2014.5 Citroen BERLINGO MULTISPACE RHD brake

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
30
Warning lamps
Each time the vehicle is started: a series of warning lamps comes on applying a self-test check. They  go   off   almost   immediately.
When   the   engine   is   running:   the   warning   lamp   becomes   a   warning   if   it   remains   on   continuously   or   flashes.  
This
  initial   warning  
may

  be   accompanied   by   an   audible   signal   and   a   message   which   appears   in   the   screen.
Do
  not   ignore   these   warnings.
Warning lamp is indicatesSolution - action
S t
OP on, associated
with another
warning
lamp

  and  
accompanied

 
by

  a   message  
in

  the   screen.major
  faults   linked   with  
the

  "Brake   fluid   level",  
"Engine oil pressure and
temperature",

  "Coolant  
temperature",

  "Electronic  
brake

  force   distribution"   and  
"Power steering" warning
lamps.Y

ou must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a
c I tr OË n dealer or a qualified
workshop.
Parking
brake / Brake
fluid level /
EBF
d
on.that the parking  brake  is  applied or
  has   not   been   released   fully.Releasing the parking brake switches off the warning  lamp.
on. low
 
brake
 
fluid
 
level. Top   up   using   a   fluid   recommended   by   CITROËN.
remaining on even though the level
is correct and
associated with the
ABS
 
warning
 
lamp.
a fault with the electronic
brake  force   distribution. You must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a CITROËN dealer or a qualified
workshop.
Engine oil
pressure and
temperature on while
driving.
low pressure or a high
temperature. Park
  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
Chapter
  7,   "Levels"   section.
remaining on, even though the
level  is   correct.a major fault. Have   it   checked   by   a   CITROËN   dealer   or   a  qualified
  workshop.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
40
The alert is maintained until the tyre or tyres concerned is
reinflated,  repaired   or   replaced.
The spare wheel (space-saver type or
a
 
steel   rim)   does   not   have   a   sensor.
Operating faultu
nder-inflation alert
The loss of pressure detected
does not always lead to visible
deformation
 
of
 
the
 
tyre.
 
Do
 
not
 
rely
 
on

  just   a   visual   check.The alert is given by the fixed illumination   of   this   warning   lamp,  
accompanied

  by   an   audible   signal,  
and

  depending   on   equipment,   the  
display

  of   a   message.The flashing and then fixed  illumination   of   the  
under-inflation

  warning  
lamp

  accompanied   by   the  
illu

mination   of   the   "Service"   warning  
lamp,

 
and   depending   on   equipment,  
the

 
display   of   a   message   indicates   a  
fault

 
with   the   system.
In
 
this
 
case,   monitoring   of   the   tyre  
pressures

  is   not   assured.
In
 
the
 
event
 
of
 
a
 
problem
 
on
 
one
 
of
 
the

 
tyres,
 
the
 
symbol
 
or
 
the
 
message
 
appears,

 
according
 
to
 
equipment,
 
to
 
identify

 
it.
-

Reduce speed, avoid sudden
steering

 
movements
 
or
 
harsh
 
brake
 
applications.
-

 
Stop

 
as
 
soon
 
as
 
it
 
is
 
safe
 
to
 
do
 
so.
-

In the event of a puncture, use
the

 
temporary
 
puncture
 
repair
 
kit
 
or the spare wheel (according to
equipment),
or
-

 
if

 
you
 
have
 
a
 
compressor,
 
the
 
one
 
in

 
the
 
temporary
 
puncture
 
repair
 
kit

 
for
 
example,
 
check
 
the
 
four
 
tyre
 
pressures when cold,
or
-

 
if

 
it
 
is
 
not
 
possible
 
to
 
check
 
the
 
tyre

 
pressures
 
at
 
the
 
time,
 
drive
 
carefully

 
at
 
reduced
 
speed. This alert is also displayed when
one
  or   more   wheels   is   not   fitted  
with

  a   sensor   (for   example,   a  
space-saver

  or   steel   spare   wheel).
Go
 
to
 
a   CITROËN   dealer   or   a   qualified  
workshop to

  have   the   system   checked  
or

, following the repair of a puncture, to
have
 
the   original   wheel,   equipped   with  
a

 
sensor,   refitted.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
45
6-SPEEd ELEctrOnIc GEArBOX
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It
  is   only   possible   to   come   out  
of position

n  if   the   brake   pedal   is  
pressed.
The

  change   from   position   A (driving in
automatic
  mode)   to   position   M (driving
in
  manual   mode)   or   vice   versa   can   be  
made

