2014.5 Citroen C4 CACTUS RHD engine

83
5-speed manual gearbox
Engaging reverse gear
F Press  the   clutch   pedal   fully   down.
F  P ush   the   gear   lever   fully   to   the   right   then  
ba

ckwards. Only
  engage   reverse   gear   when   the
 v

ehicle   is   stationary   with   the   engine   at   idle.
As   a   safety   precaution   and   to   facilitate  
s

tarting   of   the   engine:
-  
a
lways   select   neutral,
-  
p
ress   the   clutch   pedal.
5
Driving

84
Operation
Gear efficiency indicator
System which reduces fuel consumption by advising the driver to change up, on vehicles fitted with a manual gearbox.
T he   system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (slope,   load,   ...)   and  
t

he   demands   of   the   driver   (power,  
a

cceleration,   braking,   ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear,
-
 
e
ngaging   a   lower   gear.
Example:
-
 
Y
ou   are   in   third   gear.
Depending
  on   the   driving   situation   and   your  
v

ehicle's   equipment,   the   system   may   advise  
y

ou   to   skip   one   (or   more)   gear(s).   You   can  
f

ollow   this   instruction   without   engaging   the  
i

ntermediate
 g
ears.
-
 
Y
ou   press   the   accelerator   pedal.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
The
  information   appears   in   the   instrument  
p

anel   in   the   form   of   an   arrow,   accompanied   by  
t

he   recommended   gear.
On
  certain   Diesel   versions   with   manual  
g

earbox,   the   system   may   suggest  
c

hanging   into   neutral   (N
  is   displayed   in  
t

he   instrument   panel)   so   that   the   engine  
c

an   go   into   standby   (STOP   mode  
w

ith   Stop   &   Start),   in   certain   driving  
c

onditions.
The
  gear   engagement   recommendations   must  
n

ot   be   considered   compulsory.   In   fact,   the  
c

onfiguration   of   the   road,   the   amount   of   traffic  
a

nd   safety   remain   determining   factors   when  
c

hoosing   the   best   gear.   Therefore,   the   driver  
r

emains   responsible   for   deciding   whether   or   not  
t

o   follow   the   advice   given   by   the   system.
This
  system   cannot   be   deactivated.
Driving

85
ETG electronic gearbox
N Neutral:  with   your   foot   on   the   brake,   press  t
his   control   to   put   the   gearbox   into   neutral  
a

nd   for   starting   the   engine.
D
 
D
rive:   press   this   control   to   engage   for ward  
d

rive   with   automatic   operation   of   the   gears.
R
 
R
everse:   with   your   foot   on   the   brake,   press  
t

his   control   to   engage   reverse.
Control panel
F Press  the   back   of   the   paddle   to  t
he right  of   the   steering   wheel   to  
ch

ange up .
Steering mounted controls
The steering mounted paddles do not a
llow   neutral   to   be   selected,   or   reverse  
g

ear   to   be   engaged   or   disengaged.
Five
 
or
 
six-speed
 
electronically
 
controlled
 
gearbox
 
which
 
offers   the   comfort   of   automatic   control   of   the   gears,   without   any   action   by   the   driver.
You
 
can
 
temporarily
 
take
 
control
 
of
 
gear
 
changes
 
at
 
any
 
time,   using   the   steering   mounted   control   paddles.
F  
P
ress   the   back   of   the   paddle   to  
t

he left
 
of   the   steering   wheel   to  
ch

ange down
.
Display in the instrument panel
F Place your foot on the brake
when   this   warning   lamp   flashes.
N
n
e

utral
D
 
and
 
1 2 3 4 5 / 6   
D
rive   (for ward   drive)   and   the  
g

ear
 enga
ged.
R

Reverse
5
Driving

86
N flashes in the instrument panel, accompanied   by   an   audible   signal   and  
a

  message   if   the   control   N has not been
pressed
  for   starting.
Press control N
  to   select   neutral.
Moving off
F Switch  on   the   ignition.
F  S elect   neutral   (control   N).
 T

he   indicator   lamp   for   the   control   comes   on.
F
 
P
ress   the   brake   pedal   fully.
F
 
S
tart   the   engine. N
  appears   in   the   instrument   panel.
F  
S
elect   for ward   drive   (control   D)
  or   reverse  
(c

