Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
28
dials
1. Distance recorder in kilometres / miles.
2.
Screen.
3.
Fuel
level, coolant temperature.
4.
Rev
counter.
5.
T
rip distance recorder / service
indicator
zero reset.
6.
Instrument
panel lighting dimmer.
Level 2 display screen
Instrument panel
Level 1 display screen
displays
- Speed limiter / Cruise control.
-
Kilometres
/ Miles travelled.
-
Service
indicator, total kilometres /
miles.
-
Presence of water in the
d iesel
filter.
-
Diesel
pre-heating.
Screens
The format of the information presented in the screen depends on
the vehicle's equipment.
Instruments and controls
Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
41
SErVIc E I nd I c AtO r
This programmes service intervals according
to the use of the vehicle.More than 1 000 miles/km before the
next service is due
Example:
4 800 miles/km remain
before
the next service is due. When
the ignition is switched on and for a
few
seconds, the screen shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
recorder resumes normal
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each
time the ignition is switched on
and for a few seconds, the spanner
flashes
and the number of miles/
kilometres
remaining is displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
recorder resumes normal
operation
and the spanner remains on.
This indicates that a service should be
carried
out shortly.
Service overdue
Operation
A
few moments after the ignition
has been switched on, the spanner
indicating
a service operation comes
on; the display for the total distance
recorder
gives (in round figures) the
distance
remaining before the next
service.
The points at which a service is due
are
calculated from the last indicator
zero
reset.
The point at which a service is due is
determined
by two parameters:
-
the distance travelled,
-
the
time which has elapsed since
the
last service.
The
distance remaining before the
next
service may be weighted by
the
time factor, depending on the
type
of driving. With the engine running the spanner
remains
on until the service has been
carried
out.
For BlueH
d i d iesel versions, this
alert
is also accompanied by the fixed
illu
mination of the Service warning
lamp,
on switching on the ignition.
Each
time the ignition is
switched on and for a few
seconds, the spanner
flashes
and the excess
distance
is displayed.
For BlueH
d i d iesel versions, the
spanner
can also come on early,
according the level of deterioration
of
the engine oil. Deterioration of the
engine oil depends on the conditions of
use
of the vehicle.
Instruments and controls
REadY To Go
3
Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
42
trip recorder zero reset button
after this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
five minutes,
otherwise the zero re-set
will
not be registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
after the service information. Oil level correct
Low oil level
Flashing of "OIL",
linked
with the
service
warning lamp,
accompanied
by an
audible
signal and a message in the
screen, indicates a low oil level which
could
damage the engine.
If the low oil level is confirmed by a
check
using the dipstick, it is essential
that
the level is topped up.
Oil level gauge fault
Flashing of "OIL--"
indicates
a
malfunction of the engine oil level
indicator. Contact
a
CITROËN dealer or a qualified
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
than 30 minutes.
d
ipstick
A = maximum, never exceed
this level as a surplus of oil
may
damage the engine.
Contact a CITR o Ë n dealer
or a qualified workshop
without
delay.
B
=
minimum,
top
up
the
level
via
the oil filler cap, using the
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
and controls.
When the lighting
reaches
the minimum (or
maximum)
setting, release the button
then press it again to increase (or
reduce)
the
brightness.
a
s soon as the lighting is of the
required
brightness, release the button.
Zero re-set
Your CITROËN dealer or a qualified workshop carries out this operation
after
each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-
switch of
f the ignition,
-
press and hold the trip recorder
reset button,
-
switch
on the ignition.
The
display begins a countdown.
When the display shows "=0", release
the
button; the spanner disappears.
Instruments and controls
