2014 AUDI A5 CABRIOLET wheel

Starting off with a trailer
To prevent rolling back unintentionally on an
incline, do the following:
11-Keep the switch@¢ page 79, fig. 92 pulled
and depress the accelerator. The park ing
brake stays applied and prevents the vehicle
from roll ing backward.
11-You can release the switch @ once you are
su re that yo u are develop ing enough dr iv ing
f orce at the wheels by depress ing the accel­
erator.
D epending on the weight of the r ig (vehicle
and tra ile r) and the severi ty of the in cli ne, you
may roll backwards as you start. Yo u can pre­
vent rolling backwards by holding the parking brake switch @ pulled out and accelerating -
just as you would when starting on a hill with
a conventional hand brake.
Emergency braking
In the event that the conventional brake sys­tem fails or locks.
11-In an emergency, pull the switch @
¢
page 79, fig. 92 and contin ue to p ull it to
s low your vehicle down with the parking
brake.
11-As soon as you release the sw itch @ or ac-
ce lerate, the braking process stops .
If you pull the sw itch @ and ho ld it above a
speed of about 5 mph (8 km/h), the emergen­
cy braking function is in itiated. The vehicle is
braked at all four wheels by activating the hy­
draul ic brake system . T he b rake performance
i s simi lar to making an emergency stop ¢
.&,.
In order not to activate the emergency brak­
i ng by m istake, an audible warning tone (buz­
zer) sounds when the switch @ is pu lled. As
soon as the switch @ is released, o r th e accel­
e rator pedal is dep ressed , emergency bra king
stops.
WARNING
Emergency braking should on ly be used in
an eme rgency, when the normal foot brake
On th e ro ad 81
has failed or the brake pedal is obstructed.
Using the parking brake to perform emer­
gency brak ing will slow your vehicle down
as if you had made a full brake application .
The laws of physics cannot be suspended
even with ESC and its associated compo­
nents (ABS, ASR, EDS). In corners and
when road o r wea the r cond itions are b ad,
a full brake application can ca use the vehi­
cle to skid or the rear end to break away -
risking an accident .
Speed warning system
, Overview
The speed warning system helps you to keep
your driving speed below a set speed limit.
The speed warning system warns if the driver
exceeds a previous ly stored max imum speed.
A war ning tone w ill sound as soon as the vehi­
cle speed exceeds the set speed by about
3 mph (3 km/h) . At the same t ime, a warn ing
symbol appears in the display. The symbo l's
appearan ce might be different in some mod­
els.
The speed warn ing system has two warning
thresholds that funct ion i ndependent ly of
each othe r and that have somewhat different
purposes:
Speed w arning 1
You can use speed warning 1 to set the maxi­ mum speed while you are driving . This setting
will remain in effect until you turn off the ig ni­
tion, assumi ng that you have not changed or
rese t the set ting.
The . (USA models) /. (Canada models)
speed warning symbo l in the warning 1 dis­
play appears when you exceed the maximum
speed . It goes ou t when the speed falls be low
the stored maximum speed.
T he speed warn ing symbol w ill also go out if
the speed
exceeds t h e stored maximum speed
by more than about 25 mph (40 km/h) for at
least 10 seconds . The stored max imum speed
is de leted . ..,_

88 Transmission
order to adjust the gears to the driving condi­
tions by hand
¢page 89.
On slopes, activate the parking brake first and
then move the selector lever to the P position.
This prevents too much stress from being placed on the locking mechanism.
Vehicles with multitronic transmission : Your
vehicle is equipped with
hill hold assist allow­
ing you to start while on an incline. The sys­
tem is activated when the brake pedal is pressed down and held
for a few seconds. The
br ake pre ssure will hold for
a moment after
the brake pedal loosens to preven t the vehicle
from rolling backwards while starting up.
A WARNING
- The vehicle can also roll when the engine
is stopped .
- Unintended vehicle movement can cause serious injury .
- Never leave your vehicle with the engine
running while in gear . If you must leave
your vehicle when the engine is running,
activate the parking brake and move the
selector lever to P.
