distance de ­
creases, the time interval between the audible
tones becomes shorter .
When the distance is less than 1ft (0.30 m),
the tone becomes continuous. At th is point
you should stop backing up .
If the distance to an obstacle stays the same,
the volume of the distance signa l chime is
gradually reduced after about 4 seconds (does ..,..

Switching off
• Drive faster than 9 mph (15 km/h), or
• take the vehicle out of reverse gear. The
acoustic parking system is immediately de­
activated, and the rear view camera picture is deactivated automatically after a period
of about 15 seconds, or
• switch off the ignition.
The delay in deactivating the camera provides
an uninterrupted view behind the vehicle es­
pecially when maneuvering in tight parking
spaces and prevents the picture from turning
off the every time you sh ift out of reverse .
If the warning message appears in the display but not the rear view camera picture, read and
confirm the warning message . The acoustic
d istance signal is always active.
If you press a function button on the MMI
control console, the rear view camera picture
disappears . The rear view camera picture reap­
pears the next time you park.
Further information on the warning message
and the MMI control console can be found in
the MMI instruction booklet.
A WARNING
- Only use the rearview camera to assist
you if it shows a good, clear picture. For
example, the image may be affected by
the sun shining into the lens, dirt on the
lens or if there is a defect.
- Use the rearview camera only with the
rear lid completely closed. Make sure any
objects you may have mounted on the
rear lid do not block the rearview cam­
era.
(D Tips
- The rear v iew camera picture is available
as soon as the MMI Display or the MMI is
switched on, or the start-up phase is
completed.
- The sensors must be kept clean and free
of snow and ice for the park assist to op­
erate.
Park assist 113
- You can change the vo lume and pitch of
the signals as we ll as the disp lay
~page 115.
-What appears in the display is time-de­
layed.
Reverse Parking
App lies to vehicles: wit h parking system (rear, with rear
v iew camera}
Parking mode 1 can be used when parking in
a garage or parking space.
Fig. 125 MMI Display: Aim ing at a park ing spot
Fig. 1 26 MMI Disp lay : Al ign ing the veh icle
• Switch the MMI on and select the reverse
gea r.
• Turn the steering wheel until the orange ori­
entation lines (!) appear in the parking spot
i=> fig. 125. Use the markings @to help you
estimate the distance from an obstacle.
Each marking corresponds to 3 ft (1 m). The
blue area represents an extens ion of the ve­
hicle's outline by approximately 16 ft (5 m)
to the rear.
• Wh ile driving in reverse gear, adjust the
steer ing whee l angle to fit the parking space
with the aid of the orange orientation lines
i::>0 .@ marks the rear bumper. You should
stop driving in reve rse as soon as and no
Ill>-

Homelink
Universal remote
control
Description
Applies to vehicles: with Home link
The HomeLink universal remote control can
be programmed with the remote control for
devices that are already present.
With Home Link, you can control devices such
as the garage door, security systems, house
lights , etc. comfortably from the inside of you
vehicle.
Homelink makes it possible for you to rep lace
three different remote controls from dev ices
in your home with one universal remote. Th is
feature works for most garage door and exte­
rior door motor signals. Programming the in­
dividual remote control for your remote con ­
trol takes place near the center of the radiator
grille. There is a control module attached at
this location .
A one-time programming of the sensor must be performed before you are able to use sys­
tems with Homelink. If the system does not activate after performing the one-time pro­
gramming, check whether the system uses a rolling code¢
page 120 for vehicles without
the
MMI*.
& WARNING
-
- Never use the Homelink transmitter
with any garage door opener that does
have not the safety stop and reverse fea­
ture as requ ired by federa l safety stand­
ards. Th is includes any garage door open­
er mode l manufactured before April 1,
1982.
-A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety standards . Using a garage door
opener without these features increases
risk of serious injury or death.
Homelink 11 7
-For safety reasons never re lease the
parking brake or start the engine while
anyone is standing in front of the vehicle .
- A garage door or an estate gate may
sometimes be set in motion when the
Homelink remote control is being pro­
grammed. If the device is repeatedly ac­
tivated, th is can overstrain motor and
damage its electrical components - an
overheated mo to r i s a fire haza rd!
- To avoid possib le injuries or property
damage, please always make abso lutely
certa in that no persons or objects are lo­
cated in the range of motion of any
equipment being operated.
(0 Tips
- If you would like more information on
Homelink, where to purchase the Home­
Link compat ible products, or would like
to purchase the Home Link Home Light­
ing Package, please call toll-free :
1-800-355-3515.
-For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions ¢
page 267.
-For security reasons, we recommend that
you clear the programmed b uttons be­
fore selling the vehicle.
Operation
App lies to vehicles : with Homeli nk
Fig. 129 H ead li ner: controls
Req uirement: The buttons must be program-
med
c!) page 118 or ¢ page 119. ..,_