ontrol
 R). T

he   associated   indicator   lamp   comes   on   in  
t

he   control   panel.
D
  and   1 or R   appear   in   the   instrument  
pan

el.Creep function
This function allows the vehicle to be
manoeuvred  more   easily   at   low   speeds   (when  
p

arking,   in   traffic   jams...).
After
  pressing   control   D or R, the vehicle
moves as soon as you take your foot off the
brake pedal ,
  at   low   speed   and   with   the   engine  
a

t   idle.
The
  creep   function   may   be   temporarily  
u

navailable   if   the   clutch   temperature   is  
t

oo   high   or   the   slope   too   steep.
Do
  not   leave   children   unsupervised  
i

nside   the   vehicle   when   the   engine   is  
r

unning.
You
 
must
 
keep
 
your
 
foot
 
on
 
the
 
brake
 
p

edal
 
while
 
starting
 
the
 
engine.
The
 
"Foot
 
on
 
the
 
brake"
 
warning
 
and
 
t

he
 
associated
 
control
 
panel
 
indicator
 
l

amp
 
flash
 
if
 
the
 
brake
 
pedal
 
is
 
not
 
p

ressed
 
when
 
starting
 
the
 
engine.
Press
 
firmly
 
on
 
the
 
brake
 
pedal. F
 
R

elease
 
the
 
parking
 
brake.
F
 
P

rogressively
 
take
 
your
 
foot
 
off
 
the
 
brake
 
ped

al.
 T

he
 
vehicle
 
moves
 
off.
Driving

87
Never select neutral (position N)   when  m
oving.
Forward drive
F Press control D . T
he   indicator   lamp   in   the   control   comes   on.
D
  and   the   gear   engaged   appear   in  
t

he   instrument   panel.
The
  gearbox   then   operates   in   auto-adaptive  
m

ode,   without   any   action   on   the   part   of   the  
d

river.   It   continuously   selects   the   most   suitable  
g

ear   taking   account   of:
-
 
o
ptimisation   of   fuel   consumption,
-
 
d
riving   style,
-
 
r
oad   conditions,
-
 
v
ehicle   load.
For
  optimum   acceleration,   when  
ov

ertaking   another   vehicle   for   example,  
p

ress   the   accelerator   pedal   fully   down,  
b

eyond   the   point   of   resistance.
Temporary control of gear
changing
You can temporarily take over control of gear changes   using   the   steering   mounted   "+"  and "-"
control
  paddles:   if   the   engine   speed   allows,   the
 g

ear   change   is   carried   out.
This function allows you to anticipate certain
situations
 
s
uch  
a
s  
ov
ertaking  
a
nother  
v
ehicle  
o
r  
a

pproaching   a   bend.
After
  a   few   moments   without   any   action   on   the  
p

addles,   the   gearbox   resumes   control   of   gear  
c

hanging
 a
utomatically. To
  engage   reverse,   the   vehicle   must   be  
i

mmobilised   with   your   foot   on   the   brake.
F
P
ress control R
.
 T
he   indicator   lamp   in   the   control   comes   on.
Reverse
There is an audible signal on enga
gement o f r everse.
If
 
reverse   gear   is   requested   when   moving,  
t

he

N
 
warning   lamp   flashes   and   the   gearbox  
g

oes
 
into   neutral   automatically.
To
 
engage   reverse,   stop   the   vehicle   then,   with  
y

our
 
foot   on   the   brake   pedal,   press   control   N,
then R .
Do
 
not
 
press
 
the
 
brake
 
and
 
accelerator
 
p

edals
 
at
 
the
 
same
 
time:
 
this
 
could
 
c

ause
 
very
 
rapid
 
wear
 
of
 
the
 
clutch.
5
Driving

88
Before switching off the engine:
-  p ress   control   N to be in neutral,


or
-
 
l
eave   the   vehicle   in   gear;   in   this   case   the  
v

ehicle   cannot   be   moved.
Stopping the vehicle
For all parking situations, you must
ap ply the parking brake  to   immobilise  
t

he   vehicle.
When
  immobilising   the   vehicle   with  
t

he   engine   running,   you   must   select  
neu

tral

N.
Operating fault
- - - appears in the instrument panel.
F

P

ress control N .
F
 
P

ress
  the   brake   pedal.
F
 
W

ait
 
for   around   30   seconds   until   N or a
gear
 
appears   in   the   instrument   panel.
F

P

ress control D , then N.
F
 
W

ith
 
your   foot   still   on   the   brake   pedal,   start  
t

he
 eng
ine.
The
 
gearbox   is   operational   again.
Reinitialisation
(5-speed electronic
gearbox)
Following disconnection of the battery, it is necessary   to   reinitialise   the   gearbox.
F
 
