7-13
INSPECTION AND MAINTENANCE
53MH0-74E
Refill with Oil and Check for Leaks
1) Pour oil through the filler hole and
install the filler cap.
For the approximate capacity of the oil,
refer to the “Capacities” item in the
“SPECIFICATIONS” section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait about 5 min-
utes. Check the oil level again and add
oil if necessary. Check for leaks again.
Engine Coolant
Selection of Coolant
To maintain optimum performance and
durability of your engine, use MARUTI
Genuine Coolant or equivalent.
This type of coolant is best for your cooling
system as it:
Helps maintain proper engine tempera-
ture.
Gives proper protection against freezing
and boiling.
Gives proper protection against corro-
sion and rust.
Failure to use the proper coolant can dam-
age your cooling system. Your authorized
MARUTI SUZUKI dealer can help you
select the proper coolant.
Coolant Level Check
Check the coolant level at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
the “FULL” and “LOW” marks.
NOTICE
• When replacing the oil filter, it is rec-
ommended that you use a genuine
MARUTI SUZUKI replacement filter.
If you use an aftermarket filter, make
sure it is of equivalent quality and
follow the manufacturer’s instruc-
tions.
• Oil leaks from around the oil filter
or drain plug indicate incorrect
installation or gasket damage. If
you find any leaks or are not sure
that the filter has been properly
tightened, have the vehicle
inspected by your MARUTI SUZUKI
dealer.
NOTICE
To avoid damaging your cooling sys-
tem:
• Always use a high quality eth-
yleneglycol base non-silicate type
coolant diluted with distilled water
at the correct mixture concentra-
tion.
• Make sure that the proper mix is 30/
70 coolant to distilled water and in
no case higher than 70/30. Concen-
trations greater than 70/30 coolant
to distilled water will cause over-
heating conditions.
• Do not use straight coolant nor
plain water.
• Do not add extra inhibitors or addi-
tives. They may not be compatible
with your cooling system.
• Do not mix different types of base
coolants. Doing so may result in
accelerated seal wear and/or the
possibility of severe overheating
and extensive engine damage.
11-4
SPECIFICATIONS
53MH0-74E
*1: When tire replacement is necessary and if the specified load index and speed rated tire is not available, then use a tire of higher load
index and speed rating.ITEM: Wheels and Tires
ALTO 800 ALTO K10
Tire size, front and rear145/80R12 74S*1 155/65 R13 73S*1
145/80R12 74H*1 155/65 R13 73T*1
145/80R12 74T*1 —
Rim size145/80R12 74S*1: 12 × 3.50B 155/65 R13 73S*1 : 13X4 1/2J
145/80R12 74H*1: 12 × 3.50B 155/65 R13 73T*1 : 13X4 1/2J
145/80R12 74T*1: 12 × 3.50B —
Tire pressuresFor the specified tire pressure, see the Tire Information Label located the driver’s door
lock pillar.
ITEM: Capacities (approx.)
ALTO 800 ALTO K10
Coolant (including reservoir tank) 3.5 L
4.5 L
Fuel tank 35 L35 L
Engine oil 3.0 L (replacement with oil filter)2.8 L (replacement with oil filter)
Transaxle oil 1.5 L
1.45 L