- Power is still transmitted to the wheels
when the engine is running at idle. To
prevent the vehicle from "creeping", you
must keep your foot on the brake when
the engine is running and the selector
lever is in D/S or R or "tiptronic" mode is
selected.
- Do not press the accelerator pedal when
changing the selector lever position
while the vehicle is stationary and the
engine is running.
- Never shift into R or P while driving.
- Before driving down a steep slope, re-
duce your speed and shift into a lower
gear with "tiptronic".
- Do not ride the brakes or press the brake
pedal too often or too long when driving
down a hill . Constant braking causes the
brakes to overheat and substantially re­
duces braking performance, increases
braking distance or causes complete fail­
ure of the brake system. -
To prevent the vehicle from rolling back
when stopping on inclines, always hold it
in place with the brake pedal or parking
brake .
- Never hold the vehicle on an incline with
a slipping clutch. The clutch opens auto­
matically when it becomes too hot from
the overload . An indicator lamp
mJ illu­
minates and a driver message appears
¢ page 91 when the clutch is overload­
ed.
- If the engine must remain running, never
have any driving position engaged when
checking under the hood. Make sure the
selector lever has securely engaged and
is locked in P with the parking brake set
¢ page 206. Otherwise, any increase in
engine speed may set the vehicle in mo­
tion, even with the parking brake ap­
plied .
(D Note
-S tronic- and tiptronic transmission :
When stopping on an incline, do not try
to hold the vehicle in place by pressing the accelerator pedal while a driving gear
is selected . This can cause the transmis­
sion to overheat and can damage it. Acti­
vate the parking brake or press the brake pedal to prevent the vehicle from rolling .
- S tronic- and tiptronic transmission : Al­
lowing the vehicle to roll when the en­
gine is stopped and the selector lever is
in N will damage the transmission be­
cause it is not lubricated under those cir­
cumstances.
(D Tips
For safety reasons, the parking brake is re­
leased automatically only when the driv­
er's safety belt is engaged in the buckle.

90 Transmi ssion
when there is n o possibility of over-rev ­
ving the e ngine.
- When the kick-down comes on, the
transmission will sh ift down to a lower
gear, depending on vehicle and engine
speeds.
- Tiptronic is inoperative when the trans ­
mission is in the fail-sa fe mode.
Kick-down
Applies to vehicles: with multitronic/5 tronic/t iptronic
Kick-down enables maximum acceleration .
Applies to vehicles with a multitronic
transmission
When you depress the acce le ra to r pedal be­
yond the resis tance point, the transmission
downshifts into a lower gear ratio depending
on the vehicle speed and engine speed. As l ong as the accelerator peda l is depressed, the
engine speed is automat ica lly regula ted for
maximum acceleration .
Applies to vehicle s with a S tronic- /
tiptronic transmis sion
When you depress the accelerator pedal be­
yond the resistance po int , the automat ic
tra nsmission downshifts into a lower gear, de­
pending on vehicle speed and engine speed .
The upshift in to the next higher gea r takes
p lace once the maxim um specified eng ine
speed is reache d.
_& WARNING
Please note that the d rive wheels can spin
if kick-down is used on a smooth slippery
road -there is a risk of skidding .
Launch Control Program
Applies to vehicles: with S tron ic
T he Launch Control Program provides the
best acceleration possible when starting from
a stop.
Requirement: The engine must be at operat ­
ing temperature and the stee ring wheel must
not be turned. ..
Press the
I~ O FF ! button c;, page 181 whi le
the engine is running. The
II i ndicator light
illuminates in the instrument cl uster and
Stab ilizat ion control (ESC): Sport. Warn ­
ing! Restricted stability
appears in the driv­
er info rmation system display .
.. Move the selector lever to the D/S posi tion
t o select sport mode (S) o r se lect the
dy­
namic dr iving mode in dr ive se lect*
c:> page 107.
.. Press the brake pe dal s trongly with yo ur left
foo t and hold it down fo r at leas t 1 second .