S
witch   on   the   ignition.
In
  exceptional   circumstances,   the  
g

earbox   may   need   an   automatic  
r

einitialisation:   starting   and   gear  
c

hanging   are   no   longer   possible.
- - -
  appears   in   the   instrument  
pan

el.
Follow
  the   procedure   described   above.
Before
 
d

oing
 
a

nything
 
u

nder
 
t

he
 
b

onnet,
 
e

nsure that control N
 
has
 
been
 
pressed
 
a

nd
 
that
 
the
 
parking
 
brake
 
is
 
applied. With
  the   ignition   on,   illumination   of  t
his   warning   lamp,   accompanied   by  
a

n   audible   signal   and   a   message,  
i

ndicates   a   gearbox   fault.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Driving

89
Hill start assist
System which keeps your vehicle immobilised temporarily   (approximately   2   seconds)   when  
s

tarting   on   a   gradient,   the   time   it   takes   to  
m

ove   your   foot   from   the   brake   pedal   to   the  
a

ccelerator
 ped
al.
This
  system   only   operates   when:
-
 
t
he   vehicle   is   completely   stationary,   with  
y

our   foot   on   the   brake   pedal,
-
 
c
ertain   conditions   of   slope   are   met,
-
 
w
ith   the   driver’s   door   closed.
The
  hill   start   assist   system   cannot   be  
d

eactivated. On an ascending slope, with the vehicle
stationary, the vehicle is held momentarily
when you release the brake pedal, provided
that:
-
 
y
ou   are   in   first   gear   or   neutral   with   a  
m

anual
 g
earbox,
-
 
y
ou   are   in   position   D with an electronic
gearbox.Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
Operating fault
If a fault in the system occurs, these warning l amps   come   on,   accompanied   by   an   alert  
m

essage.   Contact   a   CITROËN   dealer   or  
a

  qualified   workshop   to   have   the   system  
c

hecked.
Do
 
not
 
leave
 
the
 
vehicle
 
while
 
it
 
is
 
being
 
h

eld
 
in
 
the
 
hill
 
start
 
assist
 
phase.
If
 
you
 
need
 
to
 
exit
 
the
 
vehicle
 
with
 
t

he
 
engine
 
running,
 
apply
 
the
 
parking
 
b

rake.
5
driving

90
Stop & Start
Operation
Going into engine STOP mode
The "ECO"  warning   lamp   comes   on i
n   the   instrument   panel   and   the   engine g

oes   into   standby   automatically:
-
 
w

ith a manual gearbox , when stationary,
in
 
neutral,   and   you   release   the   clutch  
ped

al.
-
 
w

ith an electronic gearbox , when
stationary
  or   at   speeds   below   5   mph  
(

8 km/h)   (depending   on   version),   in   neutral  
(

control   on   N)
  or   when   you   press   the   brake  
ped

al. Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   button.
For
  your   comfort,   during   parking  
m

anoeuvres,   STOP   mode   is   not  
a

vailable   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
STOP
  mode   does   not   affect   the   the  
v

ehicle's   systems,   such   as   for   example,  
b

raking,   power   steering...
Special cases: STOP mode not
available
STOP mode is not invoked principally when:
-  t he   vehicle   is   on   a   steep   slope   (rising   or  
f

alling),
-
 
t
he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   by   the  
d

river,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, the "ECO"
 

warning  
l

amp   flashes   for   a   few   seconds   then  
g

oes off.
This operation is perfectly normal.
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
temporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
stops
 
in
 
the
 
traffic   (red   lights,   traffic   jams,  
or
 
other...).
 
The engine
 
restarts
 
automatically
 
-
 
START
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
off.
 
The
 
restart   takes   place   instantly,   quickly  
and
 
silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when  
stationary.
Stop & Start time counter
A cumulative time counter for periods i n   STOP   mode   during   a   journey.
It
 
is
 
displayed   in   the   trip   computer   (accessible  
v

ia the " Driving assistance "
  menu   of   the  
t

ouch
 
screen   tablet).
It resets to zero every time the ignition is switched on.
driving