2013 YAMAHA YFZ450 Owners Manual

8-15
8
To check the engine oil level
1. Place the ATV on a level surface.
2. Start the engine, warm it up until the engine oil has reached a normal temperature of 40 °C
(104 °F), let it continue to idle for ten seconds
or more, and then turn the engine off.
TIPTo achieve the proper engine oil temperature for
an accurate oil level reading, the engine must have
first completely cooled down, and then warmed up
again for several minutes to normal operating tem-
perature.3. Remove the engine oil tank filler cap, and thenwipe the engine oil dipstick off with a clean
rag.
4. Insert the dipstick into the filler hole (without screwing it in), and then remove it again to
check the oil level.
TIPThe engine oil should be between the minimum
and maximum level marks.5. If the engine oil is at or below the minimumlevel mark, add sufficient oil of the recom-
mended type through the engine oil tank filler
hole to raise it to the correct level. NOTICE:1. Engine oil tank filler cap
2. Engine oil dipstick
3. Engine oil tank
4. Crankcase engine oil filler cap
5. Maximum level mark
6. Minimum level mark
4
3
1
1
2
5
6
U1PD61E0.book Page 15 Tuesday, February 14, 2012 10:06 AM

8-16
8Be sure the engine oil is at the correct lev-
el, otherwise engine damage may result.
[ECB00851]
TIPWhen adding oil, be careful not to overfill the en-
gine oil tank; the oil level rises faster starting from
the half-level-portion on the dipstick.6. Insert the dipstick into the engine oil tank filler
hole, and then tighten the engine oil tank filler
cap. NOTICE: Make sure that the engine oil
tank filler cap is securely tightened; other-
wise, oil may seep out when the engine is
running.
[ECB00362]
To change the engine oil (with or without oil fil-
ter element replacement) 1. Place the ATV on a level surface.
2. Remove the engine guard by removing the bolts. 3. Start the engine, warm it up for several min-
utes, and then turn it off.
4. Place an oil pan under the engine to collect the used oil.
5. Remove the crankcase engine oil filler cap, and the crankcase engine oil drain bolt and its
gasket.
1. Engine guard
2. Bolt
1
2
U1PD61E0.book Page 16 Tuesday, February 14, 2012 10:06 AM

8-17
8
6. Remove the engine oil tank filler cap, and the
engine oil tank drain bolt and its gasket.
TIPSkip steps 7–10 if the oil filter element is not being
replaced.7. Remove the oil filter element cover by remov-ing the bolts.
1. Crankcase engine oil drain bolt
2. Gasket
2
1
1. Engine oil tank drain bolt
2. Gasket
12
U1PD61E0.book Page 17 Tuesday, February 14, 2012 10:06 AM

8-18
88. Remove the oil filter element and the O-rings. 9. Install a new oil filter element and new O-
rings.
TIPMake sure that the O-rings are properly seated.10. Install the oil filter element cover by installing the bolts, and then tighten them to the speci-
fied torque.
11. Install the crankcase engine oil drain bolt, the engine oil tank drain bolt and their new gasket,
and then tighten the bolts to the specified
torques.
1. Oil filter element cover
2. Bolt
1. Oil filter element
2. O-ring
1
21
2
2
Tightening torque:
Oil filter element cover bolt:10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tightening torques: Crankcase engine oil drain bolt:20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil tank drain bolt: 19 Nm (1.9 m·kgf, 14 ft·lbf)
U1PD61E0.book Page 18 Tuesday, February 14, 2012 10:06 AM

8-19
8
12. Refill with the specified amount of the recom-
mended engine oil through the engine oil tank
filler hole, and then install and tighten the en-
gine oil tank filler cap.
13. Refill with the specified amount of the recom- mended engine oil through the crankcase en-
gine oil filler hole, and then install and tighten
the crankcase engine oil filler cap.
TIPBe sure to wipe off spilled oil on any parts after the
engine and exhaust system have cooled down.NOTICEECB00300●In order to prevent clutch slippage (since the
engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of
a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV-
ING II” or higher.●Make sure that no foreign material enters the
crankcase.14. Start the engine, and then let it idle for severalminutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.
15. Turn the engine off, and then check the oil lev- el and correct it if necessary.
Recommended oil:
See page 10-1.
Oil quantity: Without oil filter element replacement:Quantity in oil tank: 1.55 L (1.64 US qt, 1.36 Imp.qt)
Quantity in crankcase: 0.20 L (0.21 US qt, 0.18 Imp.qt)
With oil filter element replacement: Quantity in oil tank: 1.55 L (1.64 US qt, 1.36 Imp.qt)
Quantity in crankcase: 0.30 L (0.32 US qt, 0.26 Imp.qt)
U1PD61E0.book Page 19 Tuesday, February 14, 2012 10:06 AM

8-20
816. Install the engine guard by installing the bolts,
and then tighten them to the specified torque.
NOTICE: Be sure to apply LOCTITE
® to the
engine guard bolts before installing them.
[ECB00371]
EBU23470
Coolant The coolant level should be checked before each
ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.EBU27942To check the coolant level 1. Place the ATV on a level surface.TIPThe coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.2. Check the coolant level in the coolant reser- voir.
TIPThe coolant should be between the minimum and
maximum level marks.3. If the coolant is at or below the minimum levelmark, remove the coolant reservoir cap, add
coolant or distilled water to the maximum level
mark, and then install the reservoir cap.
NOTICE: If coolant is not available, use
distilled water or soft tap water instead. Do
not use hard water or salt water since they
Tightening torque:
Engine guard bolt:7 Nm (0.7 m·kgf, 5.1 ft·lbf)1. Maximum level mark
2. Minimum level mark
3. Coolant reservoir
4. Coolant reservoir cap
1
2 4
3
U1PD61E0.book Page 20 Tuesday, February 14, 2012 10:06 AM

8-21
8
are harmful to the engine. If water has
been used instead of coolant, replace it
with coolant as soon as possible, other-
wise the cooling system will not be pro-
tected against frost and corrosion. If water
has been added to the coolant, have a
Yamaha dealer check the antifreeze con- tent of the coolant as soon as possible,
otherwise the effectiveness of the coolant
will be reduced.
[ECB01011]
TIP●The radiator fan is automatically switched on or
off according to the coolant temperature in the
radiator.●If the engine overheats, see page 8-58 for fur-
ther instructions.
EBU23564To change the coolant
WARNING
EWB01890Wait for the engine and radiator to cool before
removing the radiator cap. You could be
burned by hot fluid and steam blown out under
pressure. Always place a thick rag over the cap
when opening. Allow any remaining pressure
to escape before completely removing the cap.1. Place the ATV on a level surface.
2. Remove panel A. (See page 8-9.)
3. Place a container under the engine, and then remove the coolant drain bolt and its gasket.
(Use a trough or a similar object as shown.)
Coolant reservoir capacity (up to the maxi-
mum level mark):
0.29 L (0.31 US qt, 0.26 Imp.qt)
U1PD61E0.book Page 21 Tuesday, February 14, 2012 10:06 AM

8-22
84. Remove the radiator cap. 5. Remove the coolant reservoir by removing the
bolts.
6. Remove the coolant reservoir cap, and then turn the coolant reservoir upside down to
empty it.
1. Coolant drain bolt
2. Gasket
3. Trough
3
2
1
1. Radiator cap
1
U1PD61E0.book Page 22 Tuesday, February 14, 2012 10:06 AM