2013 YAMAHA GRIZZLY 125 Owners Manual

8-34
8
3. If the correct free play cannot be obtained as
described above, turn the adjusting bolt fully in
direction (a), and then adjust the free play us-
ing the brake lever free play adjusting nut on
the rear wheel hub.
4. Turn the brake lever free play adjusting nut on the rear wheel hub in direction (a) to increase
the free play, and in direction (b) to decrease
it. 5. Use the adjusting bolt to obtain a precise ad-
justment if necessary, and then tighten the
locknut. If the correct free play cannot be ob-
tained, have a Yamaha dealer adjust it.
EBU24874Drive chain slack The drive chain slack should be checked before
each ride and adjusted if necessary.
To check the drive chain slack1. Place the ATV on a level surface.
1. Locknut
2. Brake lever free play adjusting bolt
(a)
(b) 2
1
1. Brake lever free play adjusting nut
1
(a)
(b)
U1PY61E0.book Page 34 Wednesday, March 14, 2012 5:22 PM

8-35
8
TIPWhen checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.2. Move the ATV back and forth to locate thetightest portion of the drive chain, and then
measure the drive chain slack as shown.
3. If the drive chain slack is incorrect, adjust it as follows. To adjust the drive chain slack
1. Place the ATV on a level surface.
2. Loosen the hub stopper bolt locknut and then the hub stopper bolt.
3. Loosen the axle holding bolts.
4. Loosen the drive chain slack adjusting bolt locknut. To tighten the drive chain, turn the ad-
justing bolt in direction (a). To loosen the drive
chain, turn the adjusting bolt in direction (b),
and then push the wheels forward. NOTICE:
Improper drive chain slack will overload
Drive chain slack:
30.0 mm (1.18 in)1. Drive chain slack
1
1. Hub stopper bolt
2. Hub stopper bolt locknut
3. Axle holding bolt (lower)
4. Axle holding bolt (upper)1 2
34
U1PY61E0.book Page 35 Wednesday, March 14, 2012 5:22 PM

8-36
8
the engine as well as other vital parts of
the ATV and can lead to drive chain slip-
page or breakage. To prevent this from oc-
curring, keep the drive chain slack within
the specified limits.
[ECB00542]
5. Tighten the drive chain slack adjusting bolt
locknut and the axle holding bolts to the spec-
ified torques.
NOTICEECB00551If measurement “A” of the drive chain slack ad-
justing bolt is less than 27 mm (1.06 in), have a
Yamaha dealer replace the drive chain.
1. Locknut
2. Drive chain slack adjusting bolt
1
2
(a)
(b)
Tightening torques:
Drive chain slack adjusting bolt locknut:16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle holding bolt (upper): 85 Nm (8.5 m·kgf, 61 ft·lbf)
Axle holding bolt (lower): 60 Nm (6.0 m·kgf, 43 ft·lbf)1. Measurement A
1
U1PY61E0.book Page 36 Wednesday, March 14, 2012 5:22 PM

8-37
86. Tighten the hub stopper bolt and hub stopper
bolt locknut to the specified torques.
EBU24882Lubricating the drive chain The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.NOTICEECB00561The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.1. Clean the drive chain with kerosene and asmall soft brush. NOTICE: To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain lubricant. NOTICE: Do
not use engine oil or any other lubricants
for the drive chain, as they may contain
substances that could damage the O-
rings.
[ECB00581]
EBU24902
Checking and lubric ating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
Tightening torques:
Hub stopper bolt:16 Nm (1.6 m·kgf, 12 ft·lbf)
Hub stopper bolt locknut: 16 Nm (1.6 m·kgf, 12 ft·lbf)1. O-ring
1
1
U1PY61E0.book Page 37 Wednesday, March 14, 2012 5:22 PM

8-38
8
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.
WARNING
EWB02581●Inspect cables frequently and replace if dam-
aged. Corrosion can result when the cable
sheaths become damaged, and cables can
also become frayed or kinked, which could
restrict the operation of controls and lead to
an accident or injury.●Always make sure all control cables work
smoothly before you begin riding in cold
weather. If the control cables are frozen or do
not work smoothly, you could be unable to
control the ATV, which could lead to an acci-
dent or collision.
EBU28702Checking and lubric
ating the front and
rear brake levers The operation of the front and rear brake levers
should be checked before each ride, and the lever
pivots should be lubricated if necessary.
Front brake lever
Recommended lubricant:
Yamaha Chain and Cable Lube or engine oilRecommended lubricant: Lithium-soap-based grease
U1PY61E0.book Page 38 Wednesday, March 14, 2012 5:22 PM

8-39
8Rear brake lever
EBU24963Checking the wheel hub bearings The front and rear wheel hub bearings must be
checked at the intervals specified in the periodic
maintenance and lubrication chart. If there is play
in a wheel hub or if a wheel does not turn smoothly,
have a Yamaha dealer check the wheel hub bear-
ings.
EBU30380Lubricating the lower arm pivots The lower arm pivots must be lubricated at the in-
tervals specified in the periodic maintenance and
lubrication chart.TIPFor parts equipped with a grease nipple, use a
grease gun.Recommended lubricant:
Lithium-soap-based grease
U1PY61E0.book Page 39 Wednesday, March 14, 2012 5:22 PM

8-40
8
Left side
Right side
EBU28823Lubricating the front
knuckle pivots The front knuckle pivots must be lubricated at the
intervals specified in the periodic maintenance and
lubrication chart.TIPFor parts equipped with a grease nipple, use a
grease gun.
1. Grease nipple
1. Grease nipple
111
1
Recommended lubricant:Lithium-soap-based grease1. Grease nipple
1
U1PY61E0.book Page 40 Wednesday, March 14, 2012 5:22 PM

8-41
8
EBU25092Lubricating the steering shaft The steering shaft must be lubricated by a Yamaha
dealer at the intervals specified in the periodic
maintenance and lubrication chart.TIPFor parts equipped with a grease nipple, use a
grease gun.
EBU2512ABattery The battery is located under the seat. (See page
4-10.)
A poorly maintained battery will corrode and dis-
charge quickly. The electrolyte level, battery lead
connections and breather hose routing should be
checked before each ride and at the intervals
specified in the periodic maintenance and lubrica-
tion chart.
WARNING
EWB02160Battery electrolyte is poisonous and danger-
ous, as it contains sulfuric acid, which can
cause severe burns. Avoid contact with skin,
eyes or clothing. Always shield your eyes
when working near batteries.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten egg
or vegetable oil. Call a physician immediately.
EYES: Flush with water for 15 minutes and get
prompt medical attention.
Recommended lubricant:
Lithium-soap-based grease
1. Grease nipple
1
U1PY61E0.book Page 41 Wednesday, March 14, 2012 5:22 PM