2013 TOYOTA xD bulb

TABLE OF CONTENTSIndex
4
Scion_xD_OM_OM52C62U_(U)
4-1. Maintenance and careCleaning and protecting the vehicle exterior ........... 216
Cleaning and protecting the vehicle interior ............ 219
4-2. Maintenance Maintenance requirements .................... 222
General maintenance ......... 225
Emission inspection and maintenance (I/M)
programs .......................... 229
4-3. Do-it-yourself maintenance Do-it-yourself service precautions ...................... 230
Hood................................... 233
Positioning a floor jack ....... 235
Engine compartment .......... 237
Tires ................................... 252
Tire inflation pressure......... 261
Wheels ............................... 265
Air conditioning filter (for Puerto Rico) ............... 268
Wireless remote control battery .............................. 271
Checking and replacing fuses ................................ 273
Light bulbs .......................... 284 5-1. Essential information
Emergency flashers ............ 294
If your vehicle needs to be towed ....................... 295
If you think something is wrong ................................ 302
Fuel pump shut off system .............................. 303
5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer
sounds .............................. 304
If you have a flat tire ........... 318
If the engine will not start ............................ 332
If the shift lever cannot be shifted from P (automatic
transmission) .................... 333
If you lose your keys ........... 334
If you cannot operate the back door opener ....... 335
If the vehicle battery is discharged ........................ 336
If your vehicle overheats .......................... 341
If the vehicle becomes stuck ................................. 344
If your vehicle has to be stopped in an
emergency ........................ 346
4Maintenance and care5When trouble arises

138
2-1. Driving procedures
Scion_xD_OM_OM52C62U_(U)
Tur n signal lever
■Turn signals can be operated when
The engine switch is in the
“ON” position.
■ If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
The turn signal lever can be used to show the following intentions
of the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
The right hand signal will flash
until you release the lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signal will flash
until you release the lever.

Maintenance and care4
215
Scion_xD_OM_OM52C62U_(U)
4-1. Maintenance and careCleaning and protecting the vehicle exterior......... 216
Cleaning and protecting the vehicle interior.......... 219 4-2. Maintenance
Maintenance requirements .................. 222
General maintenance....... 225
Emission inspection and maintenance (I/M)
programs ........................ 229
4-3. Do-it-yourself maintenance Do-it-yourself service precautions .................... 230
Hood ................................ 233
Positioning a floor jack ..... 235
Engine compartment ........ 237
Tires ................................. 252
Tire inflation pressure ...... 261
Wheels ............................. 265
Air conditioning filter (for Puerto Rico) ............ 268
Wireless remote control battery ............................ 271
Checking and replacing fuses .............................. 273
Light bulbs........................ 284

231
4-3. Do-it-yourself maintenance
4
Maintenance and care
Scion_xD_OM_OM52C62U_(U)
ItemsParts and tools
Engine oil level
P. 238)
• “Toyota Genuine Motor Oil” or
equivalent
• Rag or paper towel
• Funnel (used only for adding engine oil)
Fuses (P. 273)• Fuse with same amperage rating
as original
Light bulbs (P. 284)
• Bulb with same number and watt-
age rating as original
• Flathead screwdriver
Radiator and condenser (P. 245)
Tire inflation pressure ( P. 261)• Tire pressure gauge
• Compressed air source
Washer fluid (P. 250)
• Water or washer fluid containing
antifreeze (for winter use)
• Funnel (used only for adding water or washer fluid)

283
4-3. Do-it-yourself maintenance
4
Maintenance and care
Scion_xD_OM_OM52C62U_(U)
■
After a fuse is replaced
● If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. ( P. 284)
● If the replaced fuse blows again, have the vehicle inspected by your
Scion dealer.
■ If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
■To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage to the vehicle, and possibly a fire or
injury.
● Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
● Always use a genuine Scion fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
● Do not modify the fuse or the fuse box.
NOTICE
■Before replacing fuses
Have the cause of electrical overload determined and repaired by your Scion
dealer, as soon as possible.

284
4-3. Do-it-yourself maintenance
Scion_xD_OM_OM52C62U_(U)
Light bulbs
You may replace the following bulbs yourself. The difficulty level of
replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your Scion dealer.
For more information about replacing other light bulbs, contact your
Scion dealer.
■ Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. ( P. 360)
■ Front bulb locations
Front turn signal light
Front side
marker light
Daytime running light
and headlight
Parking light

285
4-3. Do-it-yourself maintenance
4
Maintenance and care
Scion_xD_OM_OM52C62U_(U)
■
Rear bulb locations
Back-up light
License plate lights
Stop/tail and
rear side
marker light
Rear turn signal light

286 4-3. Do-it-yourself maintenance
Scion_xD_OM_OM52C62U_(U)
Replacing light bulbs■ Headlights and daytime running lights (for Canada)
Unplug the connector and
remove the rubber cover.
Release the bulb retaining
spring.
Remove the bulb.
To install a new bulb, align the
tabs of the bulb with the cutouts
of the mounting hole.
STEP 1
STEP 2
STEP 3