118 Homelink
• To open the garage door, press the p rogram­
med button . The LED @will light up or
flash.
• To close the garage door, pre ss the button
again.
@ Tips
To open the garage door, press the button, but do not press it for longer ten seconds
or the Homelink module will switch to
programming mode.
Programming the transmitter (version A)
Appl ies to vehicles: with Home link and MMI
Fig. 130 Dista nce between t he ra d iato r grille and t he
hand tran sm itter
You can p rogram the fixed code and ro lling
code systems using the descr ibed procedure.
Programming the button
• Turn the ign ition on .
• The re a re two ways to program the button :
P res s the but ton
¢ page 117, fig. 129 tha t
you wou ld like to p rogram. Use the instruc­
tions that appear in the MM I* to pe rform
the p rogramming. Or
• Se lect : ICAR ifunct ion button>
Car sy stems*
con trol but ton > Vehicle sett ing s> Garage
door opener
> Program garage door open·
er .
If this path is not ava ilable, program
Homelink as desc ribed in vers ion B
.;, page 119.
• Se lect t he button t hat yo u wo uld like to p ro­
gram.
• Fo llow the ins tructions in the MMI* .
• If the garage door open ing must also be
synchronized w it h the Homel ink modu le, refer to the owner
's manua l for the garage
door opener .
Remote con tro l unit s fo r garage door ope ne rs
in Canada are se t to stop t ransmi tting radio
frequency signa ls afte r two seconds . This time
may not be sufficient for the Homelink sys ­
tem to learn the radio frequency signa l. Per­
form all other steps as described above.
Erasing /Clearing the programmed button
s etting s
• To erase all of the programmed buttons at
the same time, select : ICAR !function b utton
> Car Systems * control butto n > Vehicle set·
tings
> Garag e door opener > Clear pro·
gram setting s> Yes .
The prog rammed but­
tons can not be erased individua lly. Repro­
gram the buttons if ne cess ary.
• Reprogr am an individua l bu tton in the same
manner that you wou ld for the one-time
programming .
Displaying the version /status /country
code
• Sele ct: !CAR I function bu tton > Car sy stem s*
contro l but to n > Vehicle settings > Garage
door opener
> Version information .
(D Tips
- Programming throug h the MMI* is not
possible with all infotainment systems.
If this is the case , program Homelink as
descr ibed in version B
c:) page 119.
-The required distance betwee n the hand
transm itter and the Homelink module in
the radiator gr ille¢
fig. 130 depends on
the system that you are prog ramming .
- Depending on the mode l of the garage
door opener, you may need to release the
butto n on the remote and press it again
w hen programming. When program ·
m ing a new device, keep the butto n
presse d for at least 15 seconds before
t ry ing ag ain w ith the transmit ter in a dif­
fere nt posi tion. W atch o ut for the emer­
gency flasher during tha t time.

Programming the transmitter (version B)
A pplies to vehicles: with Horne link
Fig. 131 Distance between the radiato r grille and the
hand transmitte r
Programming: phase 1 on the control unit
1. Switch on the ig nit ion (do not start the
engine) .
2. Press and hold both of the outer Home­
Link buttons
r=>page 117, fig. 129 until
the LED @ turns off completely (about
20
seconds). This procedure clears the stand­
ard codes that were set at the factory and
does
not need to be repeated again to
program the other buttons.
3. Briefly press the Homelink button that
you would like to program .
4 . Wait until the LED@ beg ins to blink
quickly. The Home Link modu le wi ll now
remain in learning mode for
5 minutes .
5. Now stand in front of your vehicle with
the original hand transmitter for the ga­ rage door opener or for the device that
you would like to allocate to the Home­
Link button.
Programming: phase 2 on the radiator
grille
6. Hold the original hand transmitter some­
what towards the center of your vehicle's radiator griller=>
fig. 131.
7. Now activate (press) the hand transmit­
ter.
8 . Pay attention to the turn signals for your
vehicle when activating the hand trans­
mitter. If th e emergency flashers blink
three times, the programming was suc­
cessful. If the emergency flasher only
blinks one time, the 5 minute time limit
Homelink 119
for the adaptation has expired or the pro­
gram ming was unsuccessful. Repeat the
programming from step 3 on the controls
or se lect another distance from the radia­
tor grille.
9. If the garage door or other devices still
fail to be activated w ith the Homelink
control buttons after programming is
completed, it is possible that these sys­
tems might be working with a rolling code
instead of the normal fixed code.
A Roll­
ing code programming must be per­
formed
r=> page 120 .
Program the remaining two buttons acc ord ing
to the instructions mentioned above . Begin
similarly with the 3rd step if the program­
ming connection was successful for the first
button.
Remote control units for garage door openers
in Canada are set to stop transmitting radio
frequency signa ls after two seconds. This time
may not be suffic ient for the Homelink sys­
tem to learn the radio frequency signal. Per­
form all other steps as described above.
Erasing the buttons
.,. Switch on the ignition (do not start the en­
gine).
.,. Press and hold both of the outer buttons un­
til the LED@ turns off completely (about
20 seconds) to erase all of the buttons si­
multaneously .
.,. Programmed buttons cannot be erased indi­
vidua lly. Reprogram the buttons if necessa­
ry.
Reprogramming the buttons
.,. Switch on the ignition (do not start the en­
gine).
.,. To reprogram an individua l button, press
and hold the button until the LED @ starts
to fla sh quickly (after about ten seconds).
Release the button immedia tely. The Home­
L ink module will now remain in learning
mode for 5 minutes.
.,. Continue with step 5.