  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector   must   be   in   position  n .
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

r , A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

n ,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
r

everse gear Engaging reverse gear
Move the gear selector to
r .
Only attempt to select reverse gear
when the vehicle is stationary.
n

eutral
c

hanging to neutral
Move the gear selector to
n .   If   the  
vehicle

  is   moving,   do   not   select   this  
position

  even   momentarily.
Gearbox and steering wheel
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
46
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes  automatically   to   neutral  n .
Stopping the vehicle
Before stopping the engine, put the
gear selector in position n .
In all cases, it is essential to apply
the
  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

n .
changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed

  (for   example   when  
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator

  completely   during   gear  
changes.
-

a
gear change instruction is
accepted only if the engine speed
permits.
-


For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
c

hanging to manual mode
Move the gear selector to M. Automatic mode
c

hanging to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic
 
mode,
 
without
 
any
 
action
 
on
 
your

 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
47
StOP & StArt
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine StOP mode
The "E c O"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with the 6-speed electronic gear
control gearbox

, at a speed below
5
  mph   (8   km/h),   when   you   press  
the

  brake   pedal   or   put   the   gear  
lever into position

n .If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   the   automatic   gearbox  
system,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: S t
OP
mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"E c O"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
t

his operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
48
Going into engine StArt mode
The "EcO" warning lamp goes
  off   and   the   engine   starts:
- with a manual gearbox , when you
fully depress the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position  n and
the
  brake   pedal   released,   when  
you

  move   the   gear   lever   to  
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With
  a   manual   gearbox   in   STOP
 mode,

  if   a   gear   is   engaged   without  
fully depressing the clutch pedal, a
warning

  lamp   comes   on   or   a   message  
is

  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.Special cases: S
t
A
rt invoked
automatically
For   your   safety   and   comfort,   START
 
is  
invoked

  automatically   when:
-
you open the driver's door
,
-
you unfasten the driver's seat belt,
-
the speed of the vehicle exceeds
15
  mph   (25   km/h)   with   a   manual  
gearbox

  or   7   mph   (11   km/h)   with  
the

  6-speed   electronic   gearbox  
system,
-

 
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.In this case the

"E c O"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
t

his operation is perfectly normal.
deactivation
At any time, press the "EcO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp

 
coming   on   accompanied   by   a  
message

  in   the   screen.
If
 
the
 
system   has   been   deactivated  
in

 
STOP
 

mode,   the   engine   restarts  
immediately

.
Stop & Start

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
51
HILL StA rt ASSIS t
This system (also called HHC - Hill Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-
 
the
  vehicle   must   be   stationary,  
engine

  running,   foot   on   the   brake,
-
 
the
  gradient   of   the   road   must   be  
steeper than 5%,
-

 
uphill,
  the   gearbox   must   be   in  
neutral or in a gear other than
reverse,
-

 
downhill,
  reverse   gear   must   be  
engaged.
The Hill Start
a

ssist function is
a
  driving   aid   system.   It   is   not   an  
automatic

  vehicle   parking   function   or  
an

  automatic   parking   brake.
Operation
With the brake pedal and clutch pedal pressed,  from   the   time   you   release   the  
brake

  pedal   you   have   approximately  
2 seconds before the vehicle starts to
roll

  back   and   without   using   the   parking  
brake

  within   which   to   move   off.
During
  the   moving   off   phase,   the  
function

  is   deactivated   automatically,  
gradually

  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic

  noise   of   mechanical  
release

  of   the   brakes   may   be   heard,  
indicating

  the   imminent   movement   of  
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If
  a   malfunction   of   the  
system

  occurs,   this  
warning

  lamp   comes   on  
accompanied

  by   an   audible  
signal

  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   at   a   CITROËN  
dealer

  or   a   qualified   workshop.
Starting and stopping
REadY To Go
3

58
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
Selecting the function
- Place the switch in the cru ISE
position.  The   cruise   control   is  
selected but is not yet active and
no

  speed   has   been   programmed.
First activation /
Programming a
speed
temporarily exceeding the
speed
It is possible to accelerate and drive
momentarily   at   a   speed   greater   than  
the

  programmed   speed.  
The
  value  
programmed

  flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed
  speed.
deactivation (off)
- Press this button or
the  brake   or   clutch  
pedal.
reactivation
- Following deactivation of the cruise
control,  press   this   button.
Your vehicle will return to the last
programmed
  speed.
Alternatively,
  you   can   repeat   the   "first  
activation"

  procedure.
-

Reach the chosen speed by
pressing

 
the
 
accelerator.
-

Press the

SE
t
- or SE
t
+
 
button.
This
 
programmes/activates
 
the
 
reference speed and the vehicle will
maintain

 
this
 
speed.
Steering mounted controls