.. At the same time, press the acce lerator ped­
al down completely with your right foot un ­
til the eng ine reaches and maintai ns a high
RPM.
.. Remove your foot from the brake pedal
w ith in S seco nds
c;, &, .
_& WARNING
-Always ad apt your dr iving to the traffic
f low.
- On ly use the Launch Cont ro l Program
when road and traff ic conditions allow it
a nd other d river s w il l no t be en dangered
or annoyed by your driving and the vehi ­
cle's acceleration.
- Ple ase no te th at th e driving wheels can
spin an d the vehicle can break away
when sport mode is switc hed on, espe­
cially when the road is slippe ry .
- Once you have accelerate d, you sho uld
sw itch sport mode off by pressing the
I~ O FF ! button.
(D Tips
- The transmission temperature may in ­
crease significa ntly after using the
Launch Control P rogram . If that hap­
pens, the prog ram may not be availab le
for a few minutes. It will be ava ilable
again after a cool-down period.
- When accelerating using the Launch Cont rol program, all vehicle parts are
subject to heavy loads . Th is can result in
increased wear.

94 Audi adaptive cruise control and braking guard
confirmed by the video camera, an acute
collision warning.
- For safety reasons, do not use adaptive
cruise control when driving on roads with
many curves, when the road surface is in
poor condition and/or in bad weather
(such as ice, fog, gravel, heavy rain and
hydroplaning). Using the system under
these conditions could result in a colli­
sion.
- Switch adaptive cruise control off tempo­
rarily when driving in turning lanes, on
expressway exits or in construction
zones. This prevents the vehicle from ac­
celerating to the set speed when in these
situations.
- The adaptive cruise control system will
not brake by itself if you put your foot on
the accelerator pedal. Doing so can over­
ride the speed and distance regulation.
- When approaching stationary objects
such as stopped traffic, adaptive cruise
control will not respond and braking
guard will have limited function.
- The adaptive cruise control system and
braking guard do not react to people, an­
imals, objects crossing the road or on­
coming objects .
- The function of the radar sensor can be
affected by reflective objects such as
guard rails, the entrance to a tunnel,
heavy rain or ice.
- Never follow a vehicle so closely that you cannot stop your vehicle safely. The
adaptive cruise control cannot slow or
brake the vehicle safely when you follow
another vehicle too closely . Always re­
member that the automatic braking
function cannot bring the vehicle to a sudden or emergency stop under these
conditions.
- To prevent unintended operation, always
switch ACC off when it is not being used.
{[) Note
The sensor can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. That could affect the adaptive cruise control system and braking guard.
Have your authorized Audi dealer or au­
thorized Audi Service Facility check their
function.
, In curves
Applies to vehicles: wit h Aud i adapt ive cr uise contro l
Fig. 104 Example: driv ing into a curve
When driving into a curve <=> fig. 104 and out
of a curve, the adaptive cruise control may re­ act to a vehicle in the next lane and apply the
brakes. You can override or prevent the brak­
ing by pressing the accelerator pedal briefly.
Stationary objects
Applies to vehicles: with Aud i adaptive crui se contro l
Fig. 105 Example: object changing lanes a nd station ­
a ry object
The adaptive cruise control system only reacts
to objects that are moving or that the system
has already detected as moving. For example,
if a vehicle @, which has already been detect­
ed by the adaptive cruise control, turns or
changes lanes and another stationary vehicle
@ is located in front of that vehicle, the sys­
tem will not react to the stationary vehicle.

General information
Applies to vehicles: with Audi side assist
®
©
Fig . 116 Dr iving situations
Fig. 117 Rear of t he ve hicle: positio n of t he se nsors
., ... N 0 IL
l:l
Side assist functions at speeds above approx i­
mately 19 mph (30 km/h).
@ Vehicl es th at ar e approaching
In certain cases, a vehicle will be classified as
cr itical for a lane change even if it is still
somewhat far away. The fas ter a vehicle ap­
p roaches, the sooner the display in the exteri­
or m irror will t urn on.
