2014.5 Citroen C5 tyre pressure

156
Braking assistance systems
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and
manoeuvrability of your vehicle when braking,
in particular on poor or slippery sur faces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself
felt by slight vibration of the brake pedal.
Operating fault
If this warning lamp comes on,
accompanied by an audible signal
and a message in the instrument
panel screen, it indicates a fault with
the anti-lock braking system which could result
in loss of control of the vehicle when braking.
If this warning lamp comes on,
together with the STOP and ABS
warning lamps, accompanied by an
audible signal and a message in the
instrument panel screen, it indicates a fault with
the electronic brake force distribution which
could result in loss of control of the vehicle
when braking.
You MUST stop as soon as it is safe to do so.
In both cases, contact a CITROËN dealer or a
qualified workshop.
Emergency braking
assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more
quickly, thus reducing the stopping distance.
Activation
It is triggered by the speed at which the brake
pedal is pressed.
The effect of this is a reduction in the
resistance of the pedal and an increase in
braking efficiency.
Group of supplementary systems which help
you to obtain optimum braking in complete
safety in emergency situations:
-

a

nti-lock braking system (ABS),
-

e

lectronic brake force distribution (EBFD),
-

e

mergency braking assistance (EBA).
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations.When braking in an emergency, press
firmly without releasing the pressure.
When braking in an emergency,
press very firmly without releasing
the

pressure.
Safety

190
F Remove the compressor and unclip and store the cartridge in a sealed bag to avoid
staining your vehicle with traces of fluid.
F

D
rive immediately for approximately
two
miles (three kilometres), at reduced
speed (between 15 and 35 mph [20 and
60
km/h]), to plug the puncture.
F

S
top to check the repair and the pressure. F
C onnect the compressor pipe directly to
the valve of the repaired wheel.
F
S
witch on the compressor by moving
the switch A to position

"1" until the tyre
pressure reaches 2.0 bars.
If this pressure has not been reached
after approximately five to ten minutes,
the tyre cannot be repaired; contact a
CITROËN dealer to have your vehicle
repaired.
Practical information

191
F Connect the compressor's electric plug to the vehicle's 12 V socket again.
F

S
tart the vehicle again and leave the
engine running. F
A djust the pressure using the compressor
(to inflate: switch A in position "1";
to
deflate: switch A in position "0" and
press button B ), in accordance with the
vehicle's tyre pressure label (located on
the door aperture on the left-hand side),
then remember to check that the leak has
been plugged correctly (no further loss of
pressure after several miles [kilometres]).
F

R
emove the compressor, then store the
whole kit.
F

D
rive at reduced speed (50 mph
[80
km/h] max) limiting the distance
travelled to approximately 120 miles
(200
km).
F

V
isit a CITROËN dealer or a qualified
workshop as soon as possible to have the
tyre repaired or replaced by a technician. Take care as sealant cartridge contains
ethylene-glycol. This product is harmful
if swallowed and causes irritation to the
eyes. Keep it out of reach of children.
The expiry date of the sealant is
indicated on the base of the cartridge.
The cartridge is designed for a single
use; even if only partly used, it must be
replaced.
After use, do not discard the cartridge
into the environment, take it to a
CITROËN dealer or an authorised
waste disposal site.
Do not forget to obtain a new cartridge,
available from CITROËN dealers or a
qualified workshop.
If the vehicle is fitted with tyre under-
inflation detection, the tyre under-

inflation warning lamp will remain on
after the wheel has been repaired until
the system is reinitialised by a CITROËN
dealer or a qualified workshop.
8
Practical information

193
Access to the spare wheel
To remove the spare wheel
F Saloon: raise the boot floor and fold in two.
F T ourer: raise the boot floor and hook it
using the retractable handle. Secure the
hook to the top part of the boot.
F
d
e
tach the strap then push the wheel
for wards so as to be able to lift it.
To reposition the spare wheel
F Position the spare wheel flat in the boot, then pull it towards you.
F

N
ext place the toolbox inside the wheel,
then secure the assembly with the strap.
F

R
elease the boot floor to return it to its
initial position. The tyre pressures are indicated on the
label located on the driver's side centre
door pillar. Tyre pressures are given for
different vehicle loading conditions.
8
Practical information

197
If your vehicle is fitted with a spare
wheel of a different size to those on the
vehicle, you must not exceed 50 mph
(80 km/h) whilst using the spare wheel.
The wheel bolts are specific to the type
of wheel.
If the type of wheel is changed,
check with your CITROËN dealer or a
qualified workshop that the wheel bolts
are compatible with the new wheels.
Take care to note down the code
number engraved on the head of the
security bolt socket. This will enable
you to obtain a replacement security
bolt socket from your dealer.
F

T

ighten the security bolt using
wheelbrace


1 and security bolt socket
(depending on equipment).
F

T

ighten the other bolts using just the
wheelbrace 1 .
F

R

efit the protectors on the bolts.
F

S

tow the tools in the carrier box.
F

R

eturn the suspension to the normal
position.
F

E

nsure the tyre pressure is correct and
have the balancing checked.Tyre under-inflation detection
The space-saver type or steel spare
wheel does not have a sensor.
The punctured wheel must be repaired
by a CITROËN dealer or a qualified
workshop.
8
Practical information

223
Blanking cover
When towing, you must remove the blanking
cover in the front bumper as well as the bonnet
seal if fitted.
Contact a CITROËN dealer or a qualified
workshop for this.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer.
The rear parking sensors will be
deactivated automatically if a genuine
CITROËN towbar is used.
Braking
Towing a trailer increases the braking distance.
To avoid overheating of the brakes on a long
mountain type of descent, the use of engine
braking is recommended.
8
Practical information

256
Identification markings
Various visible markings for identification of the vehicle.
The vehicle identification number (VIN) is also indicated on the registration document.
All genuine CITROËN replacement parts are available exclusively within the dealer network.
For your safety and in order to remain within the terms of the warranty, you are advised to use only
CITROËN replacement parts.A. V
IN plate O
n the left hand centre door pillar.
1.
E

U type approval number.
2.
V

ehicle Identification Number (VIN).
3.
G

ross vehicle weight.
4.
G

ross train weight.
5.
M

aximum weight on front axle.
6.
M

aximum weight on rear axle.
B.
V

IN stamped on body
C.
V

IN on dashboard
D.
P

aint colour code and tyre reference
T

yre pressures
O

n the driver's side centre pillar.Observe the tyre pressures indicated by
CITROËN.
Check the tyre pressures regularly,
when cold.
Never deflate a warm tyre.
When changing tyres, it is essential
to
use the sizes recommended for
your
vehicle.
Technical data