2014.5 Citroen BERLINGO MULTISPACE RHD battery

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
42
trip recorder zero reset button
after this operation, if you wish
to   disconnect   the   battery,   lock  
the vehicle and wait for at least
five minutes,

  otherwise   the   zero   re-set  
will

 
not   be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates  
a
 
malfunction of the engine oil level


indicator.   Contact
 a

  CITROËN   dealer   or   a   qualified
 workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.
d
ipstick
A   =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero re-set
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
47
StOP & StArt
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine StOP mode
The "E c O"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with the 6-speed electronic gear
control gearbox

, at a speed below
5
  mph   (8   km/h),   when   you   press  
the

  brake   pedal   or   put   the   gear  
lever into position

n .If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   the   automatic   gearbox  
system,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: S t
OP
mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"E c O"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
t

his operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
48
Going into engine StArt mode
The "EcO" warning lamp goes
  off   and   the   engine   starts:
- with a manual gearbox , when you
fully depress the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position  n and
the
  brake   pedal   released,   when  
you

  move   the   gear   lever   to  
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With
  a   manual   gearbox   in   STOP
 mode,

  if   a   gear   is   engaged   without  
fully depressing the clutch pedal, a
warning

  lamp   comes   on   or   a   message  
is

  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.Special cases: S
t
A
rt invoked
automatically
For   your   safety   and   comfort,   START
 
is  
invoked

  automatically   when:
-
you open the driver's door
,
-
you unfasten the driver's seat belt,
-
the speed of the vehicle exceeds
15
  mph   (25   km/h)   with   a   manual  
gearbox

  or   7   mph   (11   km/h)   with  
the

  6-speed   electronic   gearbox  
system,
-

 
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.In this case the

"E c O"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
t

his operation is perfectly normal.
deactivation
At any time, press the "EcO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp

 
coming   on   accompanied   by   a  
message

  in   the   screen.
If
 
the
 
system   has   been   deactivated  
in

 
STOP
 

mode,   the   engine   restarts  
immediately

.
Stop & Start

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
49
reactivation
Press the "EcO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "E c O
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

53
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
LEd dAYtIME runnInG LAMPS
Rear foglamps (amber, 2nd rotation  of   the   ring   forwards).
Front
  foglamps   (green,   1st  
rotation

  of   the   ring   forwards).
Front and rear foglamps
Rotate ring B forwards to switch on
and
 
rearwards   to   switch   off.  
The
  status  
is

 
confirmed   by   the   warning   lamps   in  
the

 
instrument   panel.
They
 
operate   with   the   sidelamps   and  
dipped

 
beam   headlamps. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and rear
foglamps,   turn   the   ring   rearwards   twice  
in

 
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the   sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the A
ut
O
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
d

eactivation
Turn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and
 
night,
 
rear
 
foglamps
 
dazzle
 
and
 
their

 
use
 
is
 
prohibited.
Refer to chapter 8, "Battery
section".
Steering mounted controls
EaSE oF USE and CoMFoRT
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
98
12 Volt socket (120 W Max)
It is advisable to limit the use of this socket  to   avoid   discharging   the   battery.
Protective net
Open the cover located in the hook support.
Fix the top of the net in the notches,
having
  first   turned   the   bar   1/4   of   a   turn.
Ensure that the end of the bar engages
correctly
  in   the   metal   part   of   its  
location.
Fix the straps in the locations provided
on

  the   floor.
Tighten
  the   net   using   the   straps.
Stowing rings
Use these rings to secure loads on the
floor.
Practical information

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 99
rEAr FIttInGS
(7 SEAt VE r SIO n)
c

up holder
Any liquid carried in a cup (mug or other) on board which could spill,
presents   a   risk.
Take
  care.
12 volt socket (120 W max)
It is advisable to limit the use of this socket   to   avoid   discharging   the   battery.
Stowing rings
Use the stowing rings on the floor to secure  and   retain   your   loads   firmly.
The
  seat   belt   anchorages   must   not   be  
used

  for   this   purpose.
 It

  is   recommended   that   the   load  
is

  immobilised   by   securing   it  
firmly

  using   the   stowing   rings   on  
the floor

.
Practical information
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
105
ELEctrIc WIndOWS
1. driver's side
2.
Passenger's side Lower the window fully

, then raise it, it
will   rise   in   steps   of   a   few   centimetres  
each

  time   the   control   is   pressed.  
Repeat the operation until the window
is

  fully   closed.
Continue to press the control for at
least one second after the window
closed   position   has   been   reached.
The safety anti-pinch does not operate
during   these   operations.
Safety anti-pinch
When the window rises and meets an obstacle,
  it   stops   and   partially   lowers.One-touch mode
Press or pull the control, beyond the
point  of   resistance.  The   window   opens  
or closes fully when the control is
released.

  Pressing   the   control   again  
stops

  the   movement   of   the   window.This
  mode   is   available  
depending

  on   equipment;   it   is  
identified

  by   this   symbol   on   the  
control

  in   question.
Good practice
If the electric windows meet an obstacle
  during   operation,   you   must  
reverse

  the   movement   of   the   window.  
T

o  
do
 
this,
 
press
 
the
 
control
 
concerned.
When the driver operates the
passenger electric window controls,
they

  must   ensure   that   no   one   is  
preventing correct closing of the
windows.
The

  driver   must   ensure   that   the  
passengers use the electric windows
correctly

.
Be aware of children when operating
the
  windows.
Following
  several   consecutive   closing/
opening operations of the electric
window
  control,   a   protection   system  
is triggered which only allows closing
of

  the   window.  
After
  closing,   wait  
approximately

  40   minutes.   Once   this  
time

  has   elapsed,   the   control   becomes  
operational

  again.
Manual mode
Press or pull the control, without
passing  the   point   of   resistance.  The  
window stops when you release the
control.
reinitialisation
Following reconnection of the battery,
or  in   the   event   of   a   malfunction,   the  
safety

  anti-pinch   function   must   be  
reinitialised. The electrical functions of the electric
windows
  are   deactivated:
-  
approximately
  45   seconds   after   the  
ignition is switched of

f,
-
after one of the front doors is
opened,

  if   the   ignition   is   off.
There
 
are
 
two
 
operating
 
modes:
Mirrors and windows
EaSE oF USE and CoMFoRT
4