@ Vehicles traveling with you
Vehicles traveling w ith you are indicated in the
exterior m irror if they are classified as cr itical
for a lane change. All vehicles detec ted by
side assist are indicated by the time they en­
ter your "blind spot", at the latest.
Audi side assist 103
@ Veh icle s left behind
If you s low ly pass a vehi cle that s ide assist has
detected (the difference in speed between the
vehicle and you r vehicle is less than 9 mph
(15 km/h)), the display in the exterior mirror
turns on as soon as the vehicle enters your blind spot.
T he disp lay will not t urn on if you quickly pass
a vehicle that side assist has detected (the dif­
ference in speed between the veh icle and your
vehicle is greater than 9 mph (15 km/h)).
Functional limitations
The radar senso rs are designed to detect the
left and right adjacent lanes when the road
lanes are the normal width. In certain situa­
tions, the disp lay in the exterior mirror may
turn on even though there is no vehicle locat­
ed in the area that is cr itical for a la ne change.
For example:
- if the lanes are narrow or if your are dr iving
on the edge of your lane.
If this is the case,
the system may have detected the vehicle in
another lane that is
not adjacent to your
current lane .
- if you a re driving through a curve. Side assist
may react to a vehicle that is one lane ove r
from the adjacent lane.
- if side assist reacts to other objects (such as
high or d isp laced guard rails) .
- In poor weather conditions. The side assist
functions are l imited .
Do not cover the radar sensors <=>
fig. 117 with
stickers, depos its, bicycle wheels or other ob­
jects, because this will affect the funct ion. Do
not use s ide ass ist when towing a trailer. For
i nformation on cleaning, refer to<=>
page 195.
_&. WARNING
- Always pay attention to traffic and to t he
area a round your ve hicl e. S ide assist can­
not repla ce a driver's attention. T he driv­
er a lone is always responsible for lane
changes and similar driving mane uvers.

104 Audi side assist
-Improper reliance on the side assist sys­
tem can cause collisions and serious
personal injury:
- Never rely only on side assist when
changing lanes.
- Always check rear view mirrors to make
sure that it is safe to change lanes.
- Side assist cannot detect all vehicles un­
der all conditions- danger of accident!
- Please note that side assist indicates
there are approaching vehicles, or
vehicles in your blind spot, only after
your vehicle has reached a driving speed
of at least 19 mph (30 km/h).
- In certain situations, the system may not
function or its function may be limited.
For example:
- if vehicles are approaching or being left
behind very quickly . The display may
not turn on in time.
- in poor weather conditions such as
heavy rain, snow or heavy mist .
- on very wide lanes, in tight curves or if
there is a rise in the road surface.
Vehicles in the adjacent lane may not
be detected because they are outside
of the sensor range.
(D Note
The sensors can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. This can affect the system.
Have your authorized Audi dealer or au­
thorized Audi Service Facility check their
function.
@ Tips
- If the window glass in the driver's door
or front passenger's door has been tint­
ed, the display in the exterior mirror may
be misinterpreted.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions¢
page 267.
Activating and deactivating
A pp lies to vehic les : wi th Audi s ide ass ist
Fig. 118 Driver's door: Side ass ist butto n
.. Press the button c> A in General informa­
tion on page 103
to switch the system on/
off. The LED in the button turns on when
side assist is switched on .
Adjusting the display brightness
Applies to vehicles: wit h Audi side ass ist
The signal brightness con be set in the radio
or MM!*.
.. Select: I CAR I function button > Audi side as­
sist.
.. Select: !CARI function button> Car systems*
control button > Driver assist> Audi side
assist .
The display brightness adjusts automatically
to the brightness of the surroundings, both in
the information and in the warning stage . In
very dark or very bright surroundings, the dis­ play is already set to the minimum or maxi­
mum level by the automatic adjustment. In
such cases, you may notice no change when
adjusting the brightness, or the change may
only be noticeable once the surroundings
change.
