Page 13 of 98
2-1
12
DESCRIPTION
EAU10410
Left view
12
1, 23
4, 5 6
7810
9
11
1. Front fork compression damping force adjusting screw (page 3-14)
2. Bleed screw (page 3-15)
3. Starter knob (page 3-12)
4. Battery (page 6-30)
5. Main fuse (page 6-32)
6. Air filter element (page 6-14)
7. Engine oil check bolt (page 6-8) 8. Shift pedal (page 3-8)
9. Engine oil filler cap (page 6-8)
10.Engine oil drain bolt
(oil tank) (page 6-8)
11.Engine oil dipstick (page 6-8)
12.Front fork rebound damping force adjusting screw (page 3-14)
1DX-9-E1.book 1 ページ ２０１２年７月３１日 火曜日 午前９時３１分
Page 14 of 98
DESCRIPTION
2-2
12
3
4
5
6
7
8
9
EAU10420
Right view
1, 23 5
7
8
11
6
10
12
9 4
1. Shock absorber assembly comp
ression damping force adjusting
screw (for slow compression damping) (page 3-16)
2. Shock absorber assembly compression damping force adjusting nut (for fast compression damping) (page 3-16)
3. Kickstarter (page 3-12)
4. Fuel tank cap (page 3-9)
5. Radiator cap (page 6-12)
6. Steering lock (page 3-13) 7. Coolant drain bolt (page 6-13)
8. Brake pedal (page 3-9)
9. Engine oil drain bolt (crankcase) (page 6-8)
10.Rear brake fluid reservoir (page 6-23)
11.Shock absorber assembly reboun
d damping force adjusting screw
(page 3-16)
12.Rear brake light switch (page 6-22)
1DX-9-E1.book 2 ページ ２０１２年７月３１日 火曜日 午前９時３１分
Page 53 of 98
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
2
3
4
567
8
9
6. Install the engine oil tank cap, and
then the check bolt and its gasket.
To change the engine oil (with or
without oil filter element replace-
ment) 1. Place the vehicle on a level sur- face.
2. Start the engine, warm it up for several minutes, and then turn it
off.
3. Place an oil pan under the engine to collect the used oil.
4. Remove the engine guard by re- moving the bolts.
5. Remove the engine oil tank cap and the engine oil filler cap.
6. Remove the engine oil drain bolts and their gasket to drain the oil
from the oil tank and crankcase. 7. Remove the engine oil filter ele-
ment drain bolt and gasket to drain
the oil from the oil filter element.
1. Bolt
2. Engine guard2
1
1
1. Engine oil tank cap
2. Engine oil filler cap
1. Engine oil drain bolt (oil tank)
2. Gasket
1
2
21
1. Engine oil drain bolt (crankcase)
2. Gasket
1. Oil filter element drain bolt
2. Gasket
2121
1DX-9-E1.book 10 ページ ２０１２年７月３１日 火曜日 午前９時３１分
Page 54 of 98
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
1
2
3
4
56
7
8
9
TIPSkip steps 8–10 if the oil filter elementis not being replaced.8. Remove the oil filter element cover by removing the bolts.
9. Remove and replace the oil filter element and O-rings. 10. Install the oil filter element cover by
installing the bolts, and then tight-
en the bolts to the specified torque.
TIPMake sure that the O-rings are properlyseated.
11. Install the engine oil drain bolts and their new gasket, and then
tighten the bolts to the specified
torques. 12. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the engine
oil tank cap and the oil filler cap.
TIPBe sure to wipe off spilled oil on any
parts after the engine and exhaust sys-tem have cooled down.NOTICE
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
1. Oil filter element cover
2. Oil filter element cover bolt
1
2
1. Oil filter element cover
2. Oil filter element
3. O-ringTightening torque:Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)1 2
3
3
3
Tightening torques: Engine oil drain bolt (oil tank):20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil drain bolt (crank case):
20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil filter element drain bolt: 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Recommended engine oil: See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:0.95 L (1.00 US qt, 0.84 Imp.qt)
With oil filter element replacement: 1.00 L (1.06 US qt, 0.88 Imp.qt)
1DX-9-E1.book 11 ページ ２０１２年７月３１日 火曜日 午前９時３１分
Page 56 of 98
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
1
2
3
4
56
7
8
9
TIPThe coolant should be at the bottom of
the radiator filler neck. The level will
change with variation of engine temper-ature.3. If the coolant is below the correct
coolant level, add coolant, and
then install the radiator cap.
NOTICE: If coolant is not avail-
able, use distilled water or soft
tap water instead. Do not use
hard water or salt water since it
is harmful to the engine. If water
has been used instead of cool-
ant, replace it with coolant as
soon as possible, otherwise the
cooling system will not be pro-
tected against frost and corro-
sion. If water has been added to
the coolant, have a Yamaha
dealer check the antifreeze con-
tent of the coolant as soon as
possible, otherwise the effec-
tiveness of the coolant will be
reduced.
[ECA10472]
EAUM1315
To change the coolant 1. Place the vehicle on a level sur- face and let the engine cool if nec-
essary.
2. Place a container under the engine to collect the used coolant.
3. Remove the coolant drain bolt and its gasket, and then the radiator
cap to drain the cooling system.
WARNING! Never attempt to re-
move the radiator cap when the
engine is hot.
[EWA10381]
4. After the coolant is completely drained, thoroughly flush the cool-
ing system with clean tap water.
5. Install the coolant drain bolt and its new gasket, and then tighten the
bolt to the specified torque.
6. Pour the recommended coolant
1. Radiator cap
1. Radiator filler neck
2. Correct coolant level
1
2
1
1. Coolant drain bolt
2. GasketTightening torque:
Coolant drain bolt:10 Nm (1.0 m·kgf, 7.2 ft·lbf)
21
1DX-9-E1.book 13 ページ ２０１２年７月３１日 火曜日 午前９時３１分
