2013 TOYOTA IQ Owners Manual

257
4-3. Do-it-yourself maintenance
4
Maintenance and care
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
■ Parking/front side marker lights
Turn the bulb base counterclock-
wise.

258 4-3. Do-it-yourself maintenance
Remove the light bulb.
■ Front turn signal lights
Turn the bulb base counterclock-
wise.
Remove the light bulb.

259
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Back-up lights, stop/tail and rear side marker lights and rear
turn signal lights
Open the back door. ( P. 31)
Folding down rear seatbacks. ( P. 3 8 )
Remove the cover.
Use a flathead screwdriver which
is wrapped with a cloth.
Turn the bulb bases counter-
clockwise.
Stop/tail and rear side marker
light
Rear turn signal light
Back-up light
Remove the light bulb. Stop/tail and rear side marker
light
Rear turn signal light
Back-up light

260 4-3. Do-it-yourself maintenance
■License plate lights
Disengage the claws.
Use a flathead screwdriver which
is wrapped with a cloth.
Remove the license plate light.
Turn the bulb base counterclock-
wise.
Remove the light bulb.

261
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Lights other than the above
If any of the lights listed below has burned out, have it replaced by
your Scion dealer.
● Side turn signal lights
● High mounted stoplight
■When replacing the left side headlight
Be sure to install the fuse cover properly.
■ Condensation build-up on th e inside of the lens
Contact your Scion dealer for more information in the following situations.
● Large drops of water are built up on the inside of the lens.
● Water has built up inside the headlight.
Temporary condensation build-up on the inside of the headlight lens does
not indicate a malfunction.
■ LED high mounted stoplight
The high mounted stoplight consists of a number of LEDs. If any of the LEDs
burn out, take your vehicle to your Scion dealer to have the light replaced.
CAUTION
■Replacing light bulbs
●Turn off the headlights. Do not attempt to replace the bulb immediately
after turning off the headlights.
The bulbs become very hot and may cause burns.
● Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped it may blow out or crack.
● Fully install light bulbs and any parts used to secure them. Failing to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
■ To prevent damage or fire
Make sure bulbs are fully seated and locked.

262 4-3. Do-it-yourself maintenance

When trouble arises5
263
5-1. Essential informationEmergency flashers ......... 264
If your vehicle needs to be towed ........................ 265
If you think something is wrong ............................. 271
Fuel pump shut off system ........................... 272 5-2. Steps to take in
an emergency
If a warning light turns on or a warning buzzer
sounds... ........................ 273
If you have a flat tire......... 284
If the engine will not start ................................ 301
If the shift lever cannot be shifted from P............ 303
If you lose your keys ........ 304
If the vehicle battery is discharged ..................... 305
If your vehicle overheats ....................... 308
If the vehicle becomes stuck .............................. 311
If your vehicle has to be stopped in
an emergency ................ 313

264
5-1. Essential information
Emergency flashers
NOTICE
■To prevent battery discharge
Do not leave the emergency flashers on longer than necessary when the
engine is not running.
Use the emergency flashers if th e vehicle malfunctions or is
involved in an accident.
Press the switch to flash all
the turn signal lights. To turn
them off, press the switch
once again.