2013 VOLKSWAGEN PASSAT light

WARNING
Improper replacement of burned out headlights and other light bulbs can cause serious
personal injury.
x Stop! Always read and heed the WARNINGS before doing any work in the engine
compartment. The engine compartment of any motor vehicle is a potentially dangerous area,
and work in this area can lead to serious personal injury.
x HID – High Intensity Discharge (Xenon) headlights get power from a high voltage source
that can cause severe personal injury and even death if handled improperly.
x H7 bulbs and HID – High Intensity Discharge (Xenon) headlights are under high pressure
and can explode if handled improperly.
x Always let a burned out light bulb cool down before replacing it.
x Never replace a light bulb unless you are familiar with all of the necessary procedures. In
particular, never remove a headlight unless you know exactly how to carry out the job and
have the correct tools and light bulbs.
x If you are uncertain about what to do, have the work performed by an authorized
Volkswagen dealer, an authorized Volkswagen Service Facility, or another qualified
workshop. Serious personal injury may result from improperly performed work.
x We strongly recommend that you always have HID – High Intensity Discharge (Xenon)
headlights and H7 bulbs replaced by a qualified technician.
x Do not touch the glass of light bulbs with your bare hands. Fingerprints left on the bulb
evaporate due to the heat when the bulb is switched on and cause the reflector to “cloud.”
x There are sharp edges on and around the headlight housing in the engine compartment
and the rear light housing. Wear hand protection if you replace bulbs.
NOTICE
After replacing a headlight bulb or other light bulb, always make sure that the rubber covers or
plastic caps have been properly and securely reinstalled to help prevent water from getting
into the electrical connections and headlight housing and damaging the electrical system.
Indicator light

NOTICE
Failure to heed warning lights or text WARNINGS can result in vehicle damage.
Information on light bulb replacement

Replacing headlight bulbs

Fig. 216 In the engine compartment: Covers in the left headlight assembly: A Side marker light, B Low beam
headlight, C High beam headlight,>Turn signal and parking light, E Daytime running light.

Fig. 217 In the wheel housing: Removing cover.

⇒ fig. 216 (A) (B) (C) (D) (E)
Side marker
light
Low beam High beam Turn signal
and parking
light
Daytime
running lights
3.
Unscrew the
fastening screw
⇒ fig. 217
(arrow) with a
short
screwdriver. To
access the
screw, turn the
wheel in
question inward
as shown in .

Same as column
(A).
4.
Remove the
cover from the
wheel house
lining .
Same as column
(A).
5. On the back of the headlight assembly, pull off the rubber cover for
the bulb you are replacing.
Turn plastic
cover ⇒ fig. 216
A (E)
counterclockwise
and remove.
6. Left side of the
vehicle: Turn
plastic bulb
socket
counterclockwise
(about 1/8 turn)
to release it.
Right side of the
vehicle: Turn
plastic bulb
socket clockwise
(about 1/8 turn)
instead.
Turn plastic bulb
socket
counterclockwise
(about 1/8 turn)
to release it.
Press plastic
tab on back of
bulb socket to
release it.
Same as
column (A).
Same as column
(A).
7. Pull plastic bulb socket assembly back and out of the headlight assembly.
8. Replace the burned out light bulb with a new bulb of the same type.
9. Reinsert the bulb socket assembly into the headlight assembly.

⇒ fig. 216 (A) (B) (C) (D) (E)
Side marker
light
Low beam High beam Turn signal
and parking
light
Daytime
running lights
10. Left side of the
vehicle: Turn
plastic bulb
socket clockwise
until it locks into
place in the
headlight
assembly.
Right side of the
vehicle: Turn
plastic bulb
socket
counterclockwise
instead.
Turn plastic bulb
socket clockwise
until it locks into
place in the
headlight
assembly.
Push bulb
socket into
the headlight
assembly
until you hear
it “click” into
place.
Same as
column (A).
Same as column
(A).
11. Replace rubber cover on the back of the headlight assembly for the
bulb you replaced.
Place the plastic
cover A (E) in
the headlight
assembly
housing and turn
clockwise as far
as it will go.
12.
Place the cover
⇒ fig. 217 in the
wheel housing
liner and use the
screwdriver in
the vehicle tool
kit to tighten the
fastening screw
(arrow).

Same as column
(A).
Please carry out each step only in the order specified:
The illustrations show the left headlight assembly from the rear. The right headlight assembly is
the mirror image of the left headlight assembly.

Replacing taillight bulbs in the luggage compartment lid

Fig. 220 A: In the luggage compartment lid: Removing the taillight cover. B: Removing the taillight assembly.

Fig. 221 A: Taillight assembly: removing the bulb socket assembly. B: Removing the light bulbs.

Please carry out each step only in the order specified:
9. Replace the burned out light bulb with a new bulb of the same type B.
10. Reinsert the bulb socket assembly in the taillight assembly. The locking tabs must latch
with an audible “click.”
11.
Carefully reinsert the taillight assembly into the opening in the luggage compartment lid.
Hold the rear light assembly with one hand in the installation position, and with the other
hand tighten the fastening screws ⇒ fig. 220 B (3).
12. Plug connector plug B (2) into the bulb socket and push red locking tab B (4) in the
direction opposite to the arrow.
13. Check the taillight assembly for proper installation and secure fit.
14. Attach the cover. The cover must latch tightly and securely into place.
15. Close the luggage compartment lid.

Different models may have different taillights, and the light bulb may be in a different location
than shown in the illustrations.

As the driver of the towing vehicle:
x Drive especially carefully and accelerate gently. Avoid sudden driving maneuvers.
x Brake earlier and more gently than usual and with light pedal pressure.
x Read and heed the information and WARNINGS in the owner's manual of the vehicle being towed.