2013 YAMAHA GRIZZLY 125 oil type

8-12
8
TIPThe engine oil should be between the minimum
and maximum level marks.5. If the engine oil is at or below the minimumlevel mark, add sufficient oil of the recom-
mended type to raise it to the correct level.
NOTICE: Be sure the engine oil is at the
correct level, otherwise engine damage
may result.
[ECB00851]
6. Insert the dipstick into the oil filler hole, and then tighten the engine oil filler cap. To change the engine oil
1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min- utes, and then turn it off.
3. Place an oil pan under the engine to collect the used oil.
4. Remove the engine oil filler cap, and then re- move the engine oil drain bolt to drain the oil
from the crankcase. NOTICE: When remov-
ing the engine oil drain bolt, the compres-
sion spring, oil strainer and O-ring will fall
out. Take care not to lose these parts.
[ECB00311]
1. Maximum level mark
2. Minimum level mark
12
U1PY61E0.book Page 12 Wednesday, March 14, 2012 5:22 PM

8-15
85. Pour the recommended type of oil in the trans-
mission oil filler hole until it flows out of the
check screw hole.
6. Tighten the oil check screw to the specified torque.
7. Check the oil filler bolt gasket for damage, and replace it if necessary. 8. Install the transmission oil filler bolt and its
gasket, and then tighten the bolt to the speci-
fied torque.
To change the transmission oil 1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min- utes, and then turn it off.
3. Place an oil pan under the transmission to col- lect the used oil.
4. Remove the transmission oil filler bolt, the transmission oil drain bolt and their gasket to
drain the oil from the transmission case.
1. Transmission oil filler bolt
2. GasketTightening torque:Transmission oil check screw:16 Nm (1.6 m·kgf, 12 ft·lbf)
1
2
Tightening torque: Transmission oil filler bolt:23 Nm (2.3 m·kgf, 17 ft·lbf)
U1PY61E0.book Page 15 Wednesday, March 14, 2012 5:22 PM

10-1
10
EBU25961
SPECIFICATIONS
Dimensions:Overall length:1700 mm (66.9 in)
Overall width: 990 mm (39.0 in)
Overall height:
980 mm (38.6 in)
Seat height: 685 mm (27.0 in)
Wheelbase: 1080 mm (42.5 in)
Ground clearance:
145 mm (5.7 in)
Minimum turning radius: 2900 mm (114 in)Weight:With oil and fuel:
152.0 kg (335 lb)Noise and vibration level:Noise level (77/311/EEC):78.0 dB(A)@3500 r/min
Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s²
Vibration on handlebar (EN1032, ISO5008): Will not exceed 2.5 m/s²Engine:Engine type:
Air cooled 4-stroke, SOHC Cylinder arrangement:
Single cylinder
Displacement: 124 cm³
Bore × stroke:
49.0 × 66.0 mm (1.93 × 2.60 in)
Compression ratio:
9.00 : 1
Starting system: Electric starter
Lubrication system: Wet sump
Engine oil:Recommended brand:YAMALUBE
U1PY61E0.book Page 1 Wednesday, March 14, 2012 5:22 PM

10-2
10
Type:SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Engine oil quantity: Periodic oil change:
1.25 L (1.32 US qt, 1.10 Imp.qt)Transmission oil:Quantity:0.6 L (0.63 US qt, 0.53 Imp.qt)Air filter:Air filter element:Wet element
Fuel:Recommended fuel:Regular unleaded gasoline only
Fuel tank capacity:
7.0 L (1.85 US gal, 1.54 Imp.gal)
Fuel reserve amount: 1.3 L (0.34 US gal, 0.29 Imp.gal)Carburetor:Type × quantity:
VM18SH x 1Spark plug (s):Manufacturer/model: NGK/CR7HSA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)Clutch:Clutch type:Dry, centrifugal automaticTransmission:Primary reduction system:Helical gear/spur gear
Primary reduction ratio: 43/14 × 40/17 (7.226)
Secondary reduction system:
Chain drive
Secondary reduction ratio: 32/12 (2.666)
Transmission type: V-belt automatic
Operation:
Centrifugal automatic type
-20 -10 0 1020 30
4050 C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30
U1PY61E0.book Page 2 Wednesday, March 14, 2012 5:22 PM

10-4
10
Spring/shock absorber type:Coil spring/oil damper
Wheel travel: 70 mm (2.8 in)Rear suspension:Type:Swingarm
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
80 mm (3.1 in)Electrical system:Ignition system:DC CDI
Charging system:
AC magnetoBattery:Model:12N12C-4A-2
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 1
Neutral indicator light:
12 V, 1.7 W × 1 Reverse indicator light:
12 V, 1.7 W × 1
Fuses:Main fuse:
15.0 AEBU30401For Europe only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
U1PY61E0.book Page 4 Wednesday, March 14, 2012 5:22 PM