2014.5 Citroen C4 clutch

199
Cruise control
The functions of this system are grouped together   on   the   steering   mounted   controls.
1.
 C

ruise   control   mode   selection   dial.
2.
 S

peed   programming   /   value   decrease  
b

utton.
3.
 S

peed   programming   /   value   increase  
b

utton.
4.
 C

ruise   control   off   /   resume   button.
5.
 M

emorised   speeds   display   button.
Steering mounted controls
The programmed information is grouped together   in   the   instrument   panel   screen.
6.
  C

ruise   control   off   /   resume   indication.
7.
  C

ruise   control   mode   selection   indication.
8.
  P

rogrammed   speed   value.
9.
  S

electing   a   stored   speed.
Displays in the instrument panel
The cruise control is switched on m anually: it r
equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h)   and   engagement   of:
-
 
f
ourth   gear   on   the   manual   gearbox,
-
 
s
econd   gear   on   the   electronic   gearbox  
s

ystem   or   automatic   gearbox,   in   sequential  
d

riving   mode,
-
 
p
osition   A   on   the   electronic   gearbox  
s

ystem   or   D   on   an   automatic   gearbox.
The cruise control is switched off
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems,   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value.
The cruise control system cannot, in any circumstances, replace   the   need   to   observe   speed   limits,   nor   can   it r

eplace   the   need   for   vigilance   on   the   part   of   the   driver.
You
  are   advised   to   keep   your   feet   near   the   pedals   at
 a

ll   times.
System which automatically maintains the speed of the vehicle at the value programmed by the driver,   without   any   action   on   the   accelerator   pedal.
Operation
9
driving

Driving
6
Stop & Start
Operation
Going into engine STOP mode
The "ECO" warning lamp comes on in the instrument panel and the engine goes into standby automatically:
- with a manual gearbox , at speeds below 12 mph (20 km/h), or vehicle stationary with PureTech 130 petrol and BlueHDi 115 and 120 Diesel versions, when you put the gear lever into neutral and release the clutch pedal, - with an electronic gearbox , at a speed below 5 mph (8 km/h), when you press the brake pedal or place the gear lever in position N , - with an automatic gearbox, vehicle stationary, when you press the brake pedal or place the gear lever in position N .
If your vehicle is fitted with the system, a time counter calculates the sum of the periods in STOP
Special cases: STOP mode unavailable
STOP mode is not invoked when: - the vehicle is on a steep slope (up or down), - the driver's door is open, - the driver's seat belt is not fastened, - the vehicle has not exceeded 6 mph (10 km/h) since the last engine start (using the key or the "START/STOP" button), - the electric parking brake is applied or being applied, - the engine is needed to maintain a comfortable temperature in the passenger compartment, - demisting is active, - some special conditions (battery charge, engine temperature, braking assistance, ambient temperature...) where the engine is needed to assure control of a system.
In this case, the "ECO" warning lamp flashes for a few seconds, then goes of f. This operation is perfectly normal.
The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently. Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
STOP mode does not affect the functionality of the vehicle, such as braking, power steering, for example. Never refuel with the engine in STOP mode; you must switch off the ignition
with the key or the "START/STOP" button.
With an electronic gearbox, for your comfort during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse g e a r.
mode during a journey. It resets itself to zero every time the ignition is switched on with the key or the "START/STOP" button.

9
Driving7
Going into engine START mode
Special cases: START invoked automatically
The "ECO" warning lamp goes off and the engine starts automatically:
- with a manual gearbox , when you fully
depress the clutch pedal, - with an electronic gearbox : ● gear lever in position A or M , when you release the brake pedal, ● or gear lever in position N and the brake pedal released, when you place the gear lever in position A or M , ● or when you engage reverse gear. - with an automatic gearbox: ● gear lever in position D or M , when you release the brake pedal, ● or gear lever in position N and brake pedal released, when you place the gear lever in position D or M , ● or when you engage reverse gear.
For safety reasons or to ensure smooth operation, START mode is invoked automatically when: - you open the driver's door,
- you unfasten the driver's seat belt, - the speed of the vehicle exceeds 15 mph (25 km/h) with a manual gearbox (3 km/h (2 mph) with PureTech 130 petrol and BlueHDi Diesel 115 and 120 versions), 7 mph (11 km/h) with an electronic gearbox or 2 mph (3 km/h) with an automatic gearbox, - the electric parking brake is being applied, - some special conditions (battery charge, engine temperature, braking assistance, ambient temperature...) where the engine is needed to assure control of a system.
In this case the "ECO" warning lamp flashes for few seconds, then goes of f.
This operation is perfectly normal.
With a manual gearbox in STOP mode, if a gear is engaged without fully depressing the clutch pedal, a warning lamp comes on or an alert message is displayed asking you to depress the clutch pedal to restart the engine.

Driving
14
Cruise control
1. Cruise control mode selection wheel. 2. Button for setting the current speed of the vehicle as the cruise setting or lowering the cruise setting. 3. Button for setting the current speed of the vehicle as the cruise setting or raising the cruise setting. 4. Cruise control pause / resume button. 5. Display memorised speed settings button.
Steering mounted controls
6. Cruise control pause / resume indication. 7. Cruise control mode selected indication. 8. Cruise speed setting. 9. Selecting a memorised cruise speed.
Displays in the instrument panel
System which automatically maintains the cruising speed of the vehicle at a setting programmed by the driver, without any action on the accelerator pedal.
The operation of the cruise control can be interrupted (pause): - by pressing control 4 or by pressing the brake or clutch pedal, - automatically, if operation of the dynamic stability control system is triggered.
The cruise control is switched onmanually. It requires a minimum vehicle speed of 25 mph (40 km/h) as well as: - with a manual gearbox, the engagement of fourth gear or higher, - with an electronic gearbox, the gear selector at position A , or second gear or higher in manual mode, - with an automatic gearbox, the gear selector at position D or second gear or higher in manual mode.
Switching off the ignition cancels any programmed speed setting.
The cruise control system is a driving aid that cannot, in any circumstances, replace the need to observe speed limits, nor the
need for vigilance on the part of the driver. As a safety measure, you are advised to keep your feet near the pedals at all times.