Adjust the brightness to a level where the dis­
play in the information stage will not disrupt
your view forward. If you change the bright­
ness, the display in the exterior mirror will
briefly show the brightness level in the infor­
mation stage. The brightness of the warning
stage is linked to the brightness in the infor ­
mation stage and is adjusted along with the
information stage adjustment.

@ Tips
-Side assist is not active whi le you are
making the adjustment.
- Your settings are automatica lly stored
and assigned to the remote control key
being used.
Driver messages
Applies to vehicles: with Audi side assist
If s ide ass ist switches off by itself, the LED in
the button turns off and a message will ap­
pear in the instrument cluster display:
Audi side assist unavailable: Sensors blocked
The radar sensors' vision is affected. Do not
cover the area in front of the sensors with bike
wheels, stickers, dirt or other objects. Clean
the area in front of the sensors, if necessary
¢ page 103, fig. 117.
Audi side assist: Currently unavailable
Side assist cannot be switched on temporarily
because there is a malfunc tion (for example,
the battery charge leve l may be too low) .
Audi side assist: System fault!
The system cannot guara ntee that it will de­
tect veh icles correctly and it is switched off .
The sensors have been displaced or are faulty.
H ave the system checked by an authorized
Aud i dealer or authorized Aud i Service Facility
soon.
Audi side assist: Unavailable when towing
Side assist sw itches off automatically when a
factory- insta lled trailer h itch is connected to
the electrical connector on the trailer. There is
no guarantee the system will switch off when
usi ng a retrofitted t ra iler hitch. Do not use
side assist when towing a trailer .
Audi side assist 105

Switching off
• Drive faster than 9 mph (15 km/h), or
• take the vehicle out of reverse gear. The
acoustic parking system is immediately de­
activated, and the rear view camera picture is deactivated automatically after a period
of about 15 seconds, or
• switch off the ignition.
The delay in deactivating the camera provides
an uninterrupted view behind the vehicle es­
pecially when maneuvering in tight parking
spaces and prevents the picture from turning
off the every time you sh ift out of reverse .
If the warning message appears in the display but not the rear view camera picture, read and
confirm the warning message . The acoustic
d istance signal is always active.
If you press a function button on the MMI
control console, the rear view camera picture
disappears . The rear view camera picture reap­
pears the next time you park.
Further information on the warning message
and the MMI control console can be found in
the MMI instruction booklet.
A WARNING
- Only use the rearview camera to assist
you if it shows a good, clear picture. For
example, the image may be affected by
the sun shining into the lens, dirt on the
lens or if there is a defect.
- Use the rearview camera only with the
rear lid completely closed. Make sure any
objects you may have mounted on the
rear lid do not block the rearview cam­
era.
(D Tips
- The rear v iew camera picture is available
as soon as the MMI Display or the MMI is
switched on, or the start-up phase is
completed.
- The sensors must be kept clean and free
of snow and ice for the park assist to op­
erate.
Park assist 113
- You can change the vo lume and pitch of
the signals as we ll as the disp lay
~page 115.
-What appears in the display is time-de­
layed.
Reverse Parking
App lies to vehicles: wit h parking system (rear, with rear
v iew camera}
Parking mode 1 can be used when parking in
a garage or parking space.
Fig. 125 MMI Display: Aim ing at a park ing spot
Fig. 1 26 MMI Disp lay : Al ign ing the veh icle
• Switch the MMI on and select the reverse
gea r.
• Turn the steering wheel until the orange ori­
entation lines (!) appear in the parking spot
i=> fig. 125. Use the markings @to help you
estimate the distance from an obstacle.
Each marking corresponds to 3 ft (1 m). The
blue area represents an extens ion of the ve­
hicle's outline by approximately 16 ft (5 m)
to the rear.
• Wh ile driving in reverse gear, adjust the
steer ing whee l angle to fit the parking space
with the aid of the orange orientation lines
i::>0 .@ marks the rear bumper. You should
stop driving in reve rse as soon as and no
